Search Documents

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009

By G. Danha, D. Glasser, D. Hildebrandt, N. Hlabangana

"In this work, we apply a method known as the attainable region (AR) technique in order to optimize the milling and leaching process of a low grade gold ore. No work on the application of the AR optimization technique has been done yet on a joint milling and leaching process. The advantage of the AR approach lies in its ability to simplify the optimization problem, as searching over a defined set for the maximum of an objective function is a fairly standard procedure. The objective function we selected was that of optimizing a linear function of the value of the recovered material minus the cost of both milling and leaching. Using the three variables (milling time, leaching time and recovery), we constructed a 3D plot and used it to obtain all the possible recoveries from the different milling and leaching times. The optimum for our chosen objective was then found by overlaying a contour plot of the objective function on the 3D plot. Our results show that the optimum was obtained at 90 % recovery with a profit value of 600, milling time of 30 minutes and leaching time of 1750 minutes.INTRODUCTIONAfrican countries are facing a general increase in demand for electrical power. In South Africa, the demand is now surpassing the supply from ESKOM, the main electric power provider of the country. This has resulted in load shedding strategies being implemented in many local communities in an attempt by ESKOM to cope with the high demand. A potentially better approach is to propose use of energy efficient technologies in the country’s largest power consuming industry; the mineral processing sector.In mineral processing, milling is the highest consumer of energy. The objective of carrying out milling is not merely to reduce the particle size of the feed material, but also to liberate the constituent minerals that make up an ore. This is done so that valuable minerals can be separated from the gangue, in downstream processes, such as leaching. However, the milling process is generally performed relatively poorly, and at a considerable expense in terms of electrical power utilization. Tomanec and Milovanovic (1994) estimated that milling accounts for more than 50 % of the total power used in the concentration process, but this can rise to as high as 70 % for hard or finely dispersed and inter-grown ores. Apart from being relatively wasteful of energy, the milling process is also inefficient with regard to mineral liberation because of the indiscriminate nature of the grinding force."

Jan 1, 2016

By W. G. Pariseau

"BACKGROUND Strata mechanics of three underground coal mines in central Utah were recently studied using a specialized finite element technique [1, 2, 3, 4]. The purpose of these studies was to examine relationships between mining and related seismicity. The longwall mining method was predominant, but room and pillar mining and barrier pillar mining were also used in the mines studied. In every case, high correlation between face advance and seismicity was observed. The specialized finite element technique allows for whole mine subsidence estimation at a kilometer scale and for stress concentration at a meter scale near a working face. Comparisons of observed mine subsidence with model subsidence allows for model verification and justifies detailed analysis of the evolution of stress at seam level. Yielding is expected near a longwall panel face and as the face is advanced the extent of yielding is expected to increase. The total number of element failures in a finite element mine model also increases, so a high correlation with associated seismicity, say, event count, is not so surprising. A brief review of recent coal mine studies in Utah is presented in the sequel. The procedures are given in some detail in application to trona mining. COAL MINES The analysis procedure begins with the geologic column and proceeds to specification of strata properties including elastic moduli and strengths. Joints are an integral part of the geologic model and joint set specifications include dip direction, dip, spacing, stiffness and strength. Spatial variability of strata properties in situ may be taken into account during analysis. Topography is important, especially to Utah coal mines that are developed from outcrop in regions of high relief. Mesh generation follows specification of data input. Finite element analysis is next, followed by reporting of results. In this regard, all finite element computations are based on first principles. No model “calibration” is done that involves adjusting computer input to obtain a fit to mine measurements such as subsidence profiles. Figure 1 illustrates the concept of a dual node – dual mesh finite element concept. Dual nodes are roof and floor nodes in mined areas. These nodes replace the seam. The dual mesh is a much refined mesh with displacement boundary conditions obtained from the big mesh and thus replaces the effect of mining in the region outside the dual mesh. The refined dual mesh allows for details of stress, strain and displacement near a working face of interest. Strata Properties Strata properties include elastic moduli and strengths of intact rock between joints and joint stiffness and strength for each joint set present. Both properties sets may be obtained from laboratory test data, although testing joints poses a sampling problem in the field. The statistical variability observed in laboratory test data, say, in unconfined compressive strength tests is often characterized by much variation. In fact, the coefficient of variation, ratio of standard deviation to mean, is often greater than 35 percent. When sample values are mapped back to the mine location, one may observe spatial variability as properties vary from place to place as shown in Figure 2. Spatial variability may be incorporated into a finite element analysis with probabilistic assignment of properties to elements in accordance with measured variability. The result is a more realistic model of rock in situ."

