Search Documents

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011

"El presente texto señala las formas en que se presenta el sílice libre y las principales rocas constituyentes del material generador de la silicosis. En ese sentido, el ""sílice libre"" se presenta a través de tres formas: cristalizada, criptocristalina y amoría. Sus diversas variedades en forma de cuarzo son el cristal de roca, el cuarzo amatista, cuarzo rosado, amarillo, ahumado, lechoso, ferruginoso, etc. De otro lado, la presencia del cuarzo en las rocas ígneas sirve de base para su clasificación en ácidas, intermedias, básicas y ultrabásicas. Las rocas ácidas son las que contienen más de 10% de cuarzo, las intermedias menos de 10% de cuarzo y las básicas y ultrabásicas, carecen de este mineral en su esencia. Asimismo para determinar el grado de peligrosidad del polvo es necesario revisar la concentración de partículas de polvo, a través de una muestra y cuenta de los mismos. El muestreo se basa siguiendo diferentes técnicas basadas en principios fiísicos como filtración, estrellamiento, precipitación electrostática y térmica. Mientras que la cuenta de partículas se efectúa mediante un microscopio provisto de un sistema óptico standarizado y diferentes tipos de celdas (Dunn, hemacitómetro y la celda Hatch). Cabe aclarar que no es posible la comparación de peligrosidad de dos polvos, basándonos solo en el componenente sílice, sino que el tamaño de las partículas y la concentración en el ambiente, son factores a considerar para su evaluación. Entre los métodos importantes de determinación cuantitativa de sílice libre tenemos: químicos y físicos. Los primeros, utilizan la descomposición de todos los componentes de la muestra -con excepción del sílice libre-a través de un tratamiento ácido, mientras que los segundos son más precisos respecto de los polvos industriales y se realizan a través de análisis petrográfico, difracción de rayos y el método de fusión. Posteriormente, la Asociación Americana de Higienistas industriales revisa los datos encontrados en África del Sur, Australia, Inglaterra y Estados Unidos, y hace un esbozo sobre los límites de tolerancia permisibles de polvo, revelando que el polvo contenido con más de- 50% de SiO2 es equivalente a 5 MPPPC, los que tienen de 5 a 50% de SiO2 tienen 20 MPPPC, y aquellos que contienen hasta 5% deSiO2 equivale a 50 MPPPC, a diferencia de otros métodos propuestos."

Jul 20, 1957

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

An upgrade to Vale?s existing Clarabelle dual-pinion, semiautogenous (SAG) mill was completed by the power and automation technology company, ABB. The mill is used to reduce the size of the ore at the company?s nickel and copper mines in the Sudbury area. The project was completed on time and on budget with an excellent safety record. Located in Ontario about 400 km (250 miles) north of Toronto, Vale?s Sudbury operations are primarily underground nickel sulfide mines, with integrated mining, milling, smelting and refining operations. One of the characteristics of Clarabelle Mill is to accept nickel-copper ore from various sources and companies and to produce a nickel-copper concentrate and copper concentrate for further processing. The size of the ore is further reduced in SAG mills, rod mills and ball mills, where all milling is done wet.

Mar 1, 2014

By J. Lui

The 15m high Inco flash furnace uptake was designed as a reaction chamber with the objective of destroying the H2S contained in the furnace off-gas by combustion with oxygen at about 1300?C. Until recently, the oxygen required for this purpose was injected through afterburners located at the bottom of the uptake. An undesirable side effect of this practice was the formation of build up accretions on the inside walls of the uptake. This buildup had a negative impact on both the furnace on line time and the control of the flash smelting process. In late 200 I, the afterburners were relocated to the roof of the uptake. As a result, about 80% of the uptake accretion buildup disappeared with obvious beneficial effects for the operation of the furnace. This paper discusses key flash smelting aspects that affect the operation of the flash furnace uptake such as the dusting rate, the formation of H2S in the freeboard of the furnace, and the impact of using coke to supply some of the heat required by the process. The mechanism of buildup formation and its dependence on uptake afterburners location are also examined. Prof. Yazawa's sulfide smelting thermodynamic relationships proved instrumental in understanding the conditions that influence the formation and the elimination ofH2S and uptake buildup.

