Search Documents

By E. H. Burroughs

HISTORICAL REFERENCES OCCURRENCE-GEOLOGY AND ORIGIN. 4. ARNOLD, RALPH. Conservation of the oil and gas resources of the Americas, Econ. Geol., vol. 11, Apr.-May, 1916, pp. 203-222; June, 1916, pp. 299-326; Proc. 2nd Pan American Sci. Cong., 1915-1916, vol. 3, Conservation of natural resources, pp. 207-237. Shows occurrence of oll, and status and possibilities of oil Industry in each country. Discusses briefly ways in which oll reserves may be conserved. 5. RUTIS, A. A. Petroleum known since remote times. Oil and Gas Jour., vol. 15, Nov. 2, 1916, pp. 33, 37. Gives historical reférences to the use of petroleum from Bible times to its discovery In America. See also Nos. 3, 257, 202, 337, 1843.

Jan 1, 1919

By W. L. Falke

This Bureau of Mines report illustrates critical path planning and scheduling techniques as applied to typical mining operations. Detailed examples of arrow diagramming and computer oriented applications of critical path methods are given. Program Evaluation and Review Technique (PERT) is discussed briefly in comparison to the Critical Path Method (CPM).

Jan 1, 1966

By M. R. Geer

This report presents the results of washability examinations of seven coals from the principal coal-producing fields of Montana. A complete performance test of the Baum-type jig operated at one of the mines is included, as are the results of cleaning tests made on two of the coals in a dense-medium pilot plant. The coals examined from the Red Lodge, Bull Mountain, and Forsyth fields are comparatively easy to clean. Ash contents of 5 to 10 percent can be obtained at yields of washed coal ranging from 90 to 95 percent. The coal from the Great Falls field, however, could not be cleaned readily to less than 14 percent ash, and the rejection of impurity would amount to over 25 percent. The two coals treated in the dense-medium pilot plant were characterized by sharp separation of impurity, high recovery efficiency, and satisfactory reduction in ash content.

Jan 1, 1955

By James A. Wasson, Harry R. Johnson, Dean W. Boley

The Cow Run sand was cored and electrical and radioactivity surveys were made in C. E. Vandevender well 35 in the Burning Springs pool of the Burning Springs oilfield , Wirt County , W. Va . Laboratory tests , reservoir - fluid analysis , well - log interpretation , and available field data indicate that a substantial quantity of oil may be recovered from this pressure - depleted reservoir by waterflooding . Two formations erroneously believed to be the First and Second Cow Run sands were similarly evaluated in A. E. Mackintosh well 8 , Anns Run Pool , Wirt County , W. Va . , but were found unsuitable for secondary - recovery operations .

Jan 1, 1964

By T. J. Rohrbacher

This report presents a U.S. Bureau of Mines methodology developed to incorporate factors of coal production (mining and cleaning methods, recoveries, economics, etc.) into the definition of recover-ability of a coal resource. Project procedures and computer models that were developed to include mine and preparation plant production rates, recoveries, and costs are explained. The results of these procedures and models are reviewed and compared to the Energy Information Administration estimate of U.S. coal resources-the "demonstrated reserve base." The Matewan 7-1/2-minute quadrangle in eastern Kentucky was selected to demonstrate the methodology.

Jan 1, 1993

By Jan C. Still

The Glacier Bay subarea is that part of the Juneau Mining District (JMD) within Glacier Bay National Park and Preserve (GBNP). It is the western portion of the JMD and consists of the land between the Fairweather Range crest and the Takhinsha and Chilkat Ranges crests (excluding that land east of Excursion Inlet.) Figure B-1 shows the area. It is bounded on the north by the Alaska-British Columbia International boundary, to the south by Cross Sound and Icy Strait, and contains Glacier Bay. During 1975 -1977 the Bureau conducted a detailed study of the occurrences, prospects, and deposits in GBNP (B_4).2 This work was in cooperation with the U.S. Geological Survey (USGS) under the provisions of the Wilderness Act (Public Law 88-577). As a follow up to this earlier Bureau work, limited studies were conducted, during 1985 and 1986, as part of the JMD study. This report covers the most important aspects of the earlier studies and the 1985 and 1986 studies. ACCESS The Glacier Bay area may be reached through Gustavus airport, a paved strip which is serviced by scheduled jet airliners in the summer and air taxi services year-round. The airport is connected to Bartlett Cove (GBNP headquarters) by an all-weather road. No other roads exist in the area except a skid road to the LeRoy Mine and mill in the Reid Inlet area. Much of the Glacier Bay area is accessible through the salt water inlets and fjords which are part of Glacier Bay. Cruise ships, charter boats, and fishing boats visit these inlets and fjords during the summer months. Elevations within the area range from sea level to over 15,000 feet in the rugged Fairweather Mountain Range. More remote areas are accessible by small boat, foot, or helicopter. Glacier ice is a year-round hazard to navigation in Glacier Bay, and during the winter months some of the more northerly inlets are frozen.

