Search Documents

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007

By S. Saeb, C. Francke

Introduction Although mining in one form or another has existed for millennia, the use of numerical methods for mine design is a relatively recent development. The basic physics that control the behavior of rock or soil have been known for centuries, but it wasn’t until the last half of the twentieth century that analytical methods that could accurately predict the behavior of a large, irregular rock mass were developed. Before the advent of modern computers combined with differential and integral analytical methods, numerical methods available to mining engineers were limited to closed form solutions for simple excavation geometries. Today, mine-scale three-dimensional stress analyses can be performed on a relatively inexpensive personal computer. Many of the recent advances in rock mechanics modeling are the result of research funded as part of nuclear waste repositories around the world. The large scale exacting performance requirements of waste repositories are frequently very different from traditional rock mechanics projects. These facilities are designed and built under tighter control and scrutiny because of the potential hazards they present to the public. Therefore, a great deal of research towards advancing rock mechanics and numerical modeling resulted from these projects. Much of the repository research is applicable to commercial mines. The advances in modeling programs have been paralleled by advances in computer equipment. Today, a moderately equipped personal computer can handle most mine geomechanical modeling projects in a reasonable period of time. While the learning curve varies, an engineer with modeling experience can develop a medium sized model in a few days. The relatively low investment cost of geomechanical modeling today makes it accessible to most mining operations. The benefits of a solid geomechanical modeling program include reduced operating costs, improved safety, and reduced design costs.

Jan 1, 2007

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By Richard Peaker, Jens Lichter, Alexander V. Potapov

"The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism.This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.INTRODUCTIONThe great majority of newly installed cells in mineral processing plants world-wide are of the cylindrical tank design and this tank shape offers a number of hydraulic advantages over the older style of square cells. Cylindrical cells give symmetrical flow patterns and by careful design of the mechanism and tank internals, the flow patterns generated can concentrate the more intense mixing in the lower portion of the cell to promote good solids suspension and particlebubble contact. Simultaneously, cylindrical tank design gives a more quiescent upper zone for particle-bubble transport into the froth zone. These symmetrical flow patterns are naturally disturbed in normal operation by the slurry inflow and outflow from the individual cells. The challenge for flotation cell designers is to determine the magnitude of these flow disturbances, and to assess whether or when the inflow and outflow rates have a sufficient impact on the hydraulic flow patterns so as to potentially affect the metallurgical performance of the flotation cell."

Jan 1, 2007

By C. A. Rawlins

Deep underground mines use refrigeration systems to provide a reasonably comfortable ambient environment to increase productivity and to maintain safety as a priority. Deep level gold mines maintain the environment at an acceptable temperature, i.e. 27°C. However, the increasing cost of doing so through refrigeration is becoming a significant factor in the economic viability of mines. This paper discusses of the important facet of energy losses in cooling reticulation systems, laying with the specific emphasis on the subject of chilled water transport pipe insulation and its thermo-dynamic relationships. Aspects relating to the deterioration of open cell-type insulation materials such as polyurethane/styrene foams and the use of Phenolic resins that have good fire retardation properties have been investigated. The thermal conductivities of these insulation media are good (meaning below 0.05 W/°C)However, they are known to be negatively influenced by water vapour ingress and vapour pressure differences that result in the ingress of water into the material by means of absorption, condensation, hygrospicity, permeability and capillary action, to name a few of many. The overall effect on mine cooling efficiency takes in the two forms: first by the loss of refrigeration or increased chill in the water temperature arriving in a given section and second, by a loss in transfer efficiency when the gap between the arriving water temperature and the actual air temperature decreases. Keywords: Conductivity, vapour, insulation, fluid, thermal, temperature, pressure, transport, refrigeration.

