Search Documents

By Sophia Wong

Nickel is used in a wide variety of applications from consumer goods to industrial uses. In many of these uses, nickel contributes to the environmental attributes of the product. The challenge, however, is measuring that contribution, comparing it to the environmental cost of production, and communicating the role of nickel to the customