Search Documents

Executive Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEUR, Vice-Chairman. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. AUGUSTUS H. EUSTIS, Secretary, 131 State St.., Boston, Mass. The twelfth meeting of the Boston Section was held at the Engineers' Club, 2 Commonwealth Ave., Boston, on Monday evening, May 5, 1913, fifteen members and three guests being present.. The meeting Was called to order by Vice-Chairman Albert Sauveur, Who introduced the speaker of the evening, Utley Wedge, of Ardmore. Pa. Mr. Wedge read a, paper on the chloridizing roasting of copper ores, Which lie illustrated With a stereopticon, and Which will be published in full by the Institute. After Mr. Wedge had closed his paper, Which was received with great interest by all the members. the following discussion took place: Professor Hofman said that iron was formerly thought to bo essential to the Henderson process, but that it is not absolutely essential. Mr. Wedge said that., as far as he knew, the presence of some sulphates Was an absolute necessity, and that lime ores can be worked satisfactorily, although lime has an effect on the subsequent leaching. He added that the low fuel consumption of the latest Wedge furnace is a result of direct application of the combustion gases to the ore. Ten per cent. of fuel Was needed with the muffle furnace. By direct firing lie has been able to reduce the fuel needed to from 2 to 4 per cent. In the latest types of furnaces the uses from the upper hearth are not used. There is doubtless some tem-perature at Which the loss from copper chloride volatilization becomes serious, but in practice on Rio Tinto ores troublesome losses are not experienced.. The copper apparently does not become volatile at the temperatures where we would expect that it would. There are doubtless ores in which there would be serious danger from losses from this source. The latest furnaces do not use the high temperatures that Were needed in the former single-hearth Wedge furnaces.

Jan 7, 1913

By John Durkin

Field studies have been conducted in a large number of coal mines throughout the U.S. to determine the effectiveness of electromagnetic techniques in locating men trapped underground following a mine disaster. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coal fields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results indicate an expected 45% probability of detecting a miner's signal from a depth of 1,000 ft, a depth which exceeds 903 of the coal mines within the U.S. and a 90% probability at a depth of 500 ft, a depth which exceeds 50% of the mines.

By Robert F. Shurtz

When an ore deposit is evaluated on the basis of core sampling, questions always arise as to how much weight should be given the various sample grades and how the deposit should be divided into specific volumes assigned to corresponding grades. For a tabular deposit it is customary to use the so- called zone-of-influence. This zone is usually de- fined as the polygon in the plane of the deposit having corners halfway between a given core drill intersection and each of the nearest neighboring intersections. The volume of the ore in this polygon is assigned the analysis obtained from the drill core taken at the intersection. In massive or irregular deposits, volumes of various shapes may be defined with respect to the locations of drill core samples. These volumes may be regarded as three-dimensional zones-of-influence; the theory involved in assigning the values of the central analyses to the ore in the volumes is the same as that used in the case of a tabular deposit. The zone-of-influence method was used in evaluating one of the magnesite deposits at Gabbs, Nev.1-3

Jan 10, 1959

By D. W. Fuerstenau, P. C. Kapur

A new method is proposed for measuring the grindability of solids and the energy efficiency of grinding mills. The method is based on a similarity law of fracture mechanics for elastic materials in conjunction with the self- preserving character of the size distributions formed when feed particles are comminuted individually in compression. The single-particle grindability index reflects more closely the inherent resistance of a solid to size reduction than the grindability indices currently in vogue. The performance of grinding mills is evaluated in comparison with the single-particle breakage mode, which has the highest energy utilization or efficiency of all mechanical grinding routes. For a given set of stipulations, the performance index of the commonly used ball mill when grinding dolomite is found m he only 21%. compared to 44% for the high-pressure roll mill, a newly-invented energy-efficient mill. The difference is also reflected in the energy consumed per unit mass offines produced when closed-loop grinding circuits are simulated, which shows that the high-pressure roll mill circuit is invariably more energy-efficient than the ball mill circuit, provided the energy input per pass through the mill does not exceed a prescribed limit. Theoretical upper bounds on the yield of the ground product in a desired size range and lower bounds on the energy investment are calculated from the single-particle breakage mode which has, apart from the highest energy utilization efficiency, a minimum dispersion in size of the comminuted particles. Data on theoretical hounds for seven minerals/ores are presented. It is argued that it is unlikely that a grinding mill can be designed and a comminution circuit constructed whose performance exceeds these bench-mark values.

