Search Documents

By Pinczewski WV, Nowak LP, Tanzil WBU, Jenkins DR, McCarthy MJ

An experimental and theoretical study has been made of the drainage behaviour of two-dimensional packed beds drained from an outlet in the sidewall of the bed in order to identify the fundamental me- chanisms involved. Under these conditions a grad- ient develops in the air-liquid interface in the direction of flow with the interface tilting towards the outlet. This results in a significant volume of liquid being retained in the packing on completion of draining when the interface first reaches the bed outlet. Residual liquid volume and the shape of the air-liquid interface as a function of time were det- ermined experimentally in a two-dimensional packed bed where the packing consisted of glass spheres ranging in size from 0.6 to 10 mm dia. and the bed was drained at superficial liquid velocities rang- ing from 0.007 to 0.32cm/s. The test liquids used were water, glycerine/water solutions and kerosene resulting in a viscosity range of 1 to 10 mPa.s and a surface tension range of 0.0243 to 0.072 N/m. Assuming laminar flow within the bed, a compu- tational model was developed to predict both the liquid residual ratio and the temporal evolution of the drainage profile within the bed. The computed results were in good agreement with the experimental data over the entire range of conditions invest- igated. the computational model was used to estimate the relative importance of the effects of changes in hearth conditions on residual slag volume for typ- ical blast furnace operating conditions. On the basis of the computed results it is concluded that coke quality is a major parameter affecting hearth drainage performance.

Jan 1, 1981

By Howard F. Carl

"INTRODUCTION Talc is a hydrous magnesium silicate mineral found throughout the world in deposits of economic importance. This mineral occurs in different physical forms and varying degrees of purity, both of which affect its ultimate commercial usage. Talc is used in finely ground condition by the ceramic, paint, paper, rubber, cosmetic, and other industries. Most domestic talc production is of this type. Talc also occurs, although much less frequently, in massive, fine-grained, fairly homogeneous bodies; the impure varieties are the familiar soapstones, and the purer form is frequently called ""steatite."" Because of certain properties, the purest grades of this massive variety have a monetary value about 20 times that of the ground talc.One desirable property of this massive talc is its amenability to accurate cutttng, machining, and working in many ways, similar to a hard wood or soft metal, and then firing without warping or appreciable shrinkage into a hard, refractory ceramic body. Consequently, shapes that cannot be formed conveniently by molding and pressing can be produced readily with ordinary machine tools. When talc is fired to about 1,100° C., it is converted to a ceramic body with certain very desirable physical properties. This fired material has a hardness and toughness frequently superior to steel. It is a refractory and an exceptionally good electrical insulator. When formed from a high-grade talc essentially free from iron, it has unusually low dielectric losees, even at very high frequencies."

Feb 1, 1945

A description is given of a detailed examination of a coal bore core and of attempts to predict properties of equivalent "as-mined" coal using the bore core data so obtained. The accuracy of the prediction was measured by testing independently a large sample of coal which was produced under near mining conditions from a site adjacent to the bore core. Very encouraging results were obtained particularly in the prediction of size and ash distributions and washability characteristics of run-of-mine Coal.

Jan 1, 1972

Jan 1, 1971

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By Demosthenes (Dennis) Efstratiadis

After European Council’s Directive 93/15/EEC of 5 April 1993 on the harmonization of the provisions relating to the placing on the market and supervision of explosives for civil uses, the so called ”Intra-Community Transfer of Civil Explosives” has been possible between users in the member States of the European Union. In line with this new approach, the placing on the market and the supervision of explosives for civilian use are subject to essential safety requirements. The explosives market in Italy is regulated by the ”day consumption of explosives” that imposes the user to have on site just the strict quantities of explosives and accessories that are necessary for the daily drill and blast activities. Any eventually advanced explosives’ quantities should be destroyed, either returned to the provider’s magazine until the 24:00 hours of the same day.

Jan 1, 2018

By G R. Hancock, S Grant, T Whiteside, J B. C Lowry, J Boyden, T J. Coulthard

Physically-based landform evolution models (LEM) provide a spatial framework to forecast the long-term geomorphic stability of post-mining landscapes. When used to test the relative stability of different landform designs, LEMs may assist with the development of optimal closure designs for rehabilitated mines. However, in order to reduce prediction error, factors controlling landscape evolution must also be accurately represented by models. This requires that the correct sets of processes are represented and that driving parameters used in LEMs are, if necessary, calibrated to the landscape of interest.Vegetation exerts strong controls on the hydrologic and geomorphic processes that drive landscape evolution. Hence, the spatial and temporal scales over which typical patterns in vegetation are represented in different landscapes are important considerations in LEM calibration. However, vegetation is rarely accounted for in LEMs and even when integrated is often represented simply, without representing spatial dynamics of vegetation cover that may impact landform development.This study focuses on characterising vegetation patterns to calibrate a new vegetation module of the The Cellular Automaton Evolutionary Slope and River (CAESAR)-Lisflood LEM to be applied to a conceptual rehabilitated landform of the Ranger uranium mine located in the Alligator Rivers Region (ARR) of northern Australia. In the ARR the spatial dynamics of vegetation over time are largely driven by monsoonal rains and topography. Extensive dry season fires are also common in the region, temporarily reducing vegetation cover where they occur. Hence, hydrology, topography and fire disturbance interact to shape a distinct, yet dynamic, mosaic of different vegetation types of varying cover density. As a basis for calibrating the new vegetation function, the distribution and dynamics of vegetation are characterised for this savannah landscape by remote sensing, in conjunction with ground data.CITATION:Boyden, J, Lowry, J, Coulthard, T, Whiteside, T, Hancock, G and Grant, S, 2016. Accounting for vegetation dynamics in landform evolution modelling, in Proceedings Life-of-Mine 2016 Conference , pp 63–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By Paul R. Thimas, Edward H. Boyle

