Search Documents

By J. W. Allen

This report reviews the work performed on Task M of Bu-Mines Contract H0220073 to develop an engineering model of a surface and subsurface communications system for normal mine operations and for post disaster rescue operations. The system concept provides for one-way transmission of digital information between a number of identifiable subsurface terminals or subcenters and a single surface station. It also provides 2-way voice communications between the subcenters and the surface station. The basic communications link is electromagnetic signaling through-the-earth, but the system is also capable of using mine phone lines as an alternate link. Engineering models of three subcenters and one surface terminal (see Figure 1-1) have been fabricated in order to demonstrate the system's performance. The system concept, however, permits up to 20 subcenters to be incorporated if desired. Additional subcenters are also feasible for large mines if they can be deployed in the mine to operate on a noninterfering basis.

Jan 1, 1973

By Eugene H. Skinner

The 7-mile Flathead Tunnel, located in the central Salish Mountains of northwestern Montana, was constructed between 1966 and 1969, With the contract awarded April 19, 1966, drill and blast tunnel excavation began September 30, 1966, and was completed June 21, 1968, in 488 tunnel-driving days, Peak advance was 66 feet per day. On June 27, 1969, all tunnel concrete lining was completed. Average wall and arch concrete placing rates exceeded 1,700 cubic yards daily, with nearly half of the concrete placed during a severe winter season. Major cost savings in concrete tunnel lining were achieved through a value engineering clause in the contract. Achieving consistent results and high rates of placement in concrete lining ranked equal to ground control in overall tunnel problems. Ground control problems exceeded expectations and were of continual concern throughout excavation, One support collapse in the tunnel and one portal slide condition developed during construction. Critical surface geologic exposures were largely obscured; only a portion could be accurately projected underground, An instrumentation program to gather basic data on rock defamation near the heading face for support purposes was a pioneering effort. The Flathead Tunnel was placed in service on November 7, 1970.

Jan 1, 1974

By R. R. Sayers

The increasing use of hydrogen fluoride (annual consumption now exceeds 500,000 pounds (1)4/) directly and its occurrence as a byproduct of the utilization of fluorine compounds in the mineral industries, especially in metallurgical processes and in the refining of petroleum products, has aroused interest in its toxicity, and a brief review of the literature, with special reference to the hazard of poisoning in the mineral industries, seems to be opportune. Recently, residents in the vicinity of aluminum plants have been complaining of injury to livestock and vegetation as well as to their own health from the gases discharged into the air during operation of the plants, hydrofluoric acid gas apparently being the offender. The comparatively recent utilization of hydrofluoric acid in the alkylation process for the production of high-octane gasoline has raised the question of the hazard of poisoning in the petroleum Industry. In addition, the use of fluorine-containing refrigerants has extended the potential al exposure outside of industry (2).

Jan 1, 1945

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By Henry M. Howe

PART I. § 1. Introduction. After giving certain definitions, this paper gives the reasons which led to Roozeboom's form of the diagram of the freezing-point curves and general equilibrium of the iron-carbon compounds, steel and cast-iron ; and then those which led to replacing it with the present or double diagram, in which graphite is at all temperatures held to be the more stable and cementite the less stable (metastable) form of carbon. Next in § 10 the evidence supporting this greater stability of graphite is examined, then in § 17 that which seems to oppose it, and in § 22 a summary of the evidence is presented. The second part of the paper considers the topography of the graphite-iron diagram, rejecting summarily the solubility-lines based on the data of Charpy and Grenet and of Mannes-mann, on the ground that the data even on their face do not really point toward these lines, and that they are wholly incompetent to determine any solubility-lines whatsoever, because they report together with the dissolved carbon also an indeterminate quantity of cement-carbon, and because even such carbon as is actually dissolved, only in part represents the solubility of graphite, and in another and indeterminate part represents the solubility of cementite, or at least of carbon in presence of cementite as distinguished from graphite. It might be thought that graphite is but slightly soluble in iron, because of the absence of any suggestions of eutectoid graphite, corresponding to the eutectoid cementite of pearlite in very many cases in which the cast-iron seems to consist of ferrite and massive graphite only, and because of the micrographs of Goerens and Gutowsky. In these the primary austenite of cast-iron quenched but little below the eutectic freezing-