Jan 1, 2007

By Francis Kendorski

The mining engineering design professional has limited practical and reliable tools for planning successful room-and-pillar stone mines using readily-available and collectible information. Three techniques are in common use today: the hard rock CANMET method of Hedley and Grant, the hard rock method of Stacey and Page, and the oil shale method of Hardy and Agapito. Other methods have been proposed, such as the USBM method of Obert and Duvall, the CSIR/Penn State method of Bieniawski, and the soft rock confined core method of Abel, Wilson, and Ashwin. However, the latter have practical shortcomings when applied to room-and-pillar stone mines such as developed for construction aggregate production. Ideally, the use of multiple techniques resulting in the same acceptable and reliable answer is the goal. Recently, in several underground stone mines areas of undersized pillars were examined. These undersized pillars apparently resulted from non-adherence to a mine plan. These undersized pillars now exhibit strong evidence of incipient failure such as slabbing, opening of through-going fractures, and hour-glassing. This situation allows examination of pillar designs at a ?safety factor? of essentially one. This rare opportunity allowed the examination of the suitability and adjustment of the first three design methods discussed, resulting in greater overall confidence in the methodologies.

Jan 1, 2007

By G. S. Ospanova

The results of complex processing sulphide copper ore and advantages of recovery of copper by vat and heap leaching, sorption, cementation and electrolytic solutions processing and utilization of waste material after heap leaching of copper for production of building materials were investigated. The combined chemical solvents with the additives of oxidizing agents are developed at the KazNTU. The solvents are inorganic or organic chemical reagents, which form complexes of Cu, Au, Ag, Pt, Ni, Sr, Co etc. Recovery of non-ferrous metals from solutions and purification of industrial waste waters is carried out on the base of using new synthetic and natural sorbents (from local raw materials) which are able to bind ions in both cationic and anionic forms depending on type of ligands and external conditions. Optimum parameters of copper sorption were determined. The developed wasteless technologies of copper extraction from sulphide ores with usage of new non-toxic solvents and accessible sorbents with full recycling of water are tested in pilot scale heap leaching, and are recommended as the ecological, economical and practical alternative to traditional methods.

Jan 1, 2007

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By I. B. Schalamuk, R. E. de Barrio, M. J. Pons, M. B. Franchini, L. Meinert

"Several Fe, Fe-Cu, and Cu-Ag prospects hosted by Mesozoic carbonate-rich sedimentary rocks that were intruded by diorite stocks define an approximately 20 × 200 km belt along the Andes Cordillera of southwest Mendoza province, Argentina (34°-36°S). This belt includes the Hierro Indio and Vegas Peladas Fe skarns, Las Choicas, and several other Cu-(Ag) prospects.The main features of the Fe skarns include: association with mantle-derived middle Miocene (~15-11 Ma) diorite stocks and sills; widespread alteration including epidote ± amphibole ± magnetite endoskarns, and zoned garnet (Grs0-66 Adr32.5-100) ± magnetite ± pyroxene (Di24-50 Jo2-9 Hd74-41) exoskarns formed from oxidized, saline, high-temperature brines (530º-660ºC; 60-70 wt.% NaCl equiv.); and magnetite-hematite orebodies associated with quartz ± epidote ± calcite ± actinolite formed at lower temperatures (290º-436ºC) from saline fluids (32-50 wt.% NaCl equiv.) of magmatic origin.West of the Fe skarn belt, the Valle Hermoso district covers more than 300 km2 and hosts several poorly known Cu-(Ag) prospects (estimated 30 Mt with 1.5% Cu and 20 g/t Ag). These prospects share many characteristics with the iron oxide copper-gold-type systems and manto-type Cu deposits of northern and central Chile. One of the prospects (Las Choicas) is located at the apex of a regional 015°-trending anticline, along the contact of stratified calcareous sandstone and limestone (Neocallovian-Oxfordian) with a diorite pluton. This pluton has positive Ta and Nb anomalies (on normalized diagrams) and a high Ti content, features uncommon in Miocene diorites associated with Fe skarns and of magmas derived from sub-arc mantle sources. Alteration at Las Choicas includes early widespread chlorite + calcite ± albite ± scapolite ± ilmenite or titanite ± apatite, and local actinolite ± hematite ± biotite alteration of diorite and sedimentary rocks along contacts. Later Cu mineralization (1%-10% Cu) is associated with calcite ± albite ± quartz alteration in fractures, vein networks, and crackle breccias. Mineralization is zoned from bornite ± chalcopyrite ± millerite with Zn, As, Mo, Ag, and U anomalies in the main orebody, through chalcopyrite-rich breccias with Zn anomalies, and chalcopyrite ± tetrahedrite vein networks with Sb, As, Ag, and Zn anomalies in the uppermost zone, to a Cu-depleted pyrite-rich envelope with Co anomalies, and finally to late, barren calcite veins in distal zones."

