Search Documents

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

By J. F. Lewis

Much has been written on this great engineering work, principally from the civil engineer's stand-point. In presenting the subject to the Institute, it seems necessary to include something of geology as well as engineering. In this case, it is particularly the glacial and post-glacial periods with which we are concerned; for it has been clearly proved that the canal recently excavated has not for the first time opened the Des Plaines valley for drainage away from Lake Michigan, and that this valley, as well as the site of this city, is very closely connected with the processes and effects of the ice period. We have simply renewed a channel and a drainage direction which formerly existed. As the days of deep water-ways for commercial purposes are fast approaching, engineers may find the consideration of ancient topography and geologic changes highly useful. For what I may say on this subject I am greatly indebted to Mr. Ossian Guthrie, who has made an earnest study of glacial geology and labored especially to decipher the records of its history in this region. * Chicago is situated in the track of one of four great glacial ice-streams that swept down from the North: one moving due South from Marquette and entering the Illinois valley at Ottawa; one through the Lake Michigan valley, entering the Illinois valley near Lemont; one from Saginaw Bay diagonally across the States of Michigan and Iadiana, entering through

Jan 1, 1898

By John C. Draper

The principal object of an underground coal mine transportation sys- tem is to move coal from the face where it is produced to the outside of the mine where it is prepared for market. In addition to the movement of coal, a transportation system must also move supply materials to the inside; it must move men in and out of the mine; and it must move rock and other debris out of the mine for disposal. Usually, mine haulage is divided into three categories named for the various areas of the mine served : 1) Pace Haulage. This is used at face from the mining machine to the intermediate transport system. 2) Intermediate or Secondary Haulage. Generally this is used between face haulage and main haulage. Sometimes this is merely an extension of the main haulage. 3) Main Haulage. This extends from the secondary haulage to the outside and is usually either a track or conveyor system, sometimes a combination of both. Transportation modes of coal in the various areas pose different problems, but the whole system must be synchronized. For instance, at the face the coal should be removed quickly from the various places to facilitate the movement of machines, whereas the intermediate system just passes the same coal on to the main transportation system. Selection of the transportation system must be based on the seam height, mining methods used to extract the coal, capacity required, ease of coal handling, and haulage efficiency. When driving rooms, mine cars can be used. They often simplify supply haulage and rock handling because they can also handle these items. Conveyors could be used and would have a greater haulage capacity but they cannot handle supplies easily or segregate the rock. When using a different mining method, such as longwall, mine cars cannot be used because there is not sufficient space to move the cars at the face nor can the cars haul the coal without delays which would cause excessive losses in production. As for ease of handling at a longwall face, conveyors are convenient because of their low height, ruggedness, and ability to operate while being advanced. Similarly, in low seam heights, conveyor systems are easier and more economic to operate than the regular track haulage because roof has to be taken down for handling mine cars of adequate size.

Jan 1, 1981

By Nathaniel Arbiter, Norman L. Weiss

Factors now accelerating the trend to larger concentrators and larger equipment units are reviewed. After almost 40 years of stability with unit sizes less than 100 cu ft, 200 and 300-cu-ft flotation-cell units are now operating and a 500-cu-ft machine is being built. The design of these cells is considered, as is the design and operation of flotation circuits against the background of the need to achieve greater process efficiency while holding down operating and investment costs. Particular attention is paid to the scale-up problem. With the newer cells having five to ten times higher unit capacities, the advantages resulting from this in sampling, mill operation nnd control, testing and plant layout are indicated, as well as the broad direction for changes in the overall design of 50,000 to 100,000-tpd concentrators. A comparison is given of the available larger cells of U.S. manufacture with analysis of differences and similarities. After almost 60 years of application in this country, froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups, the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign, the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency. and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum—to mention only the most important metals occurring in the U.S. as sulfides- must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000-tpd milling rate on copper ores. Table 1' shows the trend in copper ore grades in U.S. in recent years. Table 2' shows the projected annual growth rate of consumption 1966-1985. A study by one of the authors 25 years ago showed that of 32 copper mills in North America with more than 100-tpd capacity, only eight had capacities exceeding 10,000 tpd. The average for these eight was 25,000 tpd. These included the three giants of that day, Magna, Arthur, and Morenci; the other five averaged a little over 10,000 tpd. Today instead of the eight mills with capacities exceeding 10,000-tpd capacity we have 25, and the mill with less than 1000-tpd capacity is fast becoming extinct. Much less range is found in lead and zinc mills, which are still generally small except for the few with over 1000-tpd capacity in Missouri, Utah, and Idaho, and a few zinc ore mills in the same size category. Molybdenum and potash operations are the fastest growers in North America today, but when one considers the projected increase in consumption of copper together with the projected decrease in grade of ore (3% annually), he can foresee that copper ore milling will soon lead the list. Technological improvements to meet the challenge of lower-grade ores have taken the wholly predictable path toward bigger equipment. In mining, shovels, draglines, scrapers, and trucks have led the way; in ore processing, we have seen a rapid increase in size of grinding mills, flotation cells, and pumps. Twenty-five years ago, for example, the 10-ft-diam ball mills treating 2000 tpd at Morenci were considered the giants, but today some grinding mills in similar service have five times that capacity. The specific matters to be dealt with in this paper are 1) the underlying principles that affect flotation-machine design, and the conditions required to produce

