Search Documents

By G. E. Anderson

The Asientos-Tepezala district is in the north of the State of Aguasca-lientes, about 30 miles north of the city of Aguascalientes, the capital. The district is reached by a standard-gage railway on the west side through the junction, Rincon de Romos, which is on the main line of the National Railways of Mexico from El Paso to Aguscalientes. The terminal is Tepezala. On the east side a narrow gage connects Asientos with the junction, San Gil, on the main line, Asientos to San Luis Potosi. Tepezala on the west side of the Asientos hills is about 2 miles from Asientos on the east side. The area between the two mining centers is separated by a low subdued divide which forms the central part of the hills. The district is in a group of isolated hills surrounded by characteristic bolsón plains. The hills rise above the surrounding plains about 6500 to 10,000 ft.; the highest peak is Alta Mira. The two mining districts lie somewhat upon the flanks of the hills at about the same elevation, 7200 ft. The district is an old one and has been known since early in the 17th Century when the mines were worked by the Franciscan Monks. Their mining operations, which were limited to the oxidized ore above the water level, consisted chiefly in extracting silver from the Santa Francisca vein. To judge from the old workings and the remains of surface plant, the operations were on a large scale. By modern mining operations since about 1900, the various mines of the district have been one of the principal sourees of ore for the smelter located at Aguascalientes. Topography The topographic features of the Asientos hills are largely controlled by the character of the underlying rocks. During the Tertiary period, the entire group of hills was probably covered by extrusive volcanic material in the form of cones and lava flows. The central part of these have since been carried away by erosion, so that remnants have been left along the borders of the hills. These remnants form rather conspicuous peaks,

Jan 1, 1927

By Moore A. J

This paper describes the use of a wavefront reinforcement model which has been developed to supplement established charge mass scaling methods. The model allows for the time taken for blast vibration wavefronts to travel from each blasthole, and has been successfully used to explain the reason for directional increases in both air and ground vibration in certain situations. The model has been used to identify wavefront reinforcement due to the propagation of air vibration and ground vibrations in certain situations. The paper includes a throw (or cast) blasting case history which provides multi-station evidence of the strong directional nature of wavefront reinforcement.

Jan 1, 1995

By Tell Ertl, Ernest E. Burgh

INTRODUCTION THE Bureau of Mines is operating an oil-shale mine 10 miles west of Rifle, Colo., as part of its Synthetic Liquid Fuels program. The purpose of operating this mine is twofold: First, to supply oil shale to an experimental processing plant; and second, to develop practices and select methods for mining oil shale on a commercial scale at the lowest practicable cost. The second purpose-that of finding out how to mine oil shale most cheaply-entails considerable mining research. Since the drilling of oil shale probably will be one of the major items of the mining cost, factors that influence drilling speeds were investigated. One phase of the drilling program was the development of a successful hard-surfaced rock-drill bit1 that can be used for drilling long holes in oil shale without changing bits. During that phase, drilling speeds were measured and drill cuttings were collected for assay and for screen sizing. When the cuttings from the individual tests were compared, a definite relationship was shown to exist between the drilling speed and the coarseness of the drill cuttings. PROCEDURE Measurement of Drilling Speeds All drilling in the tests was done with a Model UMB-D-99W Gardner-Denver wagon drill. Round-lugged drill steel, 1 ¼ in. in diameter was used in 6, 12, and 18 ft lengths with 2 1/8 -in. Timken H-type bits hard-faced with acetylene tube borium. The tests were made in the lower adit of the Bureau of Mines oil-shale mine; the grade of the oil shale drilled ranged from 18.6 to 42.7 gal per ton. During the experiments air pressure varied between 75 and 90 psi while water pressure remained fairly constant at 75 psi. All holes were drilled almost horizontally. Each drill hole was thoroughly cleaned of cuttings after being collared. The advance of the drill along the carriage was measured and recorded as the drilling speed in inches per minute. Method of Collecting Cuttings To facilitate the collection of cuttings, each drill hole was collared in a smooth, vertical portion of the oil-shale breast (Fig 1). A galvanized-steel sheet was fastened to the breast below the area in which the hole was to be drilled. The cuttings washed out of the drill hole by the drilling water were guided by the steel sheet into a wooden box. The cuttings that remained in the drill hole after the drill was withdrawn were scraped out and placed in the same box as the cuttings washed out of the hole. After the cuttings from a 1-min. drilling interval were collected, they were placed in flat metal pans. The fines were allowed to settle and the clear water was decanted. The cuttings then were dried in the sun.

