Search Documents

By T. Kunitake, H. W. Paxton

The self-diffusion coefficient of chromium in various alloys in the iron-chromium system has been measured. A variation in Dofrom 10-4 for pure chromium to a maximum of 102 near 60 pct Cr appears with a range of activation energy from about 50 to 80 kcal per mol. The general pattern of behavior observed is not consistent with present theories of diffusion by a vacancy mechanism. Suggestions are made for further clarifying experiments. RECENT work on the self-diffusion of chromium,' ?-uranium2-4 and ß-zirconium,23, 26 has indicated that these elements have very low Do (10-3 to 10-4) compared to that conventionally expected for vacancy diffusion. Pound et al.5 have suggested that this may be due to ring diffusion being operative, and have proposed a model which gives Do of the correct order of magnitude. The essential difference between this model and Zener's earlier model6 is that whereas Zener assumes tight coupling between atoms in a ring to establish a vibrational frequency, Pound's model allows the atoms to vibrate essen- tially each in their own normal modes. The probability of each atom moving in the correct direction to cause a ring of n atoms to rotate by 2p/n must then be calculated as a "synchronal entropy" which may be -20 e.u. for a 4 atom ring. In iron, the latest determinations of self-diffusion yield Do in the range 18 to 522.7-9 The most accurate is probably that of Borg and Birchenall8 which is 118 ± 3. This value is not inconsistent with that expected for a vacancy mechanism. Since iron and chromium are very closely similar in size, are both transition metals, and their solution is thermodynamically ideal at temperatures of interest in diffusion, it appeared that a determination of self-diffusion coefficients, Do and Q as a function of composition would be of substantial interest to diffusion theory. The following measurements were made with this purpose in mind.

Jan 1, 1961

By Chung Yu Wang

During the time I was in charge of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:' "The iron ores at Tayeh * * * * lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between hornblende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende."' These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General DescriptLon of the Deposits The deposits are situated to the west of the Yangtse River, being connected with the river by a standard-gage railroad of 66 li (18.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 1, 1918

By Chung Yu Wang

DURING the time I was in charge, of this mine, from 1914 to 1915, I had occasion to read the interesting papers by T. T. Read and C. M. Weld about these deposits, to find how far their observations corroborated mine. To quote from the paper on "The Mineral Production and Resources of China" by T. T. Read:' "The iron ores at Tayeh lie along the contact between a marble and an intrusive body of a dark gray syenitic rock. * * * * At one place it is slightly magnetic, apparently having been partly reduced to the magnetic oxide by the action of reducing solutions, which have deposited small amounts of copper and iron sulphides along the foot wall." To quote from the paper on "The Tayeh Iron Ore Deposits"2 by C. M. Weld: "I find the orebodies described as occurring along an approximately E-W contact between horn-blende-granite and limestone. * * * * The granite is a granitoid rock consisting essentially of quartz, potash-feldspar and hornblende." These quotations show the differences of opinion entertained by two observers. My own study of these interesting deposits has been intermittent amid the manifold duties devolving upon a superintendent. General Description of the Deposits The deposits are situated to the west of the Yangtse River, being con¬nected with the river by a standard-gage railroad of 56 li (16.16 miles, 26 km.) in length, as shown in Fig. 1. The general topography of the region is of mature age, showing broad valleys with sluggishly meandering streams. These deposits are worked as two mines, named the Tieh Shan Mining Department and the Teh Tao Wan Mining Department; the former consisting of three orebodies more or less connected, named Tieh Man Kan, Sha Mau Tze and Lung Tung, and the latter consisting of Chang Pei Shan, Sze Tze Shan, Ta Shih Men, Yeh Chih Ping and Tsin Shan, also more or less connected, as shown in Fig. 2.

