Search Documents

By Anil Mahyera

This report present the results of a laboratory and field research program aimed at design and development of a torque-thrust controlled bolter with the capability to (1) predict the "quality of anchorage" attained while installing mechanical anchor roofbolts, and (2) improve the uniformity and tension levels achieved among a group of roofbolts. The prediction accuracy of the anchorage quality algorithm ranged from low to moderate because of the complexity and variability of the phenomena involved. The best roof support with mechanical anchor bolts was found to be achieved by simply installing them under ? proper torque-thrust control, and with ? a hardened washer under the bolthead. This procedure resulted in an improvement in uniformity of 3 times, along with an increase in mean tension levels of 75% over conventionally installed roofbolts.

Jan 1, 1983

By C. G. Maier

The present trend of chemicometallurgical research toward widespread and inclusive use of thermodynamic methods requires the inclusion of available data of this sort in any comprehensive metallurgical report . Such data for manganese are far from adequate for the full utilization of these methods . Even if our knowledge of these properties is weak , the collection of available figures is nevertheless well worth while , especially if their utilization in an approximate way may show inherent possibilities of application . No less important is the necessity for discovering the vital gaps in the existing information , to serve as a basis for further pertinent study . The utility of the thermodynamic methods of Lewis and Randall ( 234 ) 3 has become increasingly evident to metallurgists . It is true that at present no better approach to the general , fundamental problems of chemical metallurgy is available than close adherence to these methods . The effort is here made to collect and correlate , as far as possible , significant quantitative thermodynamic data on manganese and its metallurgically important compounds . There are considered here only the intrinsic properties of pure materials . The order maintained as far as possible will be as follows :

May 1, 1934

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By G. Titichoca

Modification of the blasting process considers that any increase in the energy consumption generates greater benefits if done in the later stages (associated with a larger decrease in energy consumption). Therefore, although the blasting cost is doubled, generating a greater proportion of fines in addition to a weaker ore (because with greater loads and appropriate distribution of explosives a greater number of internal cracks is generated), the reduction of the unit cost that occurs in the grinding stages (SAG and ball mills) generates a positive balance in the overall size reduction process. Codelco Chile, Division Andina, has developed an extensive experimental plan to evaluate the concept of blasting modification applying greater energy. This was implemented in two stages, each including a specific mine sector: La Union and Don Luis. This paper reviews the experience of implementing such blasting modifications at the La Union mine and its impact on the design concepts and the operation of the SAG mill plant

Jan 1, 2007

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By G. S. Scott, G. W. Jones

"INTRODUCTION An important phase of the accident-preventing program of the Bureau Mines is the determination of the explosion hazards of various combustible gases, vapors, and liquids encountered in mining and allied industries and the development of methods of eliminating or mitigating them.Recently, isobutane has become a commercially important raw material in the production of aviation gasoline by the alkylation process. 4/ in which isoparaffins are combined with olefins to give higher molecular weight compounds of branched-chain structure.Because of the anticipated commercial importance of isobutane in industry, it has been deemed necessary to study and determine its general explosion haz¬ards. This report gives its limits of inflammability, minimum ignition temper¬atures, and the amounts of nitrogen and carbon dioxide required to render isobutane-air mixtures noninflammable."

Jun 1, 1947

By Julio G. Poterico

La minería es una actividad económica de desarrollo sostenible que requiere de una adecuada gestión para garantizar el funcionamiento de los proyectos. En ese sentido, el presente trabajo describe el uso de la evaluación multicriterial optimizada (Modelo IMCA) para cuantificar las alternativas: externalidad positiva y negativa. El modelo IMCA es una metodología inclusiva, participativa, vinculante, medible, confiable y comprensible que jerarquiza alternativas y escoger el mejor escenario evaluado en un contexto holístico, de forma que este modelo aporta a la mejora de decisiones adecuadas y sostenibles y evita conflictos sociales.

Jul 1, 2012

By Emilio Caballero

El presente texto señala la eficiencia del sistema mecanizado aplicado a las minas subterráneas en Canadá donde se obtuvo rendimientos y costos de producción que permitieron hacer un mejor uso de sus reservas. En ese sentido, se analiza la mecanización y se compara su eficiencia con la Compañía Minera Alianza. Para ello, se revisa el diseño de la mina, selección de equipo, plan de entrenamiento, mantenimiento del equipo y servicio, stock de repuestos, trabajadores en determinada área, supervisión a los equipos y el aspecto laboral.