Jan 1, 2017

By Wayne W. Murdy

Peru is a mineral hot spot in the world today. Newmont is in the exploratory phase of this mining cycle, a phase full of optimism and expectations. But exploration is high risk. There will be successes but also failures. Many foreign companies will come and go. But it is the responsibility of the mining industry leadership of Peru and the government to continue to foster an environment conducive to investment. This is the time of year companies begin planning their next annual report. Last year, Newmont’s was called “new horizons.” It highlighted the company’s global expansion into Peru, Uzbekistan and Indonesia. Now, projects that were only on the horizon a year ago are moving into production. So “turning opportunity into gold” may be this year’s theme.

Jan 1, 1996

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By Marius R. Campbell

VARIOUS classes of coals are recognized in this country at the present time. These classes depend largely upon physical characteristics rather than upon chemical composition, and consequently they cannot be accurately defined. The divisions into anthracite, semi-anthracite and semi-bituminous are fairly satisfactory; but the term bituminous embraces so large a variety of coal that it is of little value, and the term lignite is so loosely applied that it has little or no place in a scientific classification. At present there is no way of accurately defining the vari¬ous classes of coal, because no adequate scheme of classification, which applies to lignites as well as bituminous coal and anthracite bas been proposed. The object of this paper is to present such a scheme, which is based upon data obtained dur¬ing the past year by Prof. N. W. Lord,1 in charge of the chemical laboratory of the United States Geological Survey coal-testing plant at the Louisiana Purchase Exposition, St. Louis. All the classifications of coals proposed prior to 1877 were based either on physical characteristics or on proximate analyses, including all of the impurities. These schemes were illogical and highly unsatisfactory, for the physical properties of a coal give little indication of its true composition; and impurities, such as ash and sulphur, are largely the results of acci-

Sep 1, 1905

By R. S. Jurani

Sunshine Mining Co.'s Kellogg operation is the primary silver producer in the US. Maintaining a comfortable working environment in this deep underground mine historically has been a complex and costly problem. To improve the ventilation and cooling systems at a time of declining and un-certain silver markets, it was proposed to optimize the performance of existing facilities at minimum cost. This paper discusses a two-year, $400,000 optimization program that resulted in increased total mine airflow, cooler ambient temperatures, reduced compressed air usage, and lower energy consumption by primary fans, air compressors, and refrigeration plants. This saved the company about $650,000 per year.