Jan 1, 1947

At the Highway gold deposit, 37 kilometres south of Charters Towers, gold mineralisation occurs in several stratiform layers and is enriched near the surface by lateritic weathering. The host rocks of the mineralisation are ferruginous and baritic, intensely sericitised, kaolinised and silicified rhyolitic tuffs and pyroclastics of the Cambrian-Ordovician Mount Windsor Volcanics. The geology of the deposit is illustrated in Figures 1 and 2.Forty-six reverse circulation percussion drill holes were completed by North-Queensland Resources N.L. for a total of 2,093 metres of drilling to further outline and test the open pit resource. The drilling indicated a resource of 171,000 tonnes averaging 4.4 grams per tonne gold and 5.0 grams per tonne silver.A shallow initial pit, approximately 30 metres deep, has been designed to mine the high grade upper portion of the western stratiform layer and part of the eastern layer. This initial pit is designed to mine 45,400 tonnes of western mineralisation at an average grade of 7.84 grams per tonne gold and 22,200 tonnes of eastern mineralisation at an average grade of 1.42 grams per tonne gold. Waste is estimated at 110,900 tonnes.

Jan 1, 1986

By H. Y. Yancey, B. M. Bird

During the past four years the experimental work in coal washing carried on by the U. S. Bureau of Mines and the University of Washington has been devoted mainly to the development of special methods for the tabling of fine sizes of coals that are difficult to wash. One important outgrowth of this investigation has been the application of hindered-settling classification to coal tabling. Although used for many years in ore dressing, the term "classification" as used here may be new to many readers. It may be defined as the separation obtained when a bed of particles is held in a uniform state of suspension in an upward current of water, either continuous or pulsating, just sufficiently strong to keep the bed in a mobile condition. A common example of this type of separation is a jig in which there is no suction stroke. When the hindered-settling classifier is used with the coal-washing table, the fine-size raw coal, instead of being fed direct to tables, as is the prevailing practice, is first fed to the classifier and grouped, according to the rate of settling against the upward current of water, into perhaps six separate products. After dewatering, each of these except the sixth, a refuse product, is elevated to a seperate feed bin arid washed on a separate table. This paper gives a brief discussion of the basis for the use of hindered-settling classification of a table feed; a description of the experimental work; a comparison of the results obtained with and without classification; and a discussion of the application of the classifier in commercial coal washing. Basis for Use oF Hindered-settling Classification of Table Feed Although theoretical reasoning might be used to justify treating a table feed by hindered-settling classification,l the simplest method of demonstrating the need of such a step before tabling is to show the

Jan 1, 1930

By L. T. Sicka, H. N. Thomson

The Tooele plant of the Internationa1 Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. The copper plant has been in operation since July, 1910, arid the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 1, 1914

By Jefferson CW

Middle-to-Late Proterozoic stratigraphy and metallogeny in the eastern part of the Canadian Cordillera and in South Australia are strikingly similar. In both areas, thick, predominantly shallow-water strata and their contained mineral deposits can be divided into three sequences (A, B, C) that record episodic and prolonged continental rifting. It is proposed that Adelaidean strata of Australia were deposited adjacent to Belt-Purcell, Mackenzie Mountains and Windermere strata of the Canadian Cordillera within an epicontinental trough of a "Hudsonia" regacontinent. With the final rifting of this trough, the paleo-Pacific ocean was born. By Early Cambrian time, Australia- Antarctica was on the trailing "east" side of the nascent megacontinent, Gondwana, and was being modified on the "west" by accretion in the Pan-African event. North America, more or less surrounded by trailing edges at this time, was analogous to the Cenozoic African plate. This hypothesis accommodates the available paleomagnetic and radiometric data. It has implications for pre-Pangean plate tectonics, paleogeography, and the predictive metallogeny of both areas.

