Search Documents

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By Cary Hirner, David Stacey, William A. Rochford

Design considerations and construction techniques were implemented to address groundwater infiltration from a confined aquifer during the excavation and lining of the Cady Marsh Flood Relief Tunnel. This 3-m finished diameter, 2-km long tunnel was successfully completed cost-effectively in an urban setting near East Chicago, Indiana. The soft ground was mined using a conventional tunnel boring machine with hydraulically actuated flood doors and supported with steel ribs and timber lagging. The tunnel was lined with cast-in-place concrete. Dewatering was implemented in settlement prone, boulder-laden ground in residential neighborhoods during construction to depressurize and partially dewater the aquifer at the tunnel horizon. This paper describes the design decisions and construction methods utilized to mitigate and limit infiltration into the tunnel during construction and operation, as well as manage ground settlement.

Jan 1, 2007

By A J. Broome

Since 2003, there has been an unprecedented growth in the demand for engineering, technical and project services in the mineral industries. This demand for services became evident in Australia earlier than many other markets and has since spread globally. This growth has created significant issues for the strategic direction and planning by the service provider. Such strategic questions include:- how fast to grow, how to recruit, train and integrate new staff, what market sectors to service, the selection of targeted customer sectors and managing strategic growth with short term demands and commercial reality. These factors are discussed using in depth experiences and examples that illustrate these strategic approaches. The relevance of this new industry environment to New Zealand services will be highly discussed.

Jan 1, 2007

By P. Mokwena

Paper written on project work carried out in partial fulfilment of BSc (Hons) in Chemical Engineering Diamond synthesis has attracted a great deal of interest because of its exceptional properties and various applications. In this study, the chemical catalytic vapour deposition (CCVD) method was used to synthesize diamond films using acetylene as carbon source and hydrogen as carrier gas at a temperature of 1000°C, and their thermodynamic stability was studied. Photographic analysis revealed that these products are diamond films, Ramman spectroscopy confirmed that they are graphitic while confocal laser scanning microscopic image analyses proved that these diamonds films have structural defects due to iron impurity from the catalyst precursor. The quantity of diamonds films produced is also proportional to the acetylene to hydrogen ratio but these films are larger in size at lower acetylene to hydrogen ratio. Thermogravimetric analyses showed that transformation of these materials begins at 25°C but could not be used to determine if a temperature range below 25°C exists. The stability of these CCVD-synthesized diamonds also increases below 25°C when stored at different temperatures.

Jan 1, 2007

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By A. Rahimi

Refractory castables based on alumina-silicate aggregates are commonly used in casting wheel components and launders. In this research the recycling process of waste magnesia chrome bricks for production of refractory castable lining for launders and casting wheel ladles at Iranian Sarcheshmeh copper complex (I.S.C.C.) is discussed. The smelting plant of ISCC consumes 4,000 tons refractory materials and produces 2,000 tons waste refractories annually. In order to reduce the environmental pollutions and gain the economical advantages, the recycling of waste refractories proved to be a solution [1]. In ISCC, 800 tons alumina or alumina-silicate refractory castables are used for linings of anode furnace ladles and launders annually [2]. In the present work, the spent bricks from reverberatory, converter and anode furnaces were analyzed in term of microstructural changes from hot zone to the cold end to evaluate the changes in texture and chemical composition. Different formulations based on recycled magnesia chrome aggregates and various particle size distribution and cement content were tested. Economic recycled magnesia chrome refractory mixture was prepared after crushing and sizing the non-deteriorated regions of wasted bricks. After evaluation of physical and mechanical properties of samples, one ton of refractory castable was prepared and successfully installed in the casting wheel ladles.