Jan 1, 1988

By Onder Guney, Erdem Demirkesenm

"In this study, the crystallization behavior and thermal expansion coefficient of a lithium disilicate (LS2) based glass-ceramic derived from SiO2-Li02-AhO3-K2O-ZrO2 system was investigated by using x-ray diffraction (XRD), high temperature x-ray diffraction (HTXRD), differential thermal analysis (DTA) and dilatometer techniques. Analytical reagent grade chemicals were chosen as raw materials for preparing glass batches. Nucleation and crystal growth heat treatments were planned according to DTA results. The amounts of the amorphous and crystalline phases developed during the heat treatments were determined by quantitative XRD. XRD results of crystallized samples showed simultaneous formation of lithium silicate (LS) and quartz in the early stage of the crystallization followed by formation of lithium disilicate (LS2) at higher temperatures. The thermal expansion coefficients of glassceramics were also measured depending on the applied heat treatments.IntroductionSignificant developments occurred in all ceramic materials provide the fabrication of high quality dental implants [1]. Glass ceramic based dental restorations like dental inlays, crowns, bridges and veneers are becoming increasingly popular with their reliable and durable performance [2,3]. In addition to their advanced functional properties, glass ceramic implants especially lithium disilicate glass ceramics also face the esthetics expectations of patients and dentists and in this way they are starting to take the place of metal based restorations today [1,3,4,5]. Lithium disilicate glass-ceramics derived from multicomponent glass systems have some superior mechanical and optical properties comparable to natural teeth [ 6]. In restorative dentistry, mechanical characteristics of biomaterials play very crucial role in order to resist the masticatory forces occurred during biting and chewing [7] According to three point bending test results of Roland, flexural strength of the lithium disilicate glass-ceramics were 400±40 MPa and their fracture toughness (K1c) are approximately 3,3 MPa m112 [2,6]. In addition to high mechanical strength, aesthetic appearance is another important prerequisite as material for dental restorative applications. Translucency and light transmission of the LS2 glass ceramics mimic enamel. Moreover, opacity of the material can also be adjusted depending on the restoration types [2,6, 7]. These superior properties of the LS2 glass ceramics are directly related with chemical composition of the base glasses and controlled crystallization heat treatments [ 4, 7]. The aim of the present work is to determine the effect of heat treatment schedules on the crystallization behavior and thermal expansion of the LS2 glass-ceramics."

Jan 1, 2011

Jan 1, 1962

Slide presentation at conference

Jan 1, 1996

By Ralph van Rijswick, Erik Vlot

"Anglo American operates 18 Weir GEHO piston diaphragm pumps (PD) in the two pump stations of the 52-km (32-mile) long Minas Rio iron ore concentrate pipeline. The pipeline is designed to transport 26.5 Mt/a (29.2 million stpy) of concentrate from the mine to the export terminal at the coast.During the commissioning of the pipeline in the fall of 2014, high pressure pulsation levels were experienced, with peak-to-peak levels as high as 20 bar. Based on pressure readings it was concluded that hydraulic resonances were present in the system, which were excited by the third and sixth harmonic of the flow pulsation generated by the pumps.Based on this observation, Weir Minerals Netherlands, manufacturer of GEHO PD slurry pumps, recommended installing a phase shift controller that controls the phase shift between the crankshafts of the individual pumps, thereby minimizing the effect of the hydraulic resonances.GEHO piston diaphragm pumps and pressure pulsation analysisPiston diaphragm pumps are used worldwide to transport abrasive and/or aggressive slurries against high discharge pressures in the mining, mineral processing and power industries. The basic operating principle of a piston diaphragm pump is shown in Fig. 1.A crankshaft is driven by an external electric motor via a gearbox. The crank mechanism transfers the rotating motion of the crankshaft into a reciprocating motion of the piston. The piston displaces a hydraulic fluid, called the propeling liquid, which displaces an elastic rubber diaphragm. When the piston moves to the right, the pressure in the pump chamber drops below the suction pressure and the nonreturn valve on the suction side will open, allowing the pumped fluid to flow into the pump chamber. When the piston moves to the left, the fluid is compressed, and when the pump chamber pressure rises above the pipeline pressure, the nonreturn valve on the discharge side will open allowing a displacement of fluid into the discharge line. The main objective of the diaphragm is to isolate the piston and the drive mechanism from the abrasive and/or aggressive fluid and create a hermetic seal between the pumped fluid and the ambient environment. Piston diaphragm pumps as shown in Fig. 1 are among the largest positive displacement pumps in the world and have been produced with stroke volumes of up to 100 L (26 gal) per pump chamber for flow rates up to 800 m3/h, discharge pressures up to 250 bar and hydraulic outputs over 2 MW per unit (van Rijswick et al., 2010)."