Jan 1, 1987

By Liane J. Terrill

A 9O) ft (275 meter) section of a highly fractured beam of halite was mined from the roof of a supported thirteen year old drift at the Waste Isolation Pilot Plant (WIPP). The operation was conducted with a continuous miner and allowed the unique opportunity to collect spatial information on roof beam geology and to observe ground support conditions during the mining advance. Photographs and fracture maps of the mining face document the progress of the operation and the deteriorated condition of the strata. This case study details the drift's excavation and support sequences. the geomechanical response, and the conditions found in the exposed roof beam.

Jan 1, 1997

By Gray N. B, Grimsey E. J

A steady state heat and mass balance simulation of the Western Mining Kalgoorlie Nickel Smelter (KNS) flowsheet was developed within the framework of the commercial software METSIM. The KNS simulation can achieve all plant setpoints through the adjustment of controlled process inputs, and provides a useful tool for the evaluation of the current flowsheet and potential flowsheet developments The simulation model and a number of applications are discussed in this paper.

Jan 1, 1991

By Gustavo De la Torre

El presente texto describe una serie de herramientas que optimizan los procesos unitarios en la concentradora de Cerro Lindo de compañía minera Milpo S.A.A., cuya base fundamental es el ciclo de mejora continua y productividad en general. Como primer recurso está la Geometalurgia -en tanto identifica los niveles de producción (que dependen de la dureza y moliendabilidad), la recuperación (función de la liberación de las especies mineralógicas) y la calidad del concentrado. Mientras que el segundo recurso estriba en la construcción de un diseño secundario, con el objetivo de liberar eficientemente todos los elementos de valor económico como son el cobre, plomo y zinc, Asimismo, la identificación óptima del tamaño de los valores metálicos flotables y su pronta extracción permiten optimizar la performance metalúrgica, la cual repercute en lograr mejores calidades de los productos por efectos de menor presencia de contaminantes sobremolidos y pérdidas de valore metálicos como lamas.

Oct 21, 2015

Jan 1, 1892

By B. Woyski

MANY writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deoxidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gases is more difficult to overcome. The regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes are the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer' lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere.

Jan 5, 1922

This work was instituted to investigate the microscopic structure of brown coals by means of microtome sections cut from them. It was found to be essential to impregnate the coal with some material prior to cutting, because of its powdery and crumbly nature. Of a number of impregnating materials tried, e.g., glycerine gum, gelatine, by far the most satisfactory was paraffin wax. Samples of brown coals for section cutting must be moist. When obtained, they should be put immediately into air-tight tins, and, if they are not to be used for some time, it is desirable to keep them under water containing a small amount of formalin. If the sample is allowed to dry in air, it becomes too hard to be cut. It cannot be softened again even by prolonged soaking in water.PREPARATION OF COALSmall rectangular, blocks were cut from the sample with a chisel and a strong scalpel. The largest block prepared was 3·2 x 2·5 x 0·6 cm. The faces of the block from which sections were to be cut were approximately levelled before treatment. The block was then painted carefully on all sides with two coats of warm aqueous agar, approximately 2 %. This prevented crumbling and breakage of the block during treatment. When the agar was set, the block was placed in water, and all the air removed with a vacuum pump. The water was replaced first by alcohol, then by chloroform, by the usual step transference of a series of liquids, in each of which the block was placed for 24 hours: Ethanol %, 10, 20, 30, 50, 70, 85, 95, 100 (three changes); Ethanol-chloroform, 3: 1, 1: 1, 1 : 3, chloroform pure (three changes) '. The blocks were then embedded in paraffin of melting point 56-58°C. Fresh...

