Search Documents

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By R. D. Begley, A. W. Khair

Introduction The technique being investigated here uses a physical mine model which consists of a plexiglass room-and-pillar model 11.4 x 11.4 cm (4.5 x 4.5 in.). It is placed at the bottom of a larger plexiglass box 25.4 x 30.5cm (10 x 12 in.). The box is then filled with a model material representing geologic overburden. Sand has been selected because of its deformability under gravitational forces. The mine model is capable of creating a cavity and induces movement on the surface of the model material. This surface disturbance can be measured using a photographic technique called holographic interferometry. This paper discusses results of an investigation of the possibility of generating subsidence criteria using physical mine models and laser holographic interferometry. Problem Statement Subsidence appears to be widespread in two states - Pennsylvania and Illinois - although serious subsidence is found in localized areas of numerous other states (HRB Singer Inc., 1977). The US Bureau of Mines estimates that more than 1618 km2 (400,000 acres) of urban areas are threatened by subsidence. Pennsylvania and West Virginia contain 57% of these threatened areas, with the remainder being spread out over 16 states (Johnson and Miller, 1979). Events of subsidence have been reported in urban areas, including Pennsylvania (Gray et al., 1977) and Illinois (Mahar and Marino, 1981). One location has observed three episodes of subsidence beginning in 1950 (Bruhn et al., 1981). These subsidence events all occurred over abandoned room-and-pillar mines. Some mines have been abandoned more than 50 years (Bauer and Hunt,1981) . Available research does not offer much on the problem related to time dependent subsidence, especially those associated with the failure of remnant coal pillars. The physical modeling technique developed at West Virginia University is capable of measuring both instantaneous and time delayed subsidence. Laser Holographic Interferometry Laser holographic interferometry, or holometry, uses the interference properties of laser light to measure small movements of objects. The object requires only optical access and no surface instrumentation. This technique is closely related to photoelasticity. Both techniques rely on the uniqueness of the light reflected off or through an object in any given state of stress. The entire measurement process is done remotely without any surface instrumentation and without using a camera. The interferogram is constructed and visual observation will yield fringes on all areas that yielded or moved. The displacement represented by one fringe was determined by Wilson et al. (1977) and is given by the relationship: [d ='1(1) 2 cos 8 where d = displacement of one fringe 6 = incident angle of laser light A = wavelength of light (632.8 x 10-9 meters for Helium-Neon lasers)] In summary, holometry is capable of detecting very small movements of objects under study. It is a very sensitive process that requires laser light and vibration free experiments. Experimental Program Lab Facilities The primary components of the facilities were the laser and the optical table. The light source was 50 milli-watt, Helium-Neon laser. The optical table was a granite slab weighing nearly one ton. All experiments were performed on the optical table. It consists of a large table sitting on air cells similar to car innertubes. Six air cells were placed on top of two layers of wood and Styrofoam. Figure 1 is a schematic diagram of the vibration free table. Even with these precautions, the experiments still had to be performed at night to reduce potential traffic related vibrations. Room-and-pillar mine models consisting of three different pillar sizes were constructed out of plexiglass. The models were designed to represent three different extraction ratios. Figure 2 shows the models. The extraction ratios were determined by the tributary loading concept (Peng, 1978). These models were the primary component of a seam extraction simulator. A schematic of this simulation device is shown in Fig. 3.

Jan 1, 1986

The Bureau of Mineral Resources has been engaged in regional geological and geophysical field work in the Alligator River and Cobourg Peninsula area since 1971, following the discovery of major uranium deposits. Geophysical work commenced with a regional airborne magnetic and radiometric survey which was followed up by some helicopter and ground work in August 1973. The interpretation of the earlier radiometric work is presented in conjunction with the results obtained from the follow-up work. Analyses of 100 outcrop and drill core samples collected have provided basic information on the physical properties and concentrations of uranium and thorium in various rock types. The uranium determinations were made by X-ray fluorescence and delayed neutron analysis, good agreement being obtained between the two methods. X-ray fluorescence was the main analytical technique used because of its ability to produce both uranium and thorium determinations.