Jan 1, 2003

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c',ov~-lo.pe;t by tL1e '.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.'l. :.-,,- #?,n c-noot'fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(' the c8n:xcity oi' the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn'rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o'q7r ir.:,l soon t ire:. the oyernt or]

Jan 1, 1938

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

By R. H. Sprute

This report describes a feasibility study to consolidate coal waste sludge in a 100-acre pond by applying direct current between floating and buried electrodes. The study was conducted by the Bureau of Mines under a cooperative agreement with Washington Irrigation and Development Co., located near Centralia, Wash. Part 1 covers results of laboratory tests at the Bureau's Spokane Research Center and a small-scale field test at the cooperator's coal preparation plant in western Washington. The process is efficient and cost-effective when power is applied at low current density. A proposed system, fully described in part 2, has electrodes covering 21 acres of pond surface radially arranged around a central power platform. Densification of pond contents would require 2 to 3 years of treatment. Total cost of equipment, labor, and material is approximately $500,000.

Jan 1, 1982

Amercable, Inc. Andalex Resources, Inc. ARCO Coal Company Behre Dolbear & Company, Inc. Colowyo Coal Co. L.P. Continental Conveyor & Equipment Company Crane & Hoist Sales Crested Butte Mountain Resort Cyprus Amax Coal Co. Energy West Mining Company The Falkirk Mining Company Fleischli Oil Co. Inc. Halbach & Braun Industries Hemscheidt Corporation GH Henley Industries Ingersoll-Rand Co. Jennmar Corporation Joy Technologies, Inc. K & P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation L & H Welding & Machine Co. McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Western Coal Company Phillips Machine Service Pincock Allen & Holt Ramsey Technology, Inc. Rust Tractor Company Salt River Project Schroeder Industries Stamler Corporation TerraMatrix TIC (The Industrial Company Wyoming, Inc.) Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1994

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are' much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in 'heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Oliver Bowles

"Score of the Bureau's Investigations.There has been outlined in a previous report* the results obtained regarding the adaptability of pulverized waste slate as a filler in road asphalt mixtures. As pointed out in that report the percentage of waste at slate quarries is very high, and the Bureau of Mines has undertaken the problem of discovering new and enlarged outlets for the waste material.Many products such as paper, rubber, road asphalt, floor coverings, paints, etc., require as one of their important constituents a considerable percentage of finely pulverized inert mineral matter to give ""body"", to obtain the desired consistency, or to supply the necessary wearing or other qualities demanded. Such materials are known as ""fillers"". The possibility that slate flour might be used as a filler with advantage in several products other than road asphalt led the Bureau to undertake further investigation.The Importance of Discovering Advantageous UsesIt has been found that in some products slate may be substituted for materials now in use without any marked effect on the quality of the products. A wider use of slate in such products could result only from a definite price advantage as compared with other fillers. Mile it is probable that waste slate may be placed on the market at prices which will encourage its wider use, it is evident that a waste slate utilization industry can never attain sufficient magnitude to definitely assist the slate producers unless it is demonstrated that some definite advantage in quality may be gained when slate is substituted for fillers now in use. The main purpose kept in view throughout the inquiry has been, therefore, to find advantageous uses for waste slate in order that both producer and consumer may be benefited."

Sep 1, 1921

By Herbert Drechsler

El texto analiza las relaciones entre el valor efectivo neto (net present value) de una inversión y los criterios de los retornos de capital (payback). Mientras la realización de una inversión prosigue en minería, puede ser que se descarte el seguimiento simultáneo de futuras alternativas de inversión. Esto es válido al menos para una época de medios de inversión limitados. Asimismo, es importante evaluar nuevos proyectos de inversiones, donde se ofrecen algunos instrumentos de Management con el fin de reducir las pérdidas (regrets) de una inversión demesiado prematura.