Jan 7, 1908

By N. A. Barcza

INFACON 7, the seventh International Ferro Alloys Congress, took place in Trondheim, Norway, in June 1995. The main aim of the Congress, which was held under the auspices of Euroalliages and the Norwegian Ferroalloy Research Organization, was to present the challenges facing the ferro-alloys industry on the road to the 21st century. Halyard Tveit, Chairman of the Technical Committee, summarized these as: ? the transition to a single global market economy ? new demands with regards to quality arising from customer needs, and ? increased awareness of the global environment. In the Plenary Sessions Kouichi Nakamura (Nippon Steel) outlined, from the steel industry's point of view, the relationship between technical advances in the products and more demanding ferro-alloy specifications. Advances in steel manufacturing technology and higher product quality have been supported in the past by raising the quality standards of ferro-alloys. Future requirements are bound to bring about more severe standards, and these need to be established by common agreement between both industries.

Jan 1, 1996

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By James A. West

Near East region countries continued to supply a large share of the world's energy requirements in 1965. The area accounted for nearly 27 percent of estimated total world crude oil output and for about 60 percent of world exports of this commodity. Also, it was the source of more than 40 percent of the world's petroleum refinery products exports. Although other mineral industry activities remained relatively in? significant in comparison with petroleum, regional production and export of certain metallic and nonmetallic mineral commodities were of world significance. Of these commodities, chief in importance were chromium, copper, mercury, antimony, boron, potash, and phosphate Tack. The Near East region contains the largest and most productive oil resources in the world. Petroleum exploration and development operations during 1965 resulted in crude oil reserve additions of almost 8 billion barrels to increase proved reserves to 219 billion barrels at yearend, an amount equal to nearly 68.5 percent of the world's proved oil reserves. Near East countries' production of crude oil averaged a record 8.337,575 barrels per day in 1965, an increase of nearly 11 percent over that of 1964. On an annual basis, Kuwait continued as the leading oil producer in the Near East; however, Saudi Ayabia was a close second and its rate of production in late 1965 exceeded that of Kuwait. The major oil producing nations and their percentage of total area crude oil output was Kuwait, 26.0; Saudi Arabia 24.3; Iran, 22.3; and Iraq 15.9.

Jan 1, 1967

By D. Harrington

The greatly extended use of the underground trolley-locomotive system for hauling coal without doubt was one of the most important factors in the rapid progress of coal mining and the increased production of coal in American coal mines during the period 1910-20. Much of the superior efficiency of production of our underground coal and metal lines should also be credited to the trolley locomotive system. The trend to mechanization of mines during the past 15 years, mere particularly the past 5 years, with higher production per man employed and greatly accelerated advancement of working places, has required increased use of trolley locomotives, necessitating larger equipment, higher speeds, and more 'frequent turn over of pit cars. This is re¬flected in increased size of locomotives and the use of larger mine ears (some with a capacity up to or over 10 tons); moreover, heavier rails and larger-size trolley wires have boon or ought to have boon installed. Trolley-locomotive haulage has proved to be rapid; economical, efficient, and productive; nevertheless; in spite of these advantages, so-many hazardous features and, unsafe conditions are involved and the price paid in life and property is so high as to justify the statement that the system should be scrapped if it cannot be operated under reasonably safe conditions. Since bare trolloy wires were introduced into underground mines, they have boon responsible for the death of hundreds of diners, property damage totaling millions of dollars, an indeterminate loss of tonnage through the abandonment of mines or parts of mines, and loss of time after disasters caused by fires or explosions originated by the trolley haulage system.

Jan 1, 1945

6889. Aslakson, C. I., and Swick, C. H. Gravity Observations in Peru and Colombia. Coast and Geodetic Survey,-Special Pub. 233, U. S. Government Printing Office, Washington, D. C., 1943, 18 pp. (Price, 10 cents.) In accordance with the policy of cooperation among American republics, the-United States Coast and Geodetic Survey in 1941 made gravity surveys in Peru and-Colombia. The information was desirable for determining the figure of the earth for geophysical purposes and for studying the relationship between intensities of gravity and deflections of the vertical. The survey instrument was the Brown pendulum apparatus. 11 gravity stations were established in Peru and 13 in Colombia. The results obtained at these stations are given in a table covering observed gravity, theoretical gravity, and anamalies. - V. S.