Jan 1, 1975

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Mining Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost-has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this exceedingly interesting subject. In the working up of the electrical arrangements touched on in this paper, the author has had the able assistance of hisfriend Mr. F. J. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer isbetter than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant.Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of regulating factors before it is possible to arrive at a proper decision.

Jan 1, 1911

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By Louis R. Iverson

Patterns of species colonization, biochemical interaction among species, and competitive phenomena were studied in four reclaimed areas in western North Dakota ranging in age from one to four years after mining, along with a site from a native mixed grass prairie for comparison. Early successional changes in floristic composition and soil chemistry were quantified. The mined sites had been contoured, topsoiled, fertilized and seeded. Despite seeding of agronomic species, initial colonization was by fugitive species; analysis of the seed bank in topsoil showed that the most dominant colonizers immigrate after topsoiling. Of the 95 species encountered, Kuchia scoparia was the most dominant in the first two years following mining. Kochlo had relatively low densities in the first year (50-80 plants m-2), but was robust and attained heights of 88 cm with a biomass of about 400 g m-2 In the second year, the plant densities increased to over 10,000 plants m"2 but the height and biomass were reduced to 15 cm and 90 g m-2. However, during the third and fourth years Kochia density declined and was practically non-existent by the fourth year, while the planted Agropyron grasses had concomitantly increased. Other pioneers like Amaran thus retroflexus, Chenopodlum album, Helianthus annuus, Salsola spp. And Setaria spp. showed a less abrupt but similar decline. Chemical analysis of the soils over the same time period showed decreases in electrical conductivity (E.C.), and in the concentrations of P, Ca, Mg, Na, Li, Sr, and SO4 (due to leaching), while N increased. Field studies were conducted on the competitive relations between the dominant species - Kochia scoparia and Agropyron spp. - during early succession. It was found the Kochia acted as a "nurse" crop for several months during the first year of Agropyron spp. establishment, but then began to shade heavily by late July, thus reducing grass tillering. Field and growth chamber experiments on the intraspecific competition relations of Kochia demonstrated that its density and dry matter production, per plant and per unit area, conformed to several laws of plant population biology. Autotoxicity or the depression in growth of a species by its own degradation compounds, in Kochia, appears to be the main factor causing the decline in its growth. Results from a field experiment indicated that thinning dense second year Kochia stands to the density of first year stands did not alter the growth of Kochia, providing strong evidence for autotoxicity. Similarly, several growth chamber experiments demonstrated that small amounts of decaying Kochia leaves and especially roots were toxic to Kochia growth, but not Melilotus officinalis or Agropyron canlnum, Chemical analysis of the soils and plant tissues indicated nutritional im¬balances as shown by P/Mn and P/Zn ratios may be responsible for autotoxicity. In addition to Kochia, a bioassay experiment showed allelochemics to be important in several other colonizing species. Although our results indicate that later stage species generally have greater toxicities than first year colonizers, autotoxicity in the very initial stages seems to be accentuated by harsh habitat conditions. Several practices (mowing. fire, etc.) are used to manage grasslands. Mowing of the first year erect, annual, colonizing vegetation was shown to be beneficial in the growth and establishment of wheatgrasses after mining in western North Dakota. Plots containing Kochio predominantly were mowed in mid-and late-July, and in mid-August, during the first year of growth after recontouring, replacing topsoil. seeding and fertilizing. It was found the Kochia densities were reduced to two percent of the control and its biomass reduced to less than one-third when the area was mowed in mid-August. On the other hand, wheatgrasses showed increases of 23% in stem density and 860% in biomass production over the controls when mowed in mid-August. The mowing of Kochia just before seed-set apparently reduces interspecific competition between Kochia and Agropyron spp. during the following growing season. The method is highly recommended for use in hastening the establishment of planted grasses.

