Search Documents

By H. J. Seim

An ion-exchange-instrumental analysis technique is described for analyzing impurities at 1 to 1,000 parts per million level in rare-earth metals. A cation-exchange flame photometric method is used for the alkali and alkaline earth groups of metals, and an anion-exchange procedure is used in conjunction with polarographic and X-ray fluorescence techniques for selected transition elements. The standard deviation is about 6 percent, and the average error, about 5 percent.

Jan 1, 1962

It is not often that a mining district is discovered, opened up, exploited and developed into a rich producer within the space of three or four years. Not until the year 1903 was the existence of the rich cobalt-nickel arsenides and silver of Northern Ontario even suspected by the mining public. But it is worthy of record that Dr. W. G. Miller, the man who has done so much to develop sanely and honestly the mineral resources of Ontario, pointed out [ ] the possibilities of this region at least two years before the first discovery was made. . Dr. Miller, then Professor of Geology at the School of Mining, Kingston, Ont., referred in these words to the district: "It will be seen from what has been stated on preceding pages that the district examined contains as great a variety of rocks as probably any part of the Province of equal area . . . Although few discoveries of economic minerals have been made in this territory, it may reasonably be expected that deposits of value will be found when

Jan 1, 1907

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By Raja V. Ramani, Sukumar Bandopadhyay

"The dispersion of diesel contaminants into the mine atmosphere is a variant of general class of diffusion-dilution problems relevant to underground mining practice. The equipment operations in underground mining are characterized by different activities with different time duration s, i.e. varying duty cycles. Therefore the volume and quality of diesel emissions and consequently, instantaneous concentrations are quite variable. Design of mine ventilation systems under these conditions becomes complex. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport in the design of ventilation system are discussed.IntroductionThe turbulent diffusion of suspended matter in an atmosphere is not only a topic of considerable intrinsic interest to the mathematical physicist and meteorologist, but also a problem of great practical interest. Release of particulate matter into the atmosphere at large has created o ne of the acute problems of the present day. Pollution of environment by industrial and domestic smoke, fumes and grit is widespread and has necessitated extensive studies in order to determine the concentration and distribution of pollutants in various areas. Pollutants discharge from stacks, whether chemical or radioactive, give rise to similar, but more localized, problems. The laws which govern turbulent diffusion in the atmosphere are also applicable to the study of the diffusion of toxic gases and the deposition of radioactive dust from nuclear explosion.The dispersion of diesel contaminants into the mine atmosphere is but a variant of a general class of diffusion-dilution problems relevant to underground mining practice. Most of the mine air pollutants, such as respirable dust, methane, diesel exhaust, and blasting fumes are produced in the face areas and haulage ways. Understanding of their dispersion in the mine airways is important to calculate their concentrations. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport are discussed. The over-all objective of this research effort is to evaluate the impacts of dieselization on production and ventilation systems and to aid in mine planning and design, as shown in the flow model in Figure I."

Jan 1, 1983

By Okabe K

Development in the theory and practice of hearth drainage is reviewed. Difficulties in the hearth drainage were re- newed during late sixties and early seventies when the size of a blast furnace and the top pressure were increased to result in the increase in tapping rate. Hearth drainage was improved first by in- creased number of tapping and then decreased tapping rate as it was predicted by theoretical studies. State of the coke bed in the hearth, e.g., 'floating' or 'sitting-on' the hearth bottom, is discussed in relation with influential factors on it and its influence on the furnace operation. The 'sitting-on' coke bed is to be aimed at for the consistent furnace working and for the lower rate of erosion of the hearth refractory. As the continuous tapping became standard prac- tice in large blast furnaces, the interest in the basic research renewed. Prospect of the further research including mathematical modelling of the hearth drainage is discussed.

Jan 1, 1981

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1't% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the 'Super Pit'. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By Sylvie Poirier

This paper focuses on new developments regarding thermal rock fragmentation applications. The technology consists in a strong burner powered by diesel fuel and air. The thermal reaction, which is created, allows for the enlargement of 125-mm to 450-mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining. Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects, such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project. This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests realized since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described, such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed.