Jan 1, 1947

By Mehmet F. Taner

"The East Sullivan Stock (ESS) is a small, composite felsic alkaline pluton of presumedlate Archean age in the Val d’Or mining district. Three main facies have been distinguished: mon-zonite sensu stricto, porphyritic monzonite, and green trachytic porphyry. This monzonitic group ofrocks is of relatively homogeneous composition with high abundances of Na2O, K2O, Ba, Sr, Rb, Zr,Mo and LREE. The alkaline ESS is distinguished from other igneous units in the Val d’Or miningdistrict, such as the Bourlamaque Batholith, by relatively high concentrations of Ba, Sr, Rb, Mo, Cuand Au. The ESS hosts many base (Cu, Mo) and precious (Au) metal occurrences, including: (1)porphyry style Cu-Au-Mo disseminated sulfde deposits, (2) Cu-Au deposits in volcanic rocks near the ESS contact, and (3) pyritic gold mineralization in east-west trending shear zones. The ESS is well defined by concentrical zoning on the aeromagnetic vertical gradient color map, and displays four linear trends, which are assumed to be structural lineaments, at 035°-055°, 320°-300°, east-west, and north-south. The main mineral occurrences related to the stock display a preferred spatial association with the east-west linear magnetic trends.The ESS is preferentially located along a major structure and was emplaced late in the evolutionof the Abitibi subprovince like other felsic alkaline plutons. This stock is similar to late-tectonic min-eralized felsic alkaline intrusions of the Kirkland Lake and Larder Lake mining districts in Ontario, and to the Allard stock in the U.S.A. which is associated with gold and base metal mineralization. Similarities also exist with younger alkaline plutons associated with Cu-Mo-Au porphyry deposits in the Canadian Cordillera, which formed in tensional tectonic environments. The felsic alkaline magmamay have formed by partial melting of deeply buried supracrustal rocks, concomitant with the development of deep fractures such as the Cadillac Fault. In such an environment, hydrothermal solutions carrying remobilized metals from deep supracrustal rocks may have deposited gold and base metals in structural traps. Plutons similar to the ESS should be good targets for mineral exploration. Copyright © 1996 Canadian Institute of Mining, Metallurgy and Petroleum."

Jan 1, 1996

By Pietrobon M. C, Ralston J, Smart St C R

In an on-going study of the chemistry of base metal sulphide flotation, the effect of the inclusion of cyanide in the reagents suite has been studied, with special reference to ore from Pasminco Mining's Elura mine. Cyanide has been variously described as an iron sulphide depressant, a preventor of sphalerite activation and as an activator of galena. In the case described here, the cyanide appeared to act as an enhancer of the galena flotation performance, raising the lead recoveries by 25 per cent but leaving the sphalerite and pyrite responses unaffected. The lead rougher flotation performance with and without cyanide was investigated over a wide range of redox potentials (0 mV to 400 mV SHE). In all cases, the inclusion of the cyanide brought about an increase in the galena recovery and was responsible for a faster rate of galena flotation during the initial stages of the beneficiation. A surface characterisation study (XPS) of the lead flotation stage, with and without cyanide, indicated that the reagent interacted specifically with the galena and pyrite minerals. It was possible to correlate the surface absorption of the cyanide on the lead and iron sulphides with improvements to the flotation performance using the combination of surface spectroscopy and laboratory flotation Testwork.

Jan 1, 1991

By J. Parke Channing

THESE days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," "safety," "industrial education," "efficiency," and the many other things' which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the hu¬man and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved-not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them.

Jan 3, 1915

By Etheride MA

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems an particularly prone to developing the complex fracture arrays, extreme local dilation and dramatic increases in permcahilit} that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits.