May 1, 1976

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By I. C. Brown

Introduction Many tables of nomenclature for igneous rocks have been introduced from time to time, and each has its strong proponents. As a result, any discussion of igneous? rocks is apt to prove confusing unless the names used for these rocks are defined. This ?became so obvious to a discussion group, formed by the members of the Geological Survey of Canada in 1948, that an attempt was made to establish a scheme of nomenclature that could be used by any member mapping anywhere in Canada. The writer was asked to co-ordinate the ideas presented by individuals in the discussion group, to arrange them in tabular form, and, later, to distribute copies of the resultant table to Canadian universities, provincial geological surveys, and some other geological discussion groups. Many useful suggestions and criticisms were received, were studied ?by members? of the original group, and, so far as practicable, were incorporated in the scheme of nomenclature. The result is the table presented here. This nomenclature of igneous rocks is at present being used by most members of the Geological Survey of Canada who are working with igneous rocks, and by some Canadian universities. We hope it will be found useful and be more widely accepted. With this idea in mind, certain principles were adopted in drawing up the nomenclature.

Jan 1, 1952

By M. Elmadagli

Wear mechanisms of two commercial aluminum alloys, namely a spray formed and extruded Al-25%Si alloy, and a sand cast A390 alloy (18.5 %Si) that are known to be successful in cylinder bore technology were studied to have a better understanding of the requirements for wear resistant aluminum alloy design. From durability point of view these alloys are known to be successful for engine bore applications. It is interesting to compare the wear mechanisms in these alloys because they have significantly different silicon content and microstructures, and were produced using different techniques. The wear tests were done using a block-on-ring configuration, in controlled air atmospheres (5 % relative humidity). In spite of the differences in silicon content and microstructure, the wear mechanisms were similar and consisted of formation and destruction of hard tribolayers that are either formed by either mechanical or chemical interactions on contact surfaces. The differences in the wear rates between the two alloys arose from the differences in the hardness of the worn surfaces, and the alloy's ability to sustain the tribolayers on the worn surfaces.

Jan 1, 2004

Power plants that utilize conventional wet flue-gas desulfurization methods produce enormous amounts of flue-gas scrubber sludge. A typical 400 MW power station that burns a high sulfur coal produces 170,000 tons of wet flue-gas scrubber sludge per year. This scrubber sludge is currently landfilled at an enormous cost to utility companies. This material could be used as a raw material for industries that use gypsum, such as the wallboard and plaster industries. However, before it can be used as feedstock for these industries, some of the impurities such as unreacted limestone and silicates must be removed from the scrubber sludge. Froth flotation has tremendous potential for separating these impurities from scrubber sludge. In order to select an optimum flotation process, it is necessary to characterize the surface properties of the major components in the scrubber sludge, which consist of calcium sulfite, calcium sulfate, calcium carbonate (limestone), and silica. In this study zeta potential measurements were used to determine the surface charge of the components in scrubber sludge, with the goal of optimizing a froth flotation process to produce a marketable gypsum product for the wallboard and plaster industries.

Jan 1, 1996

By H. E. Brauer

PART I INTRODUCTION Among the zinc base alloys used for casting in metal moulds, particularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortness which facilitate casting. Objection to the use of these alloys may bee raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intercrystalline corrosion. In all cases which have come to our knowledge where the conditions of service were known, failure has occurred upon exposure to moisture and heat varying from a hot moist atmosphere to high pressure steam. Moreover, the alloys described in all such cases contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intercrystalline oxidation in zinc-aluminum alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Bauer2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the most part, and Rawdon's3 examinations were made on an alloy containing 0.4 per cent. lead also exposed to the Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to determine the exact nature of this phenomenon and the effect of other metals present as impurities or intentional additions in accelerating or-retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation.

Jan 8, 1922

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017