Jan 1, 1943

By A Van Kersen, J Hodson

Waihi Gold Mining Co Ltd [WGM], operated by Normandy Mining, has been internationally recognised for its achievements in environmental management at the Martha Mine at Waihi. In a proactive approach to dealing with community concerns regarding blast vibrations on the North Wall cutback, trials were performed using the Cardox System [Cardox], to determine feasibility of achieving economic fragmentation of andesite overburden whilst bettering management levels of 5 mm/s peak particle velocity. Cardox is a non-explosive pressure breaking system which uses high pressure CO2, Results against conventional Ammonium Nitrate/Fuel Oil [ANFO] using a variety of delays showed that conventional blasting techniques could produce marginal fragmentation within the management levels with occasional excursions, whereas Cardox produced the required fragmentation while not registering on the vibration monitoring equipment. Fragmentation to enable normal excavation by a Hitachi EXII00 hydraulic excavator was achieved with a yield of 16m3 per round. The trails indicated that fragmentation with Cardox at the yields required of over 18m3 per round was possible with further product development. The trial demonstrated that non-explosive pressure breaking is feasible and its application warranted where environmental concerns affect the cost-benefit economics of production blasting in sensitive areas.

Jan 1, 2001

By W. W. Harvey

The work to be described was part of an exploratory research program directed toward identifying potentially useful but little known reactions in extractive metallurgy. In particular, the major copper sulfide minerals, as a group, have long been considered insoluble in nonoxidizing acids (e.g. Forward and Barren, 1J60; Parsons and Ingraham, 1970; Peters et al. 1972). This generalization was considered to include nonoxidizing conditions in warm aqueous MC1 solutions (Ingraham et al. 1972) and, indeed, was consistent with our own chemical and mineralogical experience. On the other hand, under hydrothermal conditions, copper and sulfide species are carried in solution and deposited as sulfides in mineralized veins. The question that poses itself is: what are the mildest conditions of temperature and fluid composition under which commercially important copper sulfide minerals can be solubilized in the absence of an oxidizing agent? A reference to H2S formation during oxygen-sulfuric acid pressure leaching (Warren, 1958) of chalcopyrite, when the oxygen partial pressure was allowed to fall, provided a clue. In the present study, experimentation with chalcopyrite concentrate in dilute hydrochloric acid, under re flux conditions (in Pyrex flasks) and with an inert purge gas, revealed substantial amounts of H2S production and iron solubilization, cite negligible copper solubilization, after 2 ½ -4 days. Under comparable conditions the extent of reaction with dilute sulfuric, acetic and phosphoric acids was markedly less.

Jan 1, 1976

By R. L. Grayson

"Compliance standards for respirable dust, which are reduced because of high quart: concentrations, have become an industry-wide problem. Research on the physical and chemical character of quart-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quart: particles of a mine dust are ""pure,"" then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. lf, however, quart: is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.Although much research has been done on coal workers' pneumoconiosis (CWP) over the past decades, the etiologic agents of the disease still have not been pinpointed. The predominant methods of characterizing respirable coal mine dusts were bulk analysis techniques for determination of elemental and mineralogical concentrations, the results of which were used in statistical analyses to determine relationships between dust composition and the occurrence of CWP. These methods are incapable of finding the etiologic agents in the dust primarily because of complicated and confounding physiochemical factors, which may be discovered if the focus of characterization was done on a dust particle level.The SEM/EDXA-based research discussed here shows a significant difference in the number of ""pure"" quartz particles in respirable dusts collected from different mines. Some of the results have been reported previously (Grayson, Andre, and Simonyi, 1988). Concurrent research by other investigators (Wallace et al., 1989) demonstrates an SEM/EDXA-based methodology to pinpoint the location of the ""contaminating"" substance(s ) in a quartz-classified particle. The research of the European Economic Community has also begun analyses on the respirable-dust-particle level (Robock and Bauer, 1988).Since the compensatory and intangible costs of CWP are substantial in the United States, it is important that the etiologic agents be determined and then either controlled or neutralized in a cost-effective way. This line of research is especially important consid-ering the forecasted. near-term growth of coal production and the evolution of high productivity longwall panels (an immediate problem in compliance) and continuous mining sections ( a probable future problem).This need has been accentuated now that nearly all respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gem, 1986). Today a real problem exists in the coal industry, both underground and surface, because of high quartz levels in respirable dusts causing substantially reduced compliance standards (Murphy, 1989).The combined results of the respirable dust particle investigators indicate that conventional bulk sample analyses may not faithfully represent the amount of biologically available or active quartz in all mines with a high level (greater than 5% ) of quartz in the dust For example, some mine dusts might contain predominantly occluded (or coated) quartz particles where bulk analysis would result in anomalously high ""free silica"" measurements. The same result would occur when quartz particles are intermixed substantially with other minerals that can alter the surface of the composite particle away from a quartz-behaving character."