Jan 1, 1982

By Y. Wang

Wet magnetic separation methods for recovering hematite and chromite fines and ultrafines are investigated in this paper. These methods include wet high intensity and high gradient magnetic separations, carrier or "piggy-back" magnetic method, magnetic field-induced aggregation and magnetic seeding. This investigation indicates that wet magnetic separation is more efficient for fines and ultrafines whereas other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behaviour of these minerals with respect to magnetizing field, particle size and temperature is also presented.

Jan 1, 1993

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By Henri Carrat

La Geoquímica es una ciencia que estudia la abundancia, la distribución y la migración de elementos químicos en la litósfera, hidrósfera y atmósfera. En ese sentido, el presente texto refiere los métodos utilizados en la prospección geoquímica, así como los procesos que implica. También se muestran los fenómenos desarrollados (dispersiones), métodos, el caso particular del uranio y la prospección química realizada en el C..E. A.

Jan 1, 1963

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By Louis H. Berkelhamer

"INTRODUCTION ""Free silica"" includes all free forms of silicon dioxide, such as quartz, chalcedony, tridymite, cristbbalite, opal, diatomaceous earth, and lechatelierite. The term, has been used rather loosely however, as synonymous with quartz, as quartz is the most abundant form of free silica. ""Combined silica,"" on the other hand, has been reserved to denote silica combined with other elements as silicates.Improvements in methods for the determination of free silica, and quartz in particular, have been the subject of considerable interest during the past decade, owing mainly to the accented and increased knowledge concerning quartz as a causative factor in silicosis. Analysis for quartz, however, is of importance in many other fields, including the determination of quartz in ceramic raw materials, such as feldspar and clay; the evaluation of a beneficiation procedure by the ore dresser, such as in the concentration of iron ore; control studies of a manufactured product, such as silica brick; and routine analysis of rock, mineral, and ore samples by chemists and petrographers."

Jul 1, 1944

By J. S. Brock

Magnetic, electromagnetic and gravimetric surveys have played an important role in the mineral exploration leading to the discovery of three major massive sulphide deposits in the Anvil-Vangorda area of the Yukon Territory. During 1964 and 1965 a saturation prospecting program, relying heavily on the integrated use of airborne and ground geophysical survey techniques, led to the discovery of the Faro deposit, which was subsequently proven to be a 63-millionton lead-zinc orebody. Locating the Faro deposit, the largest found to date in this overburden-covered region, involved an exploration sequence requiring the selection of a favourable geologic environment, aeromagnetic and electromagnetic surveys, property acquisition of anomalous areas and detailed ground geophysical surveys, followed by rotary drill testing, detailed gravimetric surveys and diamond core drilling.

Jan 1, 1973

By J. Ivon Graham, T. D. Jones

This paper presents methods in use in British coal-mines for the suppression of dust. While the effect of present-day treatment will not be apparent for several years, in pits in South Wales, concentrations as high as 50 gm./1,000 cu. ft. were some years ago fairly common in various operations at or near the coal-face, with an average concentration of 20 gm./1,000 cu. ft. Now the average concentration in what were previously dusty pits is probably not greater than 3 gm./1,000 cu. ft.Nevertheless, every effort must be made to improve conditions still further. In South Wales it is claimed that 99% of the coal-faces requiring treatment have been dealt with either by wet cutting, infusion, or hand-spraying. The extent of the treatment by these methods can be gauged by the fact that the total length of coal-faces now being treated by water infusion in Cardiff and Swansea areas is about 33,000 yds., by wet cutting 25,000 yds., and by hand-spraying nearly 14,000 yds. The influence of methods of mining upon dust production is only mentioned very briefly in this review, and there is no doubt that much more is to be learned concerning this aspect. It can be stated, however, that good mining practice is essential to prevent unnecessary dust production, and the problem of dust in mines will be solved only by the closest co-operation between mine managers, workmen, and scientists.

Jan 1, 1947

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945