Jan 1, 1995

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

To develop a magnetic levitation transport system that can reduce the cost and improve safety in transporting coal from the face of underground coal mines to the surface. Background Many conventional mining operations use conveyor belts to transport coal from an underground face to the surface of the mine. The Mag-Lev Transport System design replaces conveyor belts with magnetically levitated coal haulage containers moving through a dedicated pipe¬line. Cost estimates, based on current design data, show the Mag-Lev Transport System would have operating and capital costs that are less than or equal to those of an equivalent-capacity conveyor belt system. The safety hazards associated with conveyor belt systems include exposure to moving parts and pinch points, potential fire hazards due to mechanical friction, and the exposure of miners to respirable dust. These hazards would be eliminated or significantly reduced by this novel technology. Approach The Mag-Lev Transport System uses magnetic levitation technology that allows noncontact, frictionless conveyance of a levitated body within a dedicated transit corridor. The mag-lev technology utilizes two types of permanent magnets coupled with an electronic position control system to achieve noncontact levitation. Levitation is provided by neodymium-iron boron (NdFeB) magnets mounted in the base of the haulage containers and inexpensive ceramic-5 magnets located in the bed of the transit corridor. An electronic position control system is used to overcome the inherent instability of the repelling permanent magnets. Proximity sensors, a signal processing circuit, electromagnetic actuators, and fixed ferrous side rails are the major components of the positioning system.

Jan 1, 1994

The program, WASTRT 70, was set up specifically to handle the design of tunnel liners and underground structures where inter- action between rock and structure significantly affects the design. It may however be used for any mass/R.C. structure capable of being simulated by straight line elements between modes and with loading restricted to nodes. The analysis system adopts typical elastic/stiffness matrix methods. Two main mass/R.C. design segments are utilized (1) Design of section depth based on maximum required stresses and optimum steel/concrete ratios. (2) Design of reinforcement for a given section depth with concrete stresses given for mass and water code structures. Each design segment covers shear, minimum principal stress on ~ , heavy compression as per code (columns), heavy compression one-face steel (tunnel liners), tension and water code requirements for all moment/thrust/section depth ratios on rectangular sections.

Jan 1, 1976

By R. W. Culbertson, S. Kasper

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons (13.6 Mt) of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past 25 years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated

Jan 1, 1980

By K. A. Hildebrant, J. R. Norgate

"Synthetic lubricants have for many years documented extended service life and provided superior performance in temperature extremes. Increasing interest in synthetics' ability to reduce energy costs has resulted in laboratory and industry application evaluations. These tests have documented savings in functions such as worm gear drives, spur gears and in compressors. Energy savings data are presented as well as payback calculations as low as thirty days.The National Research Council of Canada has estimated that the Canadian economy loses over five billion dollars per year in friction and wear. Figures quoted were for 1986 during which it was estimated that nine hundred and forty million dollars were lost in the mining industry alone"" It has been further estimated that about 115 million dollars can be immediately recovered through improved tribology practices (Table I).The purpose of this paper is to present results and savings opportunities through the use of synthetic lubricants in various but common applications. Many other areas exist with the opportunity for energy savings such as in the use of more efficient drive equipment, reduced contact seals, spray mist lubrication systems and reduced friction coatings on rotating equipment such as pump impellers"

Jan 1, 1994

By Savage E. N

Two genetic types of base metal deposits occur in the Wainivesi area of central eastern Viti Levu. The Wainivesi deposit is now considered to be a stratiform volcanogenic type, and the Wailotu and Wainiviti deposits are described as contact metasomatic with some hydrothermal manifestations. The Wainivesi mineralization is correlated with the Tertiary "e" stage, i.e. uppermost Oligocene-Iowermost Miocene. Tertiary "e" stage rocks in Fiji are therefore potential ore producers of stratiform volcanogenic type. On the basis of plate tectonics with Fiji part of the New Hebrides Arc prior to rifting apart in the late Miocene, stratiform volcanogenic deposits of the Wainivesi type may also occur in rocks of comparable type and age in the New Hebrides.

Jan 1, 1976

By Edward Walsh

In the early history of the production of metallic iron from the native oxides or ores, success attended the labors of the workman according to the care he devoted to his work, and according to the degree of skill he possessed in furnishing the required amounts of fuel and ores to be acted upon by the blast propelled by the bellows, trompe, or wooden tub, and delivered into the hearths of the Persian, bloomery, or Catalan forges. The same skill may also have been of avail in the use of the lower forms of the ".Stück," "Blue,"or" Wolf"

Jan 1, 1887

By Dennis A. Clark, Brent Larsson

Tunnelling today is a lot more than drilling and blasting. The developments in drilling and blasting technique have made it pos¬sible to save costs both by increasing the advance per round and optimizing the demands on the final contour. Increasing the hole depth by using longer feeds and bigger dril¬ling rigs make the drilling time shorter compared to the set up time. It is important that the deeper holes are followed up by using a suitable cut. The most common cut in Sweden today is a parallel hole cut with one or more large holes; with a diameter corresponding to the hole depth and wanted advance per round. It is often specified that smooth blasting is to be carried out with a specific drill hole spacing. It is extremely rare, however, for specifications to be issued concerning the alignment of the raw of holes closest to the contour holes. It is very easy to ruin the effect of smooth blasting altogether by firing the rest of the round carelessly with an excessively high charge distribution. The drilling and blasting of the contour holes and the line of holes closest to the contour holes is therefore an extremely important part of any underground work. Accuracy and care in connection with the drilling of contour holes is also extremely important since it is possible to reduce the amount of overbreak, the result being more rapid mucking out, smoother and more durable surfaces and also less consumption of concrete for lining purposes.