Jan 9, 2017

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By C. L. Reichardt

"Pressure exerted on gold producers by regulators, project financiers, and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport, and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ‘cradle to grave’ approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or on the receiving environment, either during mine life or after closure.Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill. Certain principles of the Code also pertain to aspects of operations, worker safety, emergency response, training, and dialogue with stakeholders relating to backfilling practice.For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce."

Jan 1, 2007

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By Igor Gonzales G.

The Southern Peru Copper Corp. (SPCC) recently built an integrated copper project consisting of dump- and heap-leaching operations at its mine complex in Peru. The pregnant leach solution (PLS) containing the solubilized copper from the leaching operations is processed in a new solvent extraction/electrowinning (SX/EW) facility to produce high-purity cathode copper. The dump leaching and SX/EW facilities are located near the Toquepala mine site. The crushing and heap-leaching operation is located at the Cuajone Mine. The pregnant leach solution from Toquepala and Cuajone is pumped 35 km (22 miles) to the SX/EW plant at Toquepala. The SX/EW plant consists of three trains of solvent extraction (SX), a tank farm area and an electrowinning (EW) facility. The solvent extraction plant has a total PLS flow capacity of 3,210 m3/hr (113,360 cu ft/hr). The electrowinning facility has an expected long-term production capacity of 97 t/d(107 stpd) or about 35 kt/a (38,500 stpy) of cathode copper. However, present production exceeds the expected long-term by about 20%.

Jan 1, 1996

By J. D. de V. Louw

Introduction Zircon is a natural occurring mineral and may exhibit natural low level radioactivity. It contains trace levels (90 to120 pCi/g and 110 to 115 pCi/g respectively or 3.3 to 4.4Bq/g and 4.1 to 4.3 Bq/g) of naturally occurring radioactive uranium and thorium. This mineral is often found in a suiteof minerals (rutile, ilmenite and monazite) Due to the overlap in physical properties of monazite (containing 4–7% thorium) with some of the zircon (slight magnetic susceptibility) it often contaminates the zircon, adding to the levels of thorium in the product. Hazards associated with the products from zircon and its processing is inhalation of respirable dust (generated by milling) containing radioactive uranium and thorium which may cause cancer of the lungs. Legislature regulates the transport, use, workplace environment exposure and storage of radioactive material. In America the general regulation for the unlicensed use of low levels of radioactive materials limits the concentration to 500 ppm (U plus Th). Europe (IAEA) specifies a limit of10 Bg/g (Bequerels per gram) on the parents for transport only which is a higher level of U+Th. Companies selling into these markets need to comply with these regulations and certification is therefore required, not only of the major constituents determining the price, but of the U and Th levels as well. Exceeding the limits for U and Th may result in material being returned to the country of origin. However, for the analyst the requirement is to analyse for these elements throughout the production process as well as the analysis of the ‘tails’ that is returned to the mine area. This requires a wide range of concentration to be analysed. Methods of analysis A wide variety of methods exist for the analysis of U and Th in a range of matrices. (Table I) All these methods have been used with varying degrees of success in terms of accuracy. Overall precision for the different techniques varies from 5 to 25% relative. Time to produce results from these methods vary from a few minutes to several days. The Production Chemist is expected to produce between5 and 10 analyses per hour for process control purposes. A suitable technique that fits this requirement is X-Ray Fluorescence. Both Wavelength Dispersive (WDXRF) and Energy Dispersive X-Ray (EDX) instruments are suitable. X-Ray analysis in general has a few major advantages over competitive techniques. •It is fairly simple to set up and interferences are known and easy to correct •It has multi-element analysis capabilities •Clean spectral lines for U and Th (in zircon specifically) •Uncomplicated and easy to measure background •Low detection limits (3 to 5 ppm) •A very high degree of precision •Sample preparation is uncomplicated and fast (pressed powders and fused beads). In Zircon (ZrSiO4) processed sands the matrix is constant(>99% ZrSiO4) and the background is thus essentially constant. A typical set up for the analysis of U and Th by WDXRFis given below: X-Ray Tube Tungsten (W) Target, 2.5 to 3kW operated at 50mA/50kV Crystal LiF200 (or LIF220 for higher resolution) Analytical Lines (2?)U La1,226.14Th La1,227.47 Detector Scintillation Counter Analysis time, depending on the concentration can vary from as little as 20 seconds up to 5 minutes. Standards As with any other comparative technique XRF analysis relies heavily on the quality of the standards used. Assuming proper set-up and operation of the instrumentation as well as consistent sample preparation, accuracy is determined by the quality of the initial calibration standards. A search for the available zircon certified reference materials (CRMs) shows that there are only a few CRMs