Jan 1, 1982

By Artur Camposo Pereira

O presente trabalho buscou explorar a aplicação da ultramicrodureza instrumentada na caracterização microestrutural e mecânica de materiais metálicos aço inoxidável 304L e liga NiTi Rica em Ni, ambos no campo austenítico. Para isso foi utilizado um ultramicrodurômetro instrumentado (Shimadzu, modelo DUH–211S) com medidas a temperatura ambiente e distintas cargas máximas e tempos de permanência. De acordo com algumas das possibilidades apresentadas, pode-se concluir que a ultramicrodureza instrumentada é uma ferramenta poderosa para a caracterização mecânica correlacionada aos aspectos microestruturais de materiais metálicos.

Aug 17, 2017

By Tatiana ?. Sedysheva, Vladimir V. Ivanov, Michail E. Melnikov, Irina A. Pulyaeva

"INTRODUCTIONHydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean [3, 4 - 8]. Now, commercial interests gain more and more attention. Mining systems are being developed which involve fragmentation of the crusts and their separation from the substrate. The effectiveness of such activities greatly depends on physico-mechanical characteristics of the crusts and rocks on which they form. This determines the importance of the engineering geological study of the objects.This article comprises the results of the engineering geological studies of the crusts samples (72 samples) and their underlying rock substrates (75 samples), which were carried out during the research cruises 6-06, 6-07, 6-08, 6-13 (2006-2013) on the Magellan Seamounts guyots in the Western part of the Pacific Ocean by the specialists of the State Scientific Centre Yuzhmorgeologia [10 - 13, 19, 20]. The authors of the article directly participated in the studies mentioned above.MethodsEngineering geological studies were carried out on board of the research vessel Gelendzhik and in the laboratories of NPA «Sevmorgeologiya». The studies involved the determination of the following parameters:"

Jan 1, 2017

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By Rafael de Araujo Silva

As ligas ß-Ti têm sido consideradas materiais com potencial para armazenagem de hidrogênio no estado sólido. A adição de elementos de liga estabilizadores da fase ß, tal como o Nb, retém esta fase metaestável em temperatura ambiente. Neste trabalho a liga Ti-40Nb (at.%) foi produzida via fusão a arco e suas características microestruturais foram caracterizadas visando avaliar os efeitos da aplicação da deformação plástica severa (SPD, severe plastic deformation) e da hidrogenação. A laminação a frio sob atmosfera de Argônio foi a técnica de SPD escolhida. Os resultados principais mostraram que é possível hidrogenar a liga fundida Ti-40Nb em temperatura ambiente após laminação a frio. Os efeitos da deformação plástica severa na microestrutura da liga, como a introdução de discordâncias, foram importantes para o aperfeiçoamento da cinética de absorção em temperatura ambiente (25 °C). Após a dessorção da fase hidreto (CFC) a microestrutura volta a ser constituída pelas fases ? (CCC) e ?” (ortorrômbica).