Jan 1, 1983

By Yagi Y

The double track railway tunnel, called the Second Shirasaka Tunnel is being constructed under the supervision of Japanese PTational Rail- ways (JNR) in the tertiary soft rock strata in order to speed up the railway transportation. This tunnel (L=1765m), located in a central part of Japan, is excavated by the machine (roadheader), while the adjoining First Shirasaka Tunnel (L=1296m), completed five years ago, was driven by the blasting, and NATM is adopted in both tunnels. The geological features in this region are Neogene Tertiary of Miocene sediments consisted of mudstone, the sandy mudstone and the alter- ation of these rocks, having a squeezing be- haviour. And the geological structure is as complicated as some anticline and syncline structures, large or small scale exist, and as a lot of faults are found. The machine excavation manner using road- header is adopted in this tunnel to minimize the effect of excavation because there is a possibility of the occurrence of landslide due to the tunnel excavation, and also because local inhabitants reside on the ground surface.

Jan 1, 1987

By Takeuchi T, Matsugaki K

We have developed a new shotcreting which is suitable for the primary support of TBM tun- nelling in soft rock. This spraying compound is made from cement, a special accelerating agent and glass fiber. It can be sprayed on to a rock surface using a specially designed gun similar to paint-spraying equipment. Some of the characteristics of this method are as follows: 1) If spraying is done keeping the distance between the gun and the rock surface be- tween 0.2 and 3.0 m, the rebound losses are small and there is little dust. 2) This method can be used on excavated rock surfaces under inflowing water conditions of up to 10 i/m2òmin. 3) After 1 day the compressive strengthes of the sprayed material is greater than 250 kgf/cm2.

Jan 1, 1987

By J. Richard Kyle

Lead-zinc ore bodies in the upper part of the Pine Point carbonate barrier complex are localized in paled-solution structures that developed as the result of post-middle Givetian subaerial exposure. Detritus-filled dolines host prismatic ore bodies, and macropores and stratabound permeable zones contain tabular ore bodies. Sulfides are concentrated in these transgressive paleosolution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition, perhaps related to periodic supply of reduced sulfur. District and ore body metal distribution pattern may reflect the nature and movement of mineralizing fluids.

Jan 1, 1981

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By J. Jordan, D. K. Denton, D. Tesarik, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health integrated the results of studies from a seismic tomographic survey, a finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. The key findings were that (1) the seismic tomograms showed that seismic velocities in rock adjacent to mine openings were low, (2) a difference tomogram in which in situ stresses on the east and west sides of the slot were compared showed that velocities increased west of the slot but decreased east of the slot, (3) geologic features (rock types and a fault) identified through geologic mapping were recognizable in the seismic tomograms, (4) ultrasonic velocity measurements on the rock cores agreed with seismic velocity measurements in the tomograms, and (5) results from a finite-difference analysis compared well to the seismic tomograms west of the slot but not east of the slot. The significance of this research is that seismic tomography is a useful tool for determining relative stress in underground pillars.

Jan 1, 2004

By C. Garcia, C. L. Lin

Characterization and analysis of multiphase particles and/or particulate systems (such as the packed particle bed) are of great technological importance for mineral processing applications. In general the performance of these applications depends on the statistical characteristics of particle microstructures, such as composition distribution, surface exposure of mineral grains, pore network structure, etc. For continued technological progress in the field of multiphase particulate processes, the need for quantitative spatial analysis of multiphase particles in three dimensions has increased sign6cantly. Such quantitative information must be accurate enough that the measured values can be used as parameters for simulation models, process design procedures, and control strategies. Modern 3D image-acquisition techniques, such as X-ray microtomography (XMT), offer a unique imaging capability that can produce high-resolution (a few micrometers) three-dimensional images of the internal structure of multiphase particulate samples. These three-dimensional image data present new challenges for image analysis, image processing, and visualization. Furthermore, important issues should focus on how to use the 3D information and derive new insights into the improvement, design, and operation of mineral processing processes. In this paper, utilization of XMT for characterization and analysis of leaching process involving multiphase particulate system is discussed.

Jan 1, 2005

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988