Jan 1, 2012

By R. R. Brandenthaler

The development of the Seminole area into one of the major oil-producing sections of the country has been accompanied by many innovations and departures from former methods of development. On July 1, 1929, two years and nine months from the date of discovery, 20,490 acres were considered proved, and additional acreage is constantly being developed. Because of its peculiar conditions, extent, and rapid rate of development, the Seminole area provided numerous problems, the solution of which necessitated research in connection with practical field operation; as a result, there was a radical departure from methods usually employed in the development of a new field in the Mid-Continent area.

Jan 1, 1930

By E. G. King

Many of the existing thermodynamic values for the titanium halides are estimates, including all the entropies and high-temperature heat contents of their crystalline and liquid phases. This report contains the results of low-temperature heat capacity measurents (which lead to entropy values at 298.15° K,) and high-temperature heat-content measurements of four halides - trichloride, tribromide, tetrabromide, and tetraiodide. The new data are combined with selected heat-of-formation values at 298.15° K. to obtain improved values of the heats and free energies of formation of these halides at high temperatures, thus supplementing the previous data of Kelley and Mah.5/ ACKNOWLEDGEMENTS This investigation was conducted under a cooperative arrangement between the Federal Bureau of Mines and the Department of the Navy, Office of Naval Research. The work was done by Bureau of Mines personnel using Bureau of Mines calorimetric equipment. The Office-of Naval Research supplied the supporting funds and arranged for procuring the samples of the titanium halides. The samples were prepared and analyzed by the Inorganic Chemistry Section, Division of Chemistry, National Bureau of Standards.

Jan 1, 1961

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

Operation of a pilot-scale Floatex density separator was studied using a pyrite concentrate slurry feed. Experimental measurements were further utilized in parameterization of a hindered settling simulation model. The model incorporates particle slip velocity calculation and also a separation efficiency function, adjusted to describe the feed material characteristics. The model was used to compute the overflow and underflow compositions when both fluidization bed pressure and teeter water flow rates were varied. In addition, prediction accuracy and the model validity were evaluated. The simulations gave good results when the teeter interstitial velocities were moderate enough to avoid excessive turbulence in the fluidization. Prediction of the cumulative overflow and underflow size distributions in most experiments yielded essentially less than 10% relative error between the sample data and the estimated value of the 50% passing sizes.

Jan 1, 2011

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

Kaiser Aluminum & Chemical Corp. announced that it planned to spend $66 million to increase the efficiency of its Baton Rouge, Louisiana, alumina plant. The improvements are designed to reduce energy consumption but will not change the annual capacity of the plant, now rated at about one million short tons. The project was expected to be initiated immediately and be completed by 1982. ALUMINUM Producers in this country posted unalloyed 99.5 percent aluminum ingot at 53-57.5 cents per pound, yet actual selling prices were closer to 53 cents. Domestic merchants quoted unalloyed ingot on a spot basis at 54-56.3 cents. London Metal Exchange 3-month forward contracts fell during November's trading from 55,2 cents to 52.8 cents per pound.

Jan 1, 1978

Duties on Lead Imports from Mexico. - On September 15, the President signed Proclamation 4792 suspending concessions formerly granted as of January 1 on red lead imported from Mexico. The Proclamation also increased the duty payable on litharge imported from Mexico from 3% ad valorem to 3.5% ad valorem, effective September 15. Appeal of Lead Standards. - The U.S. Court of Appeals for Washington, D.C., rejected petitions by the Lead Industries Assoc. and St. Joe Minerals Corp. for a review of standards promulgated by EPA and OSHA. The Lead Industries Assoc. reportedly will appeal to the U.S. Supreme Court on the basis of the "benzene" and "cotton dust" decisions. Scheduled implementation of standards will continue during the appeal.