Jan 1, 2007

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By S. Garcia, J. Gebhardt, D. McBride, A. Hernandez, A. Esplín, M. Cross

The Minera Yanacocha operation consists of several heaps interconnected with ponds and gold recovery plants and presents various operating challenges. A comprehensive process model has been developed in order to better understand the effects of certain operating parameters and inventory issues. An integral component of the process water/mass balance is a model of each heap that describes heap behavior based on the individual characteristics of the heap. The heap models are linked to a mass balancing program in order to track flows and concentrations throughout the circuit. A case study of the process heap model is presented for the La Quinua heap, including results for the normal base line operation and several operational problems such as loss of solution flow to the heap (i.e., pump failure), increased flow to a section of the heap (i.e., pond volume control), effect of significant rain events, and impact of a change in material properties (i.e., change in ore type). The impact on heap operating efficiency is discussed with regard to effects on recovery and gold solution grades.

Jan 1, 2007

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than &apos;LME Gr&apos;. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By M. Eyll-Vetter

The operation of large opencast mines in a densely populated area in the centre of Europe involves an inevitable interference in the region. Thus, this is only possible with general acceptance by the regional stakeholders. In order to achieve this general acceptance, it is necessary to develop sound common concepts and to engage in a continuous dialogue with the stakeholders. The aim is to create seminal structures of relevance to the regional economy, taking into account the interests of the various stakeholders like e.g. authorities, local governments, the regional public, and churches. The recultivation of the mined-out areas represents the offset for the mining activities. RWE Power has reached high acceptance of its recultivation. This high acceptance is illustrated by various examples, from biotopes to high-yield agriculture and recreational areas. Thus, recultivation covers all the elements of sustainable development from social compatibility to ecological as well as economic aspects. This is only achievable through an intensive stakeholder dialogue in the region: The communities concerned are intensively involved in the planning and approval process for the new landscape. As far as social compatibility - one of the aspects of sustainable development - is concerned, the necessary resettlement of whole villages is one of the principal challenges. Over the last few decades, RWE Power has developed an approach that is broadly recognised by the stake-holders in the region. The best proof for this is the high proportion of resettlees taking part in the joint resettlement scheme offered. This can only be achieved by constant involvement of the stakeholders in the resettlement process. In conclusion, it can be stated that RWE Power has implemented a well-functioning stakeholder dialogue that guarantees the general acceptance necessary for mining operations.

Jan 1, 2007

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By D. Eastick, S. Hardcastle

"Over the last few years, a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell-powered equipment into underground mines to replaced diesel engine-powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine’s energy consumption, its associated greenhouse gas impact, and also reduce a mine’s significant ventilation-associated costs. Fuel cell-powered equipment also has the advantage of lower noise and heat production compared to its equivalent diesel-powered counterpart.The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions, and minimum velocity requirements.However, another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations, these factors change, and dispersion and buoyancy are limited; time may not be available and, in non-coal mines, ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical. Consequently, ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings, and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation, such as a hydrogen leak from the fuel cell stack or its distribution system."

Jan 1, 2007