Mar 1, 1992

By W. F. Faragher

The principal equipment in the catalyst plants at Ludwigshafen-Oppau was inspected and is presented in the form of flow sheets for the manufacture of four of the principal catalysts. The equipment is in many cases of special design rather than stock items that was built by the company and modified in the coarse of the growth of the high-pressure synthesis of hydrocarbons in Germany. It is believed that if the manufacture of catalysts were to be undertaken elsewhere, the selection of equipment for the operations involved could be made successfully from the guidance furnished by this rather general report. Five additional catalysts are described, also. II. CATALYST 5058 FROM FRESH TUNGSTIC ACID In a supply tank of about 2,000 liters capacity, 500 kg. of tungstic acid (W03.H2O) that contains about 92-93 percent of W03 is dissolved at 60-70° C. in 1,500 liters of mother liquor. The solution is-effected by stirring for about 1-1/2 hours. The mother liquor is obtained from a previous, lot of catalyst and is first adjusted to a concentration of 13 percent 1H3 by passing in gaseous ammonia. The solution is allowed to stand without stirring for 1 hour, then is pumped into the saturating vessel through a cloth filter (three-quarters hr. to one hr.). The saturator is purged with H2S and thereafter the solution, which has been cooled to about 75° C., is heated in an atmosphere of hydrogen sulfide with stirring to about 70° C. This charge is slowly cooled to 50°, and then more rapidly to about 20° C. (time of cooling 6-7 hours).

Jan 1, 1946

[I-Institute of Metals Division PAUL D. MERICA, Chairman ZAY JEFFRIES, Vice-chairman W. M. CORSE, Secretary General Committee ROBERT J. ANDERSON H. C. JENNISON L. W. SPRING WILLIAN K. FRANK DAVID LEVINGER R. L. SUHL J. R. FREEMAN, JR. PAUL McKINNEY R. F. WOOD]

Jan 1, 1928

By K. Turgeon, J. -F. Boulanger, L. Whitty-Léveille, C. Bazin

"Several companies targeting Rare Earth Elements (REE) around the world have completed a Preliminary Economic Assessment showing positive project financial results. Although REE ores may contain high REE value, financing these projects remains difficult in part due to the number of processes required to valorize the elements and the relatively low yield of these processes. Direct ore leaching without the production of a concentrate may reduce the capital and some operating expenditures through process simplification, and increase revenues because of REE recovery improvement.A silicate REE ore is used to test various hypotheses regarding whole ore processing and to develop a simplified flowsheet. An atmospheric leach (200 kg/t H2SO4) of crushed whole-ore containing 0,6% REE, followed by impurity removal and REE precipitation recovers 80% of the REEs in a solution containing REE and Th. The high value contained in most REE deposits makes whole-ore approaches worth considering for most projects, given the losses of valuable species typically associated with the production of a REE mineral concentrate from the ore. INTRODUCTIONRare Earth Elements (REE) find applications in modern and clean technologies, whether civil, industrial or military. With China producing more than 90% of the world’s REE, the embargo imposed by this country in early 2010 increased REE prices for a three year period. With prices having shrunk back many-fold from their peak value, projects put forward during the hike are struggling to secure financing. Owing in part to unconventional processes such as acid-baking and solvent extraction, REE plants are high capital cost and high operating-cost units, and present technological risks (Verbaan et al., 2014)."

Jan 1, 2016

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003