Jan 1, 1995

By Owen F. Devereux

Two discrete types of microstructure me seen in cermets formed by the reaction: 4Al (liquid) + 3SiO2 (glass) — 2A12O3(a) + 3Si (solid) Relatively coarse-grained macroscopically isotropic specimens resulted from reaction with aluminum containing appreciable silicon, while macroscopically anisotropic fine-grained specimens were formed by reaction with aluminum low in silicon. Optical microscopy, electron microscopy, and X-ray diffraction suggest that the anisotropic material contains gross areas in which submicroscopic grains of a A12O3 are oriented along radial lines drawn from the specimen surface. These lines are presumed to originate at defects in an otherwise protecting surface layer. A unique cermet is formed by the reduction of high-silica glass by molten aluminum according to the reaction: 4A1 (liquid) + 3SiO2 (glass) — 2A12O3 (a) + 3Si (solid) The free-energy change accompanying this reaction is -150 kcal at 800°C; the volume change (volume of A12O3 and silicon minus volume of SiO2) is +6 pct. The reaction product, however, contains aluminum metal as well as Al2O3 and silicon because some of the product silicon is dissolved in the aluminum bath and is replaced by aluminum in the structure. The product is a hard gray solid that retains the external dimensions of the original silica article. The system has been studied in the past, the investigations culminating in patents to George1, 2 and Saw-chuk., The former emphasize that this reaction is but one of a relatively broad class of such systems, while the latter demonstrates that a marked improvement in the gross physical properties of the cermet can be obtained by dissolving appreciable quantities of silicon in the aluminum reactant. The system has also been studied by workers at Rolls Royce Ltd.,4-6 who have patented the addition of small quantities of arsenic, antimony, bismuth, or phosphorus to the reactant bath to SO impede the reaction that glass fibers may be metal-coated by immersion in molten aluminum.

Jan 1, 1969

By Kametani H

Since pyrite is a semiconductor, the relationship between the leaching rate and the semiconducting properties is of interest. In order to investigate this relationship, a pyrite concentrate (95% FeS2) was oxidized at 90¦C (363 K) in an acid solution containing 100 g/dm3 H2SO4 and 1.0 to 25.1 g/dm3 total Fe. The suspension potential (Pt vs. SCE) was maintained at the desired values, within the range 0.40 to 0.70 V, by controlled additions of a KMn04 solution during leaching. The results were analyzed using a simplified kinetic expression. The rate constant was independent of the Fe concentration, while it increased with suspension potential. Partly oxidized samples were then prepared at varying fractions of reaction. After removing the elemental sulphur formed, they underwent thermoelectric power measurements using a packed bed lying in a temperature gradient. The value of thermo- electric power increased from about 0 to 30 pV/K in the early stages of oxidation. The results obtained are compared with those for chalco- pyrite reported in a previous paper.

Jan 1, 1987

By P J. Clark, A W. Fisher, R G. Ford

Site characterisation of subsurface contaminant transport is often hampered by a lack of knowledge of site heterogeneity and temporal variations in hydrogeochemistry. The use of a regional-scale data compilation derived from satellite imaging is discussed with respect to directing design of site characterisation to monitor the fate of a Dense Non-Aqueous Phase Liquid (DNAPL) plume in Nevada. Evaluation of the drainage basin contributing to the groundwater flux into the study site was used to re-assess the site conceptual model and re-direct the characterisation effort. The use of highly resolved measurements of subsurface hydrogeochemistry in space and time were employed to identify the predominant biogeochemical processes controlling arsenic transport during discharge of groundwater into a pond at a site in Massachusetts. Direct-push conductivity measurements coupled with vertically-resolved sampling within the pond and adjoining aquifer demonstrated spatial and temporal variations in dissolved arsenic within groundwater and the pond water column and sediment pore water. Spatial variability was observed over the scale of centimetres to metres, and temporal variations were observed over the scales of days (following storm events) to seasons. Microbially-driven redox processes maintained anoxic conditions in groundwater and at the sediment-water interface (iron and sulfate reduction) and exerted both a direct and indirect influence on arsenic solution speciation and partitioning to surface water sediments.

Jan 1, 2004