Jan 1, 2007

By William M. Gleason

Hard times continued to plague the industry when the calendar rolled over to 2000. During 1999, the United States economy had grown vigorously, capping the longest economic expansion in United States history. However, the mining industry was not so fortunate. Commodity prices remained in a slump in the “new-economy” that was fueled by excitement and speculation about the power of the Internet during the infancy of the Information Age. Much of the investment money that once went to mining and exploration was now headed to the world of virtual gold mines. SME President Donald E. Ranta implemented new technology into his plans for SME. His two major goals were new membership growth and to foster the establishment of the comprehensive Internet presence for the Society’s technical information. His strategic priorities included enhancing the quality and quantity of publications, programs, meetings and short courses. “The Internet is the vehicle that will advance the priorities,” he said.

Jan 1, 2007

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By Z. Jun, L. Kerning

Jinlong copper smelter and refinery, originally designed for 100,000tpa primary copper and started up in 1997, has been expanding its capacity on the basis of operational optimization and by modifying its facilities. Currently it is producing 210,000tpa primary copper, and the new phase of expansion project with a target capacity of 350,000tpa primary copper is ongoing. This paper reviews problems and improvements made with operation and equipment in the past years. Recent plant operation is briefly described. The expansion projects completed are summarized and the ongoing expansion project is present.

Jan 1, 2007

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By Robert Hopler

In the annual report under the Explosives Act for 1905, H.M.inspectors state that over 90 percent of the accidents causing death or personal injury occurred in the use of explosives and under miscellaneous conditions to which the controlling provisions of the Act do not apply, and that such accidents caused 43 out of the 50 deaths, and 312 out of 348 cases of injury. The number of accidents grouped under the heading of “Use and Miscellaneous” is less than that for 1904 - viz., 281 against 301. By these accidents 43 persons were killed and 312 injured, as compared with 39 killed and 343 injured in 1904

Jan 1, 2007

By A. Koski

A pond rehabilitation and environmental education project were proposed by Cleveland-Cliffs Michigan Operations (CCMO) and approved by the Michigan Department of Environmental Quality (MDEQ) and the United States Environmental Protection Agency (USEPA) as partial fulfillment of conditions for a stream mitigation permit. The goals of the project were the rehabilitation of a pond on a tributary of a local trout stream, enhancement of public access and appreciation, and the initiation of a site-based environmental educational curriculum. Cleveland-Cliffs undertook a suite of actions to rehabilitate a pond created by a previous mining operation in 1912 and make accessible to local schools the aquatic and riparian ecosystems. Cleveland-Cliffs partnered with the local governmental unit and two local school districts. The rehabilitated pond and riparian zone provide an accessible natural area that local residents can use for such activities as hiking, biking, walking, fishing and nature study. Vegetative enhancement includes the planting of native shrubs, wildflowers and showy herbaceous plants in the pond, on the riparian fringe and the surrounding area. An interpretive trail was developed around the pond with signs created by a local master watercolor artist. Local schools built and installed picnic tables, benches and a kiosk. Cleveland-Cliffs created pond lesson plans tied to the Michigan Curriculum Framework, developed inexpensive teaching kits and hosted a workshop for teachers from nine local schools. Classes regularly utilize the pond during the school year conducting environmental studies. Nesting boxes, wildflower gardens, bat houses, frog deformity surveys and water quality studies are a few of the activities that classes have conducted at the pond.

Jan 1, 2007

By D Lichti

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By Jill Murray

This study focuses on the amosite mining region in South Africa and associated health effects, compared to other mined asbestos fiber types. Historically, dust and fiber levels were high in the amosite mills and mines, and many miners and members of the surrounding communities were exposed to the fibers. Research has shown that amosite produces both benign and malignant disease. Nevertheless, the mesotheliomagenic potential of amosite is several fold lower than crocidolite. The risk of disease associated with amosite exposure is difficult to quantify. Reasons for this include the scarcity of available information, including fiber measurements, and case ascertainment, as well as the juxtaposition of the amosite and crocidolite asbestos seams in South Africa. © 2007 Elsevier Inc. All rights reserved. Keywords: Amosite; Mesothelioma; Crocidolite; South Africa; Asbestos

Jan 1, 2007