Jan 3, 1917

By M. W. Von Bernewitz

AN important regional meeting of the American Institute of Mining and Metallurgical Engineers was held, at Salt Lake City on Aug. 22 to 26, jointly with the fifth annual meeting of the Western Division of the American Mining Congress. The whole meeting was marked by enthusiasm, keen attention to the subjects under discussion, and many renewals of personal contacts. The trips to the various plants were well attended and the local press paid much attention to the meeting. The A. I. M. E. sessions began Aug. 23, with a non-technical morning session. J. 0. Elton, manager for the International Smelting Co., presided. The purpose of this session was to present in a non-technical manner the relation of flotation to mining, smelting, and the State. Ernest Gayford, metallurgist with the General En-gineering Co. of Salt Lake City, gave the definitions of flotation as suggested by Rickard, the dictionary, Weinig, and Taggart. The active agent in flotation is the air bubble, and the two prime requisites are the formation of bubbles and the creation of selective action of the bubbles for metallic particles instead of for gangue particles. Broadly, all the sulfides are floatable minerals, but the oxides, carbonates, silicates and sulfates are not. As far as Utah is concerned, flotation has been one of the greatest means of conserving its natural re-sources, because it has converted millions of tons of waste rock into pay ore; it is recovering millions of pounds of metal formerly lost in tailings; it has con-verted the zinc from a liability into an asset; and has kept thousands of men at work and distributed millions in dividends for the benefit of the State. As to the future of flotation, Mr. Gayford can con-ceive that the next 5 or 10 years may see as much, if not more, advance than was made in the preceding period. The big problem is dressing oxides, carbonates, silicates, and sulfates, and simplification of the number of reagents, also the separation of different gangue min-erals from one another.

Jan 10, 1927

By Wheeler O. North

The United Eastern Mining Co.'s property is in the Oatman, Gold Roads mining district of Mohave County, Ariz. The mine and mill are 26 mi. (41.8 km.) southwest of Kingman, the nearest railway connection. The ore consists of a mixture of calcite and quartz with some andesite. The values, which are mainly gold, alloyed with approximately 34 per cent., by weight, of silver, are extremely fine so that fine grinding is a most important factor in extraction. The milling process, briefly, consists of single-stage, coarse-crushing, two-stage ball milling in cyanide solution, followed by combined mechanical and air agitation, and by straight counter-current decantation. The Merrill zinc-dust precipitation method is used to recover the values, and is preceded by the Crowe vacuum treatment of the solution. The most notable features of the plant are the absence of filters, and the use of short peb mills loaded with steel balls, for fine grinding. As originally designed, the capacity of the mill was to be 200 tons per day, although the grinding end was to be capable of handling double that amount. By adding extra agitators and thickeners and by some alterations to the grinding end, the daily capacity has been raised to 285 tons. This, it is hoped, may be increased to 300 tons during the warm months of the present year. Tonnage Milled per Day 1917 average....... 234; maximum month.... 272; minimum month..... 146 1918 average....... 253; maximum month,... 276; minimum month..... 217 As this article primarily deals with plant operations, those interested in the mechanical description are referred to the article by Mr. Otto Wartenweiler,1 the designing engineer, which gives the details and costs of design and construction. The following changes have been made since that article was published: Two special simplex Dorr classifiers have been substituted for the two duplex Callow screens and bucket elevator, which classified the Marcy discharge and returned the oversize for regrinding. Three Dorr

Jan 1, 1920

By E. C. Harder

BAUXITE is known mainly as the ore from which aluminum is smelted but it has large use also in the manufacture of artificial abrasives and as a basis for certain chemical industries. A small amount is used for refractories and for other purposes. COMPOSITION Dana and others give the mineral formula of bauxite as A1203.2H20 and the composition as A12037 73.9 pct; H2O, 26.1 pct. It has been definitely shown, however, that bauxite does not exist as a specific mineral but rather as a rock. The term is now used synonymously with aluminum ore and it embraces gibbsite (hydrargillite or alpha trihydrate), A1203.3H20 (A12037 65.4 pct; H2O, 34.6 pct); boehmite (alpha mono¬hydrate), A1203.H20(Al203) 85 pct; H2O, 15 pct); diaspore (beta monohydrate), A1203.H2O(A12037 85 pct; H2O, 15 pct), and mixtures in various proportions of any two of them. Bauxite of the Mesozoic and Cenozoic in Europe is predominantly a mixture of gibbsite and boehmite, subordinately a mixture of boehmite and diaspore, or gibbsite and diaspore. The bauxite of North and South America, tropical Africa, Asia, and Australasia consists largely of gibbsite. Corundum (A1203) is not included under bauxite, although gradations from bauxite to emery or corundum exist. All bauxite, irrespective of the aluminum minerals composing it, contains certain impurities, including silica, in the form of clay minerals (kaolinite, halloysite, and others) or quartz, iron oxide (as hematite or goethite), titania (as leucoxene or rutile), iron sulphide (as pyrite or marcasite), iron carbonate (siderite), and calcium carbonate (as calcite); the last three mentioned in minor amount and of local occurrence only. Bauxite belongs to a group of partly consolidated materials called laterites, formed by surface weathering. This group includes also impure siliceous and ferruginous bauxite and siliceous and

Jan 1, 1949

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985

By J. H. McCormick

THIS plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor; because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyanidation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz vas sharp and, sandy, however finely ground, and rather difficult to slime. The mechanical 'equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp.,.0.68 c.; 300 to 500 lip., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower.