Jan 1, 1971

By A B. Richards

Effective control of blast vibration and flyrock requires that significant factors be identified and quantified, that the blast be designed to ensure both blasting efficiency and compliance with applicable limits, and that the blast design be effectively implemented by field personnel. Significant factors contributing to ground vibration and airblast are: charge mass; distance and direction relative to the blast; drilling design: burden, spacing; stemming height and material type; hole diameter and depth; and initiation sequence and direction.In addition, airblast may be strongly influenced by shielding and meteorological conditions. Ground vibration is also influenced by the transmission characteristics of the ground and soil. Flyrock throw is determined by charge mass, burden, stemming height, blasthole diameter and depth. The contribution of each of the factors has been quantified and models developed to enable the environmental outcomes of blast design to be predicted. Environmental blast design is necessary to ensure compliance with regulatory limits and the implementation of æsafeÆ exclusion zones for flyrock clearance. This paper discusses the models used for environmental blast design and demonstrates the often significant effects that lapse during implementation of the design can have on predicted outcomes. In practice, drillers and shotfirers are sometimes confronted with situations that require modifications to the blast design to cope with the real site situation. Methods are presented that may be used by drillers and shotfirers to evaluate the effect of these modifications, the tolerances that must be reached during their work practice and checking procedures, and the consequences of their actions.

Jan 1, 2004

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,' or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By D. J. Weintritt, R. G. Hughes

Statistics show arz increase in the average depth of wells drilled in recent years. As a corollary to this trend, drilling fluids have been improved in an effort to meet the problems inherent at temperatures approaching 500°F. Of importance are (1) deterioration of mud components and (2) the effect of solids on filtration and rheological properties. High-temperature, stable water-base and oil-bare muds are discussed. Those areas in which differences exist are pointed out. Results are based on data taken from the Fann consistotneter, rheometer and shear-strength measurements, static and dynamic filtration tests, methy-lene blue test for bentonite solids and specific heat measLrrenlents of muds. INTRODUCTION Higher well temperatures go along with the fact that the average depth of wells continues to increase. Recent data by Gardner' lists 137 completions deeper than 15,000 ft for the first half of 1964 with a record second-half total of 167 wells drilling or proposed. In addition, there has been an increase in drilling for steam for power production or mineral recovery. In this application the depths are modest, but the mud may approach the critical pressure and temperature of water. Scearce and Magnon' report drilling mud used at temperatures of about 700°F in the Salton Sea area of California. Most deep wells have been drilled with water-base muds. In recent years, however, there has been a substantial increase in the use of oil-base muds because of technological advances in effective additives. The significance of this development was dealt with in considerable detail by Simpson and his co-workers.3 Additiona1 field data have now been obtained to indicate that oil muds are competitive in control, performance and cost with the best types of water muds for use at high temperaturc. This parallel offer of two very different fluid systems, each offering a similar variability in performance, cost and convenience, has created the need to evaluate the merits of these fluids under specified conditions so that the advantages and disadvantages of each can be weighed in relation to the over-all drilling program. This paper is not intended as a review of all the factors. Rather, it attempts to emphasize: (1) important condltions and facts peculiar to high-temperature drilling muds, (2) that more than one imposed test condition or testing method is necessary to describe the quality of a mud at high temperature and (3) that elaborate experimental precautions are necessary whenever laboratory data are used in selection of a mud for field use. WHAT IS A HIGH-TEMPERATURE DRILLING FLUID? For the purpose of this discussion, a high-temperature drilling fluid is any system so formulated or treated to economically minimize the effects of temperature on the properties of the fluid. Our experience in drilling fluids suggests that these effects become obvious for many mud materials at temperatures of 300F or higher. It is understood that hydrolysis of starches, depoly-merization of certain organic thinners, or irreversible chemical reactions (such as that of clay and lime) can affect filtration, viscosity and shear strength at less than 300F. However, the temperature level is not a serious point and in no way affects the precautions and techniques used in this study. An up-to-date review of the literature on high-temperature drilling fluids and the many variations was treated by Rogers'in 1963. EXPERIMENTAL REQUIREMENTS TESTING EQUIPMENT AND PROCEDURES With the advent of deeper drilling and increased demand for temperature-stable drilling fluids, new testing equipment and laboratory techniques were devised for the evaluation of drilling fluids subjected to elevated temperature and pressure. While the equipment has not been standardized, it is in widespread use. Milligan et al. Qescribe a filtration cell for determining the filtration properties of drilling fluids at temperatures in excess of 300F. They showed the effect of variations in temperature and pressure on oil and water muds filtered in the 300 to 400F range. The dynamic filtration apparatus described by Simpson6 permits the study of the filtration properties to temperatures of 350F for drilling fluids circulated over sandstone cores. Watkins et al.' describe the use of pressure bombs for studying the effect of prolonged periods of elevated temperature upon the gelation or solidification of drilling fluids. Chisholm et a1.' describe the use of a modified cement consistometer adapted for use in drilling fluid evaluations. A similar consistometer is used in this study, although the application and data-recording method have been changed. The consistency of a mud sample is measured by timing the movement of a soft iron bob which is magnetically moved up and down in the sample container.* Changer in the time of travel and the temperature of the mud at that moment are plotted with a two-point Brown Elec-tronik Recorder. A 10-in. chart with a speed of 4-in./hr is used. Fia.- 1 is a generalized internretation of the data ob-