Aug 17, 2017

By A. Roy MacLean

"In the Maritimes, there are twelve coal areas. From east to west, these include the Sydney coal field, the St. Rose - Chimney Corner, Inverness, Mabou, Port Hood, Pictou, Colchester - Debert, Springhill, Joggins - Chignecto, Beersville, Lake Stream, and Minto. The first eight are in Nova Scotia while the remaining four are in New Brunswick.In all these areas, the coal was formed during the Carboniferous period, which existed some 300 million years ago. However, within this period not all coal formation took place during the same time. There were three main intervals, which occurred at the time that the Riversdale, Cumberland and Pictou groups were laid down (Hacquebard, 1970). The oldest coals are those of the Riversdale Group. These coals were of rather limited extent, and only a few mineable seams are present, particularly at St. Rose -Chimney Corner and Port Hood. From these two areas only 2 M tons have been extracted, and 'measured' resources of 7 and 9 M tons respectively remain. The Cumberland Group coals are confined to Cumberland County and include the coals of Springhill and Joggins River Herbert -Chignecto. Some 43 M tons have been removed and only 7 M tons of 'measured' coal remain, with an addit10nal 39 M tons of 'inferred' resources. However, there are additional resources at Springhill, which will be discussed in more detail in a later section. The coals of the Pictou Group are the youngest and the most abundant, both in actual number of seams and in regional distnbution. These coals were formed during the Westphalian C and D, a time during which the main coal deposition in Europe also took place. Here belong the coals of the Sydney, Inverness, Mabou, Pictou, Debert, Beersville, Lake Stream and Minto fields. Their total production amounted to 469 M tons or 91 % of the Maritime total of 514 M tons. The remaining resources of all Pictou Group coals have been calculated at 254 M tons of 'measured' coal and 949 M tons of 'inferred' coal. As can readily be seen, the bulk of both past production and remaining resources occur in the Sydney coal field. The Sydney figures represent 73% of total production, and 87% of total 'demonstrated' resources in the Maritime Provinces. Next to Sydney, the Pictou coal field has been the greatest producer, with 59 M tons; it also has the second largest 'measured' resources, amounting to 25 M tons. However in terms of 'inferred' coal resources, the Mabou coal field, ~ith 140 M tons, ranks second to Sydney."

Jan 1, 1985

By R. O. Pynnonen

This circular is a study by the Bureau of Mines of 346 accidents in underground iron-ore mines of the Lake Superior district from June 1949 to August 1954. These accidents caused 354 lost-time injuries, including 28 fatalities and 2 permanent-total disabilities. The accident reports were analyzed by the Bureau to show the causes of injuries and the time charges and unsafe practices or conditions that caused the accidents. Also shown are the times of occurrence, ages of the injured by job classification, and experience of the injured in mines and on the job being performed when hurt. Detailed information is presented on approximately 14 percent of the total number of Lake Superior district underground mine accidents that resulted in lost-time injuries during the period covered. These facts are presented to aid accident-prevention measures in underground mines and as a record for measuring future safety accomplishments.

Jan 1, 1956

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By Mônica Aline Magalhães Gurgel

A crescente preocupação da indústria automobilística com questões ambientais e com a segurança do condutor e passageiros, fez com que o setor siderúrgico desenvolvesse aços com maior valor tecnológico, entre eles surgiu os aços avançados de alta resistência, onde encontra-se o “Dual Phase” (DP) utilizado nesse estudo, que é caracterizado por uma microestrutura associada a uma matriz ferrítica com ilhas dispersas de martensita. Neste trabalho utilizou-se amostras de um aço baixo C e Mn, com micro adição de Nb e Mo, em desenvolvimento, onde se propôs uma avaliação das propriedades mecânicas através de um Ultramicrodurômetro, as amostras extraídas após a laminação a frio seguiram para o recozimento intercrítico, em escala laboratorial, com auxílio de forno Mufla e um equipamento de análise termomecânica (TMA), com 7 temperaturas de encharque distintas e subsequente resfriamento com patamar isotérmico a 600°C por 20 minutos. Onde observou-se que a utilização do ultramicrodurômetro instrumentado mostrou ser uma ferramenta com grande potencial para a avaliação almejada.

Aug 17, 2017

By Ycaro Jorge Maia da Costa

O desenvolvimento de estruturas com dimensionamento confiável requer o monitoramento de seus materiais, entretanto alguns processos de fabricação muitas vezes induzem modificações em seu comportamento mecânico. Isso faz com que as estruturas sejam menos confiáveis podendo causar redução da vida útil. Um dos processos onde isso acontece é a soldagem. Seu aporte térmico, modifica a microestrutura do material de tal forma a gerar três regiões mecanicamente distintas na junta soldada: Metal de Solda (MS), Zona Afetada pelo Calor (ZAC) e Metal de Base (MB), fazendo com que haja concentração de tensão na região afetada. Este trabalho se deteve em analisar o comportamento mecânico de uma junta soldada de aço inoxidável AISI 304 em comparação com o mesmo material não-soldado através da identificação dos gradientes de deformação, utilizando da Correlação Digital de Imagens (CDI) aplicada ao ensaio de tração. Os resultados provaram a capacidade da técnica de CDI em identificar campos de deformação mesmo em materiais anisotrópicos, como uma junta soldada.