Jan 8, 1918

By Howard N. Eavenbon

The low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent, The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper. Geological Position of Seams The smokeless seams are among the oldest coal seams in the country, as the Pocahontas group of rocks is the lowest member of the coal-bearing series and rests on top of the Mauch Chunk red shale, in or below which no coal seams of any importance occur. The Pocahontas group, or Lower Pottsville measures, has a thickness of 750 ft. in southern McDowell County, which decreases to about 350 ft. at Prince, on the New River, in Fayette County, 50 miles to the northeast. In this group, at various points, 12 coal beds have been found, of which 4 have been found in workable thickness and are now being mined. The New River group, or Middle Pottsville measures, is just above the Pocahontas group and varies in thickness from 1300 ft. in southern McDowell County to about 700 ft. along New River. At various places, 16 beds of smokeless coal have been identified in this group, of which 5 have been found in workable thickness and are now being mined. A general columnar section of these strata is shown on Fig. 2. The workable seams in these strata, arranged in geological sequence, are as shown on page 77.

Jan 1, 1932

By Samuel B. Christy

Columbia College has the honor of founding the first well-organized School of Mines in America. The University of Michigan, however, shared with her the honor of graduating the first class, in 1867. Prof. Thomas Egleston was the pioneer in the new movement. He drew up the original plan for the Columbia School of Mines in 1863, and was in 1864 appointed its first professor. The Massachusetts Institute of Technology turned out a class of mining students a year later, and others followed in the order of their first graduating class, as shown in Table I., condensed from the Engineering News of August 11, 1892. Besides those mentioned, mining schools have been organized in the States of Arizona and Nevada, and more or less instruction is advertised in connection with other engineering schools. It will be noticed that Columbia easily heads the list with reference to the number of graduates; the Massachusetts Institute of Technology stands second ; the California University third, and then follow Lehigh, Washington University, the University of Michigan, Lafayette College, Michigan Mining School, Missouri, Colorado and the others. The total number of graduates from these 16 schools in 26 years, has been 871, or an average of 33 per year; but as all these schools give a partial education to many who do not graduate, it is probable that from 2000 to 3000 mining students have received from them considerable training. An interesting comparison of the rate of growth of the engineering schools has been recently instituted by the Engineering News, for the period between 1860 and 1892. Table 11. shows that civil engineering had the advantage in numbers from the start, and maintained the advantage until 2890, when it was surpassed by mechanical engineering. The development of the latter course may be said to date from 1880. There are many interesting facts evident in Table 11. It will

Jan 1, 1894

By D. Argyriades, G. Derge, G. M. Pound

The electrical conductance of molten FeS was studied as a function of temperature and composition. It was found that stoi-chiometric FeS (36.5 pct S) shows a minimum specific conductance of 400 ohm-1 cm-1. For the Fe-rich melts the conductivity increases with increasing amount of iron to about 4850 ohm-1' cm-I at 26 pct sulfur. For the sulfur-rich melts the conductivity increases with increasing amount of sulfur until it reaches a maximum of 1300 ohm1 cm-1 for 37.4 pct S and decreases to 800 ohm-1 cm-1 for 38.3 pct sulfur. It is concluded that molten stoichiometric FeS is an intrinsic semiconductor in which the forbidden gap in the electron energy level diagram is quite narrow. Excess sulfur acts as an acceptor impurity in providing a component of positive hole conduction, while excess iron acts as a donor impurity to increase the n-type conduction. K. Bornemann and G. von Ftauschenplatl used a four-terminal, direct-current cell to study the electrical conductance of molten copper sulfide. Their measurements showed a high conductivity, of the order of 100 ohm-1 cm-" and a positive temperature coefficient. From electrolysis studies, Savelsberg2 concluded that molten Cu2S and molten FeS are electronic conductors. Further. he found that molten FeS has a high specific conductance, of the order of 1500 ohm-' cm-', and a small negative temperature coefficient. Pound, Derge, and Osuch,3 using an ac Kelvin circuit and a four-terminal cell, measured the specific conductance of molten Cu,S, molten FeS, and various mixtures. They found that the specific conductance of the solutions followed a roughly additive rule of mixtures. Yang, Pound, and Derge4 showed from electrolysis measurements that the mechanism of electrical conduction in molten Cu2S, FeS, and mattes is primarily electronic. Further, they observed that small additions of CuCl suppress the electronic conduction whereupon the system behaves ionically.