"The Bureau of Mines evaluated the long-term cost and availability of primary gold production from 135 mines and deposits worldwide. Collectively, the evaluated countries represent 93 pct of world gold production. Total recoverable gold available (as of January 1984) from a subset of 111 significant producing mines and developing deposits in 13 market economy countries (MEC's) is estimated at 810 million tr oz. The Republic of South Africa is estimated to account for 87 pct of total recoverable gold. The United States and Canada account for 4 and 4.5 pct of the total, respectively. Eighty-three percent of total recoverable gold is available at a constant 1984 break-even price of $400/tr oz, and 70 pct is available at $300/tr oz. South Africa accounts for 90 pct of the gold available at $400/tr oz or less.Major conclusions are that (1) South Africa should remain the largest world producer through the year 2000, (2) annual MEC output in 2000 should not be significantly different than current output given constant 1984 gold prices of more than $300/tr oz, and (3) there may be a significant decline in production after 2010 in the absence of major new discoveries and continued development of new mines to offset the depletion of the South African mines. INTRODUCTIONSince the late 1970's the world gold mining industry has been characterized by dynamic growth in production and volatility in price. World production in 1983 was almost 15 pct greater than in 1980, and the short-term trend continues upward. Annual dollar-based price changes since the early 1970's have been unprecedented in both magnitude and volatility. This commodity, which sold for $35/tr oz3 for over a third of a century, reached an annual average $612/tr oz in 1980. Until 1980, the future price of gold seemed set on an upward trend. Since that year, however, world gold prices have fallen by over 50 pct to slightly over $300/tr oz at the end of 1984.Against this background, this study was undertaken to determine (1) the level of world demonstrated gold resources, (2) total and annual availability of gold mine production, (3) long-run production costs per operation and by national aggregates, (4) the economic and technical factors that impact upon cost and availability, and (5) probable future mine production and cost trends."

Jan 1, 1985

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By Lulie H. Crump

Salient historical data on consumption of fuels and energy have been summarized by State and census district for the years 1960 through 1972. This Information Circular covers States west of the Mississippi, and Information Circular 8704 covers States east of the Mississippi. These data replace previously published compilations of energy consumption statistics by States and districts. Future annual studies are planned using the same Btu conversion factors applied in these two Information Circulars.

Jan 1, 1976

By Zetti Gavelan, Eric Ruiz, Emilio Delgado, Ely Loayza, Jesus Cruces

La planta concentradora de minera Las Bambas logró rápidamente, y de manera sostenible, llegar a su capacidad de diseño de 140 Kton/día. Para mejorar el concepto de conminución, se inició el proceso de reducción de tamaño en el manejo de los factores de carga, diseño de mallas de perforación y diseño de voladura del macizo rocoso, debido a la variabilidad de la competitividad del yacimiento que está formado por skarn y pórfidos. Gracias a un trabajo en conjunto, la maximización del sistema de molienda SAG se consigue de manera sostenible con la integración del equipo de voladura en las optimizaciones realizadas en la planta, de manera que se logra incrementar la operación a 150 kton/día, lo que utiliza de manera eficiente la energía de la operación.

Sep 20, 2019

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By Yves Caron

Résumédes travaux effectués De septembre 2009 àmai 2011 ? Plus de 21 000 m de forages complétés en avril 2011 et près de 9 000 échantillons ? 2,7 km de décapage, 52 tranchées et 852 m de rainures ? Estiméde ressources 28 mai 2010 (SGS Géostat) ? Essais métallurgiques en laboratoire (automne 2010) ? Étude économique préliminaire (janvier 2011)

May 1, 2011

LIST OF MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES ALPHABETICALLY ARRANGED ||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal '23 ||Abarquez, Ramon F, Met, Bureau of Seience Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbort, A N , Mines Supt , Mazapil Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexieo '23 Abbott, Clarence E , Gen'l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H, Jr, Cons Min Engr 4812 W 17th St, Los Angeles, Cal '18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa '19 Abeloff, Miran S Address Wanted '21 Abernathy, G E, Kansas State Teachers College Pittsburg, Kans '20 Abey, Hiroshi, Min & Met Engr. Takata & Co, 2 Yeirakucho, Niehome, Kolimachi-ku, Tokyo, Japan '17 ||Aborn, Robert H 24 Groveland St, Auburndale, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cario, Egypt '17 Abraham, Arthur W 1828 N Alexandria Ave, Los Angeles, Cal '20 Abrahams, A. I 115 East 82nd St. New York, N Y '14 ||Abrahamson, C. Walter, Min Engr, Brule Min Co Stambaugh, Mich '21 Abrams, Charles Jackson Columbia Bldg, Spokane, Wash '21 Abrams, David H, Min Engr, S E Dickey & Co, 809-11 Johnstown Trust Bldg, Johnstown, Pa '20 Acker, E 01C, Met 128 East Washington Lane, Germantown, Philadelphia, Pa '86 Acker, William L, Diamond Drill Contractor Mears Bldg, Scranton, Pa '18 Ackerman, Ernest R, Pres Lawrenee Portland Cement Co Plainfield, Union Co, N J '15 Adachi, Jinzoo 11 Shiba Park, Shiba-Ku, Tokyo, Japan '88 Adachi, Yuich, Meeh Engr, Anzan Steel Works, Anzan, South Manchuria, China, (Via Dairen) '21

Jan 1, 1923

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015