May 1, 2002

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By Andrew Cecala, John Organiscak, William Heitbrink

Many types of heavy equipment used in the mining and construction industries use enclosed cabs to protect equipment operators from dust and noise exposure. Normally, when the equip- [ ] ment is new, manufacturers&apos; deigned controls are effective at keeping the operator&apos;s exposure at acceptable level. However, as equipment becomes older and many components of the enclosure deteriorate, such as gaskets and seals, the effectiveness of the enclosed cab can be greatly reduced. This can cause excessive and dangerous exposures to respirable dust, especially when the ore or overburden contains crystalline silica.

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated&apos;

Jan 1, 1967

Business meeting was opened at 9:30 a.m., June 28, 1967. President James Westfield asked that the meeting come to order. "We have some business to be taken care of this morning. First, we will have a report from the Auditing Committee." Mr. W. S. Landers read the report and said that it had been audited and approved and the motion was made and seconded that it be accepted. It was accepted unanimously. (See Index for Treasurer&apos;s Report.) The Resolutions Committee Report was read by Mr. Cliff Artis as follows:

Jan 1, 1967

By R. J. Hafsten, E. S. Davenport, R. A. Grange

The influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,&apos; and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely relarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar&apos;) when the austenite grains are increased in size. More recently, Griffiths. Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745ºF. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245ºF. (675°C), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarsegrained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite—that is, at temperature levels above about 1000°F. (540°C.)—but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to he presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000ºF. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. Material and Experimental Procedure The material investigated was a cornmercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent Mo. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By Gregory M. Molinda

The U.S. underground coal miner faces a continuing hazard from the fall of roof. At the root of many injuries and fatalities are weak or defective roof strata. Throughout mining history, millions of miles of entry have provided exposure of every conceivable geologic roof hazard. This report describes the geologic origin, association, and potential danger from the most common hazards. Discussions of weak rock include drawrock, rider coals, head coal, stackrock, and stream valley effects. Discontinuities, or roof defects, are described including, clay veins, slickensides, joints, and paleochannels. A number of examples from U.S. coalfields are used to document geologic structure and associated hazards. Roof fall analysis is a methodology used by NIOSH for hazard recognition and prevention; its application and benefit to the industry are discussed.

Jan 10, 2003

By de Vries D, Wilson EG, Henderson GAM, Carter EK

Canberra is a planned city in which the natural environment, rather than existing development and land tenure, has until recent times at least, imposed the major constraints to development. Even redevelopment poses fewer problems than for most cities. Geological conditions have, therefore, played a significant role in determining its shape and layout. The Canberra experience has relevance for major new mining and engineering projects. The role of engineering geologists and geophysicists in Canberra&apos;s development is described, and the problems arising from the geological environment are illustrated by several case histories. Four aspects are addressed: pre-development urban geology; major engineering projects; resources evaluation, including groundwater; and post-development problem-solving. The Australian Capital Territory lies within the Palaeozoic Lachlan Fold Belt. Within the ACT the belt is composed of folded and faulted metasiltstones, metasandstones and acid volcanics, intruded by a major granitic pluton. Some limestone lenses occur. The region has been part of a land mass since Late Devonian times and landscape evolution has been very complex. Geological features of special geotechnical significance include deep but variable weathering, with slight to moderate weathering along faults to at least 70 metres depth in places, and consequential foundation problems; close jointing; weathered limestone lenses with solution cavities containing clay and water; confined aquifers containing artesian water in scree deposits flanking hills; the presence of pyrite; and poor quality and low volumes of groundwater.

Jan 1, 1986

By Charles L. Kimbell

World political events that occurred subsequent to yearend 1990, but that bear heavily on the global mineral industry, have been of such importance that they cannot be disregaded, and certainly they contribute to any type of "outlook." However, to write of them simply as "forecasts" in an "outlook" section of this study would be to unjustly pretend to status as prophets. Thus, this section covers events that have occurred not as predictions but rather as history. Despite the end of the cold war, the world remained fractionated, at least from the limited perspective of its mineral industry. The fractionation was not so much the result of adversarial politics between countries and groups of countries, although to be sure, such conflicts had not disappeared. Rather, the fractionation was in the widely divergent patterns of performance that resulted from the diverse conditions and problems facing the different countries and country groups.

Jan 1, 1993