Jan 1, 1960

By W. Rogers Wade, Alfred Wandtke

The Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) south of the international boundary and about 7 mi. (11.26 km.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the Southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The winter consists of a few days of disagreeable weather when a little snow may fall; the remainder of the year is thoroughly delightful. Vegetation is typical of a semi-arid region. In the canons near the mine, where water flows intermittently, willows thrive; on the northern slopes of some of the mountains and in some of the broader canons pines may even become abundant. The dominant rocks are flows and pyroclastics which are cut by dykes, stocks, and batholiths. The mountain just west of Nacozari is, in part, composed of limestone of an unknown age which occurs as a syncline and is undoubtedly a part of a prevolcanic land surface. Overlying the limestone and faulted against it, are the volcanics; cutting the limestone is a coarse biotite granite. Whether the granite is older or younger than the volcanics has not been definitely established. No attempt has been made to differentiate the rock types of the volcanic~, of which there are exposed 3000 ft. (914 m.) in thickness of basic and acid flows (andesites, latites, and rhyolites) and andesite and latite tuffs and breccias. The latite breccias, the youngest of these volcanic~, cover the highest mountains in the immediate vicinity. The

Jan 1, 1920

By Robert B. Parsons

"Starting January 1, 1987 employers, employees, and other taxpayers are confronted with a new set of rules dealing with the taxation of travel and housing benefits relating to isolated posts in Canada, and tax deductions relating thereto. The new rules may not be the simplest in the world, but they are reasonably fair and at least offer a hitherto unknown degree of certainty as to how such allowances are to be treated. IntroductionThe first shoe fell on February 26, 1986 when Finance Minister Michael Wilson' s first budget presented the framework for the future tax treatment of travel and housing benefits (so-called ""northern allowances"") provided to residents in remote regions of Canada. The second shoe fell some ten months later on December 22, 1986 when the Minister of Finance filled in the earlier announced framework with detailed rules. We now have a complete picture of the tax treatment of northern allowances. Here is what the picture looks like with effect from January 1, 1987.According to Revenue Canada, the net housing benefit to employees will be equal to the value of the accommodation provided, less any rent they have paid. In major centres such as Yellowknife and Whitehorse, having a developed rental housing market, the benefit amount will be based on the fair market value of the rental accommodation in that location. In other areas, employers will be required to value the housing benefits and, to assist employers, Revenue Canada has provided the following guidelines: Common shelter- $100 per month including the value of subsidized utilities Apartment! duplex-$270 per month excluding the value of subsidized utilities, or $400 per month including the value of subsidized utilities House-$450 per month excluding the value of subsidized utilities, or $650 per month in- c1uding the value of subsidized utilities.The amounts established as the values of accommodation will be adjusted annually after 1987 based on the housing component of the Consumer Price Index."

Jan 1, 1987

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By W. R. Hargrave

"Mining OperationsOre will be mined by open pit techniques. Because of the high grade of the deposit and the low strip ratio, mining rates are small relative to most other open pit operations.The ore deposit is located in the valley of the main fork of Red Dog Creek. The bulk of the deposit is located on the southwestern flank of the creek, but mineralization does traverse the creek in both the north and east directions.Erosion has exposed the orebody in a number of locations, and has resulted in oxidation of the mineralization closer to the surface. Although much of this oxide material is very high grade, it leaches readily and, at least in the initial phases of the operation, will be stockpiled and not treated in the concentrator.During construction, 2.3 million mt. (2.5 million st.) of overburden and waste will be stripped from the orebody to expose ore for initial operations. Competent non-mineralized waste will be used to build roads and waste dumps, but the bulk of material removed consists of oxide or ice-rich soils and weathered rock which is not suitable for construction.The annual ore mining rate will be 1.9 million mt. (21. million st.). The strip ratio will start off at 1.2 to 1, falling to 1.0 to 1 by year 5 and ultimately to 0.8 to 1.Bench heights are set at 7.6 m (25 ft). Pit slopes will vary depending on the material present in the wall. The slope, through competent waste and the sulphide package, was set at 45 degrees. This is flattened to 26 degrees (i.e. 2: 1) through overburden and Upper Kivalina shales. The Kivalina Shales are an ice-rich shale whose carbonate matrix has been leached out and which exhibits little or no strength as it thaws. In addition, a 100 ft containment berm will be left in the wall below overburden and Kivalina."