Jan 1, 1966

By V. Silins, J. Tameling, R. C. Cook

"A general review of the wear problems encountered in the mining industry is presented and current practice for wear protection systems is reviewed.A new concept in wear protection is described and compared to alternative systems. Utilization of conventional stud welding technology and abrasion-resistant wear studs is shown to be a useful supplement or substitution for conventional techniques. Operating life of many consumable components can be increased by up to four fold. The technique is highly portable for on-site field application or can be used in shop environments.Details of the wear protection model and metallurgical properties of the wear component are also reviewed. Laboratory wear test data are reported to supplement field test performance or to screen potential alloy compositions for application in specific environments.A Review of Wear Problems and Wear ProtectionThe emphasis on wear protection has increased in recent years because of the increasing impact of the potential savings in time, materials and energy. A 1974 German study concluded that attention to tribology, the study of friction and wear, could save approximately $3 billion, and a study in the U.S.A. at the same time put the figure at $100 billion of which $20 billion was for materials. A more recent American study put the energy component of the potential savings at $16.2 billion per year. A recent British study estimated the total potential savings in the U.K. as $1 billion per year, with the largest savings coming from lower maintenance and replacement costs ($500 million), lower breakdown costs ($250 million) and increased machinery life ($200 million). These three major contributions are all potentially accessible in the mining industry."