Jan 1, 1980

By S. H. Lorain

Shortly after the Strategic Minerals Act of 1939 we passed by Congress, the Bureau of Mines was authorized to begin a program of investigation of domestic sources of strategic minerals. Since World War I, the Philipsburg district had been virtually the only one in the United States that was producing manganese on a commercial scale. Consequently, the district was among the first to he investigated. During the summer of 1939, the Geological Survey mapped the geology and ore deposits of the district. In late July 1939 the writer examined the district for the Bureau of Mines. On the basis of this examination and of the work performed by the Geological Survey, the Bureau of Mines diamond-drilled at several properties in the district during the summer of 1940. This report reviews the mining history and geology of the district, and presents the factual data obtained by diamond drilling.

Jan 1, 1950

By L. Roux

The initial evaluation of a coal deposit often raises uncertainty with regard to the accuracy of the reported Resources and Reserves. Reconciliation of results from mining and beneficiation with the original raw field data highlights deficiencies in original estimations. Credible Resource and Reserve estimation forms the basis on which an entire mining enterprise is motivated, initiated, funded, and established as a commercially viable proposition. This is required for sustainable extraction purposes and to support vital downstream industries such as power generation. Accurate determination of the density of the matrix of the material being evaluated is the key to credible values being obtained for Resources and Reserves. Losses between 15% and 20% of the Resource/Reserve can be realized if incorrect densities are applied to the tonnage derivation. Coal plies and particles have different relative densities, determined by the maceral composition, rank, and mineral and moisture content. These factors in turn contribute to the moisture, volatile matter, ash and carbon contents of a coal, which affect the overall density of the raw coal. More specifically, the relationship of ash to density and the effective matrix porosity were found to be critical in solving the greater majority of the problems in predictive calculations. A major deficiency identified is the inability to determine effective porosity, allowing absorption of adventitious moisture and altering the mass of the core sample. Although the volume of the raw material is altered through crushing, the change in mass after controlled air-drying, used with the original geometrical volume of the raw material, provides a credible air-dry density and allows the determination of the volumetric change related to effective porosity. This parameter can be validated through the evaluation of proximate ash using the ash-adjusted algorithm and a correction for the inherent moisture applied to also give a credible relative density value for an air-dried sample. A combination of theoretical, empirical, and reconciliatory evaluations of the available data, taken from the exploration phase through the mining process to final production, has shown that an integrated approach using the ash-adjusted density (AAD) methodology, in conjunction with other evaluative techniques, provides credible results with a considerably higher degree of accuracy than is currently possible.

May 1, 2021

The Rio Tinto Iron Ore group currently estimates grade attributes for mineral resources using ordinary kriging (OK). OK produces a smoothed globally unbiased estimate, but does not capture local variability, which can have significant impact on mine planning and scheduling. The dimensions and the multivariate nature of iron ore deposits make point simulations of whole deposits impractical. With a direct block simulation method the size and speed limitations of point simulations can potentially be overcome, resulting in a viable method for capturing local variability and for providing risk measures into the mine plan and schedules. Some iron ore deposits are highly folded (post mineralisation) and require preprocessing using an unfolding algorithm to properly define the continuity parameters and directions of anisotropy before simulation can proceed. Block co-simulation proceeds in unfolded space and since mine planning require a block-model with regular block-sizes; a regular block-model is unfolded first. This paper discusses a block co-simulation approach that can be used to simulate the irregular blocks resulting from the unfolding process. A section of an iron ore deposit is used for testing the block co-simulation algorithm and the simulation results are compared against the Isatis direct block simulation method. Available blasthole data is also used to validate the behaviour of the block co-simulation algorithm.

Sep 26, 2011

By R. S. Fowkes

The Bureau of Mines constructed a fully automated pilot plant facility to study the hydraulic transportation of solids through a lock hopper feeder system. An equation for the energy requirements to transport coarse solids hydraulically proved applicable to this system. Optimum velocities were obtained for limestone, mine refuse, and bituminous coal. The experimental data, calculations, and graphs show the effect of velocity, specific gravity, and solids concentration on head loss and power requirements. Other data were obtained and evaluated to determine the effect of particle size on head loss. Results also are given for (a) tests using friction reducing polymers; (b) tests using seven test sections of steel alloy pipe to determine their wear characteristics; (c) tests to determine spatial segregation of moving particles; and (d) tests to determine the effect of shape, size, and specific gravity on particle velocity in a horizontal pipeline. The lock hopper feeder system was found practical for continuous hydraulic transportation of the material types and size ranges tested.

Jan 1, 1969

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966