Aug 17, 2017

By Paula Rodrigues Caumo

A aterosclerose é um termo geral relativo a diversas doenças relacionadas ao espessamento e perda de elasticidade da parede arterial. Atualmente os maus hábitos alimentares, combinados ao sedentarismo, podem levar a ocorrência de elevados níveis de colesterol na corrente sanguínea. Este fato aumenta o risco de obstrução dos vasos sanguíneos, limitando o fluxo do sangue para o coração. Desta maneira, para desobstruir o vaso sanguíneo e manter o lúmen arterial aberto é colocado um stent. Os stents são redes, normalmente de ligas metálicas, que servem para desobstruir os vasos sanguíneos. O tratamento de doenças das artérias coronárias e periféricas usando stents metálicos tem sido adotado nas intervenções médicas nos dias de hoje. No entanto, surgiram argumentos que indicavam os benefícios de remover o stent após este ter feito a desobstrução, originando desenvolvimento de stents biodegradáveis. Estes exigem propriedades mecânicas adequadas, biocompatibilidade adequada, garantindo uma baixa toxicidade dos produtos de degradação. Com isso, o objetivo deste trabalho é o estudo preliminar sobre stents metálicos biodegradáveis, como ferro puro, magnésio. Além disso, avaliar se os mesmos são adequados para aplicação à stents biodegradáveis, avaliando as propriedades mecânicas dos metais, biocompatibilidade e toxicidade dos compostos degradados ao longo do tempo de implantação.

Aug 17, 2017

By Claudemir Ribeiro

A lança de injeção de carvão pulverizado (PCI) é um método consolidado na indústria siderúrgica, que possibilita a redução do consumo de carvão vegetal ou de coque de carvão metalúrgico enfornado, além do ganho de produtividade. A seleção de materiais adequados para a lança de injeção é de suma importância para agregar ainda mais valor ao método. A finalidade deste trabalho é nortear a seleção das ligas aplicadas em alta temperatura, visando o melhor custo benefício, por meio das análises da resistência à corrosão, fluência e estabilidade estrutural. Foram realizados testes em uma usina siderúrgica chinesa com as ligas Sandvik 253 MA™ (UNS S30815) e UNS S32109. A experiência demonstrou como as siderúrgicas podem obter ganhos com a seleção adequada da liga. O custo-benefício do 253MA que é ligado ao Cério, Silício e Nitrogênio, mostra-se como uma ótima alternativa para o processo de injeção de carvão, devido a sua alta resistência à oxidação, à fluência e à erosão. Outras ligas como UNS S30403, UNS S31009 e UNS N08810, que são muito utilizadas em alta temperatura nas indústrias em geral, também foram analisadas como comparativo.

Aug 17, 2017

By Bruno Vidal de Almeida

A campanha dos refratários à base de carbono aplicados como revestimento de trabalho de diversos equipamentos siderúrgicos depende da soma de diversos fatores como resistência à corrosão, resistência à oxidação do carbono, estabilidade termomecânica, entre outros. Durante a etapa de aquecimento inicial de revestimentos refratários novos ocorre a oxidação prematura do carbono presente no revestimento refratário, reduzindo a vida útil do revestimento precocemente. Para reduzir a oxidação precoce do carbono foi desenvolvido um novo coating cerâmico que atua como uma eficiente barreira física, reduzindo o contato do oxigênio da atmosfera de aquecimento com o carbono presente no refratário. O coating desenvolvido possui uma fase ligante com pega química ativada termicamente e possui como carga refratária um composto sílico-aluminoso com elevada estabilidade térmica. Os resultados laboratoriais de avaliação de desempenho revelaram que com a aplicação do novo coating desenvolvido reduz-se a oxidação prematura do carbono em até 77% e elevase a vida útil do revestimento em alguns casos em até 15%. O coating desenvolvido revelou possuir excelente desempenho quanto a proteção do refratário MgO-C contra a oxidação do carbono que ocorre durante a etapa de aquecimento de equipamentos com refratários novos, comprovando sua aplicabilidade em diversos equipamentos siderúrgicos que possuem revestimentos refratários à base de carbono.

Aug 17, 2017