Jan 1, 1982

By Richard I. Petritz

A brief review of today's processing of integvated circuits is given. The major trends in the development of advanced integvated electronics are identified as 1) the broadening of the integvated circuit concept to a large class of circuit function, 2) the processing of more complex circuits within relatively small chips of silicon, and 3) the processing of very large electronic functions on complete slices of silicon. This latter trend, called array technology, is then developed in detail. Emphasis is given to defining the key tech-nological problems. Current progress being made is illustrated. THIS paper will endeavor to identify the major trends in advanced integrated electronics technology. One of these, array technology, will be developed in some detail. The array technology discussion will identify the key problem areas. Since it is the scope of the entire meeting' to present specific progress in the science and technology of integrated electronics, we shall indicate general directions being explored rather than discuss comprehensively solutions to the problems. In order to set the stage for the discussion of future trends in integrated-electronics technology, let us briefly compare the processes by which circuits are fabricated through discrete-device technology with that of integrated circuits technology. The reader is referred to the December 1964 issue of Proceedings of IEEE2 for a comprehensive review of integrated electronics. The article3 by Jay Lathrop is an excellent discussion of integrated-circuits technology. A discussion of the history of semiconductor technology is contained in Ref. 4. A) Current Status of Integrated Electronics. Fig. 1 (top) shows the process by which circuits are constructed from discrete devices. Key points are: 1) Slices containing large numbers of transistors or diodes are processed separately. 2) The slices are scribed into small chips (on the order of 15 mils on a side is about as small as can be conveniently handled) each chip containing one transistor. 3) Each device is specified separately—circuit -function specs are derived largely from device specs. 4) Circuits are formed by connecting together the discrete devices. 5) The number of circuit connections required is approximately equal to the number of devices. 6) There are potentially many more discrete devices per inch2 of semiconductor—only our lack of ability to handle them in discrete form prevents us from going to several orders of magnitude higher density iin Fig. 1, 400,000 transistors are discussed at 1.5 mils on a side). The bottom part of Fig. 1 illustrates the integrated circuit process. Key points are: 1) On the same slice of silicon, transistors, diodes, and resistors are processed grouped to do a complete circuit function. 2) While still in slice form, the components are interconnected into circuit functions by an evaporation process, eliminating the need for separate interconnection steps later. Dramatic improvements in cost and reliability are realized. With a simple flash of metalization thousands of interconnections are reliably made. 3) The slices are scribed into chips which contain complete circuit functions. 4) The circuit functions are specified-not each component in the circuit. This important point was missed by some of the early opponents to integrated circuitry. They argued that, with device yields at x pct, integrated circuit yields would be pct, where n is the required number of devices to make a circuit. This argument leads to extremely low yields for integrated circuits. The fallacy of the argument is that in integrated circuits each device is not specified separately. Furthermore, since a device is forever integrated into a specific circuit function, it need meet only the requirements for that particular function. Discrete devices, on the other hand, are tightly specified so that they can be applied to a variety of circuit functions. 5) Extremely high packing densities are achievable because one need only make the basic devices as large as the circuit demands. Their size is not dictated by handling requirements. A current example

Jan 1, 1967

By W. A. Hutchins

Water laws important to the mining industry are those which govern or affect the right to use water, to dispose of water after using it in mining or milling, and to discharge waste material into watercourses. They include statutes and court decisions having general applicability, as well as others that pertain specifically to mining. THE INDUSTRY'S CONTRIBUTION TO WESTERN WATER LAW Despite sharp differences of opinion, the water law the Spaniards brought to the Southwest appears to have included some form of appropriation of water. The Mormons, who settled in Utah in the mid-nineteenth century, also developed a system of appro-priative water titles. But by far the most profound impact on western water law was made by the gold-seekers who flocked to the Sierra Nevada foothills of California after the discovery of gold in 1848. Much of the gold was extracted from the ground by hydraulic or placer mining, and so the miners' rights to the use of water became fundamentally important. Since there was no organized government in the foothills and no laws other than those made by the miners, they helped themselves to the land, the gold, and the water needed to work their claims.1 They established and enforced regulations governing the acquirement and holding of mining claims and their rights to the water they needed.' In 1879 Justice Field, former Chief Justice of the California Supreme Court, spoke for the U. S. Supreme Court in saying that the miners were "emphatically the law-makers, as respects mining, upon the public lands in the State."" Rules of the California mining camps were based on two essential principles: 1) priority in discovering claims and appropriating water by diverting it from streams and putting it to use, and 2) diligence in working claims and applying water in mining. The customs so developed, which were copied in mining areas of other states and territories, were enacted into law in one western jurisdiction after another. They form the basis of what is called the arid-region doctrine of prior appropriation of water, which received the attention of Congress in legislation recognizing and protecting appropriations of water for mining, agriculture, and other purposes on the public domain.' In several western states a great number of water cases decided in the early years involved relative rights to the use of water for mining purposes or for milling connected with mining." The miner's inch, the customary unit for measuring water in the mining camps, is still used in various western communities, although its relation to the cubic foot per second varies from one area to another. Undoubtedly, the miners of a century ago made the major contribution to the appropriation doctrine as it is now recognized and applied throughout the West. What inspired the California gold-seekers to develop these principles? Thoughtful writers have pointed out that their regulations and customs were strikingly characteristic of much earlier mining enterprises in the Old World.D It is said that the right of free mining and free use of flowing water therefor —so similar to the California conditions and practices—-was a part of the customs of Germanic miners in the Middle Ages, that it spread from middle Europe to other countries and colonies, and that the doctrine of prior appropriation was widespread in the important mining regions of the world. Certainly the Forty-niners came to California from many countries. It does not tax the imagination to consider that they may have brought with them some knowledge of the old Germanic customs and applied this knowledge in their new environment. RIGHTS TO USE OF WATER IN GENERAL In the West, rights to the use of water of watercourses fall into two categories—appropriative and riparian. The doctrine of prior appropriation is recognized in each of the 17 western states. The riparian doctrine is recognized concurrently with the appropriation doctrine in some of these states but has been abrogated in the others. The riparian doctrine prevails generally throughout the East, although there is now considerable interest in developing something else. Generally speaking, the appropriation doctrine has been highly developed in the West, whereas the principles of riparian doctrine have been comprehensively established in only a few states throughout the country. The subject of water rights is a big one. Space permits no more than a brief discussion of aspects that bear upon the title of this article. RIGHTS OF PRIOR APPROPRIATION Fundamental to the doctrine of prior appropriation is the principle first in time, first in right. Although in some states there are statutory exceptions. the original and still generally prevailing rule is that the first one who initiates a right to divert and use water of a stream, and who completes his undertaking with reasonable diligence, acquires thereby the first right of appropriation of the specific quantity of water involved. Each succeeding right in point of time is junior to all earlier rights but senior to all later ones. The practical effect of this priority system is that when the water supply is not enough for all, the earliest rights must be fully satisfied before any water may be taken by those later in time. Acquirement of Appropriative Rights: Each of the 17 western states has a statute under which water may be appropriated pursuant to a prescribed procedure. Generally, the first step to be taken by the intending appropriator is to file application in the office of the State Engineer for a permit to make the appropriation. In most but not a11 states, valid ap-