Jan 1, 2003

By H. Conrad, K. Jung

"The effect of an external electric field E=5(+) kV/cm applied during the solution heat treatment at 500°-550°C of three commercial Al-Mg-Si alloys (AA6061, AA6022 and AA61l1) on the asquenched resistivity Pw and hardness H.,NULL, w was investigated. It was found that the field gave a significant increase in Pw and in Hv,w, for AA6022 and AA6111, but had no clear effect on AA6061. Thermodynamic analysis gave that the effect of the field on AA6022 and AA6111 was to reduce both the enthalpy ?H, and entropy ?H, of solution. Considering the chemical composition of the three alloys it appears that the influence of the field may depend on the amount of Cu plus excess Si present in the alloy.IntroductionKlypin and Soloviev [1, 2] were the first to report that the application of an external electric field during solution heat treatment (SHT) of Al alloys gave an increase in the as-quenched resistivity and hardness. They attributed these effects of the field to an increase in solubility of the alloying constituents during the SHT. More recently Liu and coworkers [3, 4] also reported an increase in the as-quenched resistivity of Al-Li alloys with application of an electric field during SHT. Further, the present authors [5] found that the application of an electric field during the SHT of the commercial Al-Mg-Si alloys AA6022 and AA61i1 increased their as-quenched resistivity and hardness. Their thermodynamic analysis of the results indicated that the field decreased both the enthalpy ?H, and entropy ?S, of solution."

Jan 1, 2004

By Katsumi Ogi, Hiroto Uchida, Masamitsu Sato, Atsushi Itsuki

"(BTMSE)Ag(hfac) (BTMSE = trans-bis(trimethylsilyl)ethene) was chosen as a suitable precursor for the XeCl laser (308nm) MOCVD of Ag. Iso-propanol solution of (BTMSE)Ag(hfac) was used as a liquid source for the liquid delivery method, high deposition rate 9nm/min at substrate temperatures of 100°C and 120°C were obtained at the vaporizer temperature of 90°C. This deposition rate is three times faster than by conventional bubbling method and life of the source and reproducibility of the deposition were also improved. Electric resistivities of the laser deposited film shows significantly low resistivity of 10-6Q-cm compared to 1 o-3Q-cm of thermal MOCVD film. These results indicates that the laser MOCVD is one of the effective method for the preparation of the high quality silver film.IntroductionSilver films are a potentially important metallization material in electronic and photonic devises due to their lowest resistivity (1.6µ0-cm) among the metals, high optical reflectance and chemical stability. The MOCVD technique has advantages to sputtering or evaporation in the point of conformal growth and better coverage on sharp steps and narrow gaps[l-2]. For MOCVD application, silver precursors must have sufficient vapor pressure without decomposition at their evaporation temperature. To achieve stable precursor gas supply, liquid delivery of precursor material is promising[3-4] especially for materials that have not enough heat stability and high vapor pressure like silver complexes[S-10]. Several new silver complexes for MOCVD and UV irradiation effect to their MOCVD silver film quality were reported by same authors[5]. In this paper new solvent system for liquid delivery system of silver MOCVD were investigated to suite XeCl(308nm) laser MOCVD application."

Jan 1, 1998