Jan 1, 1989

CONTENTS PAGE FOGLER, M. F., and QUINN, E. J.-Scratch and Brinell Hardness of Severely Cold-rolled Metals. Discussed by H. S. Rawdon, Carl Benedicks, M. F. Fogler, A. L.Davis 1 GREEN, C. H. Eutectic Patterns in Metallic Alloys. Discussed by Carl Benedicks, Carle R. Hayward, G. E. Dalbey, George F. Comstock, C. H. Green. 3 ARCHER, ROBERT S., and JEFFRIES, ZAY.-New Developments in High-strength Aluminum Alloys. - Discussed by F. B. Coyle, M. F. Fogler, Zay. Jeffries, D. J. McAdam, Jr., Horace C. Knerr, Ernest Schweizer 6 FLICK, FULTON B.-Etching Aluminum and Its Alloys for Macroscopic and Microscopic Examination. Discussed by Samuel Daniels 22. MERICA, PAUL D., and WALTENBERG, R. G.-The Malleability of Nickel. Discussed by H. W. Gillett, Ancel St. John. L. W. McKeehan, A. L. Feild, A. L. Davis 23 ANDERSON, ROBERT J., and NORTON, JOHN T.-X-ray Evidence Versus the Amorphous-metal Hypothesis. Discussed by Zay Jeffries, Chu Phay Yap, Francis B. Foley, H. H. Lester, Edgar C. Bain, Ancel St. John, L. W. McKeehan, Carle R. Hayward, R. P: Heuer, Jerome Alexander, Carl Benedicks 26 COOK, MAURICE, and EVANS, ULICK R.-Recrystallization and Grain Growth in Soft Metals. Discussed by M. F. Fogler 36 POLUSHKIN, E. P.-Determination of Structural Composition of Alloys by a . Metallographic Planimeter. Discussed by H. S. Rawdon 36 BASSETT, WILLIAM H., and DAVIS, C. H.-Corrosion of Copper Alloys in Sea Water. Discussed by W. B. Price, W.. R. Webster, George A. Orrok, A. E. White, William H. Bassett, D. K. Crampton 38, Scratch and Brinell Hardness of Severely Cold-rolled Metals Discussion of the paper of M. F. FOGLER and E. J. QUINN, presented at the New York Meeting, February, 1925, and issued as Paper No. 1395-E with MINING AND METALLURGY, January, 1925. H. S. RAWDON, * Washington, D. C.-We had the privilege of looking over the data just given before they were published and we were not able to suggest any convincing reason for the differences that were secured

Jan 6, 1925

By Frederick Laist

I. EXPERIMENTAL FLOTATION CONCENTRATION INTRODUCTION EARLY in 1914 it was decided to test, on a fairly large scale, the treatment by flotation of Anaconda slime and mill tailing. For this purpose a standard-type Minerals. Separation machine was installed at the Washoe Reduction Works during May and June, 1914. This was followed by the. installation of a full-size Callow pneumatic machine plant. Experiments were also made, on a smaller scale, with the Froment, the Towne, the Fields, and the Anaconda flotation machines. The last-named machine was developed at this plant. In addition to the tests made in the standard-type Minerals Separation machine some tests were made using a Minerals Separation machine of the sub-aeration type. During the series of experiments a large variety of oils was tested. Experiments were also conducted using both round-table feed and tailing to determine whether it would be better to displace the round tables by flotation for the treatment of the slime, or to supplement the round tables by flotation of the round-table tailing. A series of tests was also made on the treatment of the mill tailing by grinding followed by flotation to determine the relative merits of flotation and leaching for the treatment of this product. In addition, flotation tests were made on mixtures of mill tailing and slime. The round-table feed referred to above is the total slime from the mill. It contains about 35 per cent. colloidal solids and approximately 90 to 95 per cent. of the total solids will pass through 200 mesh (0.067 mm.). It assays from 2.3 to 2.6 per cent. Cu. The mill tailing referred to above is the total discard from the mill, exclusive of the slime. It is all finer than 2 mm. and about 90 to 95 per cent. will remain on 0.25 mm. It assays about 0.60 per cent. Cu. A brief summary of the experimental flotation results follows:

Jan 3, 1916

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month. Drilling There are in use 8 No. 44 Loomis clipper drills, caterpillar traction with gasoline engines; recently these were equipped with extra heavy stems, measuring 26 ft. overall and 4 ½ in. dia., to increase the speed of drilling. In addition, 4 No. 1 ½ G non-traction drills have been acquired, and are used to save the time of the larger drills when recleaning is necessary.

Jan 1, 1927

By Albert E. Wiggin, Frederick Laist

Early ill 1914 it was decided to test, on a fairly large scale, the treatment by flotation of Anaconda slime and mill tailing. For this purpose a standard-type Minerals Separation machine was installed at the Washoe Reduction Works during May and June, 1914. This was followed by the installation of a full-size Callow pneumatic machine plant. Experiments were also made, on a smaller scale, with the Froment, the Towne, the Fields, and the Anaconda flotation machines. The last-named machine was developed at this plant. In addition to the tests made in the standard-type Minerals Separation machine some tests were made using a Minerals Separation machine of the sub-aeration type. During the series of experiments a large variety of oils was tested. Experiments were also conducted using both round-table feed and tailing to determine whether it would be better to displace the round tables by flotation for the treatment of the slime, or to supplement the round tables by flotation of the round-table tailing. A series of tests was also made on the treatment of the mill tailing by grinding followed by flotation to determine the relative merits of flotation and leaching for the treatment of this product. In addition, flotation tests were made on mixtures of mill tailing and slime. The round-table feed referred to above is the total slime from the mill. It contains about 35 per cent. colloidal solids and approximately 90 to 95 per cent. of the total solids will pass through 200 mesh (0.067 mm.). It assays from 2.3 to 2.6 per cent. Cu. The mill tailing referred to above is the total discard from the mill, exclusive of the slime. It is all finer than 2 mm. and about 90 to 95 per cent. will remain on 0.25 mm. It assays about 0.60 per cent. Cu. A brief summary of the experimental flotation results follows:

Jan 1, 1917

The Myra Falls minesite, of Westmin Resources Limited, is located at the geographic centre of Vancouver Island, within the confines of Strathcona Provincial Park. The operation includes two active underground mines, II-W and Lynx, together with a modem 3650 1/d milling facility. Recent exploration successes will lead to the commissioning of a third mining area in late-1993 - The Battle/Gap Mine. These ore deposits are complexly metal-zoned volcanogenic massive sulphides of Devonian age, hosted in the Myra Formation of the Sicker Group volcanic assemblage. Three distinct felsic volcanic units are defined within the 450 metre thick Myra Formation. They are, from oldest to youngest, the H-W Horizon, the LMP Horizon and the Upper Rhyolite Unit. Massive sulphide mineralisation occurs throughout the property in the H-W and LMP Horizons. There are a number of orebody types, including polymetallic massive sulphides, polymetallic disseminated sulphides, zoned pyritic massive sulphides, elastic sulphide zones and stringer sulphide zones. Individual orebodies range in size from 10 000 tonne zinc-rich polymetallic lenses to the ten million tonne, zoned massive sulphide H-W main lens. The property has been in continuous operation for 26 years, producing over 13 Mt of ore averaging 2.2 g/t Au, 64.0 g/t Ag, 1.9 per cent Cu, 0.6 per cent Pb, and 5.6 per cent Zn. Current geological reserves stand at 12.5 Mt at a comparable grade, including 4 Mt of recently discovered high grade ore in the Battle and Gap Zones. Mining and milling methods have evolved over time to enable successful extraction and milling of these complex ores. Change is on-going with the recent conversion of the H-W Mine to large-scale bulk mining methods, and the development of effective computerised ore reserve calculation and mine planning tools. These changes, in concert with successful exploration techniques that led to recent high grade ore discoveries, have breathed new life into the operation and should assure its present and future viability.

Jan 1, 1993