Jan 1, 1961

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989

The effectiveness of three different types of longwall chock under the three different types of geological conditions worked recently is outlined. Some provisional analyses of the variation of chock load under the shale roof con- dition are briefly discussed and some problems and solutions of gateway and road- head support outlined.

Jan 1, 1974

By Fernando J. A. S. Barriga

"Recent concerns over the availability of many mineral raw materials, and newly available technological developments, produced renewed interest in deep-sea mining. However, environmental concerns, with variable degrees of justification, are raising opposition to the concept. The forecast for the behavior of consumption versus availability of many raw materials, nearly all critical metals, arguably show that consumption will grow much faster than resource discovery onshore. Finding new sources of raw materials seems inescapable. The deep seafloor stands out as the only likely candidate.Sea Floor Mining and the EcosystemMarine mining has already started, decades ago, for diamonds, currently up to depths near 400m. Although the industry recognizes there is a footprint, it considers the footprint quite minor, because the area mined is small: in Namibia, where offshore diamond mining is now 70% of the country’s total, only 3% of the concession of 3,700 sq miles (9600km2) have been mined. As plans to mine deep-sea massive sulphide deposits and polymetallic nodules progress, the environmental concerns grow. Some of these concerns are as follows:?The deep-sea ecosystems are composed of long-lived species, with low rates of reproduction. The environment may not recover from mining on a human time scale;"

Jan 1, 2017

PRESIDENT BUBB: Gentlemen, this gathering marks the thirty-third mile- stone of the Rocky Mountain Coal Mining Institute. The Chair earnestly hopes our discussion of valuable papers which have been prepared so painstakingly by our members and friends of the Institute will assist us in the solution of problems common to our industry. The reading of the minutes will be the next order of business. For your guidance it has been customary in the past to dispense with the minutes on motion from the floor, inasmuch as the minutes are printed. May I have a motion to that effect? MR GILBERT DAVIS (Dawson, New Mexico): I move that the reading of the minutes be dispensed with. (The motion was regularly seconded, voted on and carried).

Jan 1, 1935

By S. S. Peng

In dealing with the mining engineering problems, the traditional approaches of laboratory experimental simulations and/or analytical solutions are not very effective. Mainly because the field problems are too complex to be solved with a few simplified assumptions. Conversely it is also true that the experimental and analytical/ numerical models currently available are far from being able to model the actual cases. Under such conditions, the most effective mean of research into mining engineering problems is to combine the mine (field) investigations with laboratory and / or analytical modelings. It is with this concept in mind this research was initiated in 1973. 'The field investigations which began in the fall of 1978 consisted of mainly visiting the mines where surface subsidence monitorings had been or were being monitored and/or surface structural changes had occurred. From such visits, subsidence data were collected. A quick analysis of those data provided preliminary understandings of the characteristics of the surface subsidence parameters in the regions (1-5). Using those date, models of various types are being developed for subsidence prediction / control. So far, a total of 44 longwall subsidence profiles in 22 longwall panels and 10 room-and-pillar profiles in 5 room and-pillar sections have been collected. This paper summarizes the combined results published previously (1-5) and present the preliminary results of the predictive models developed.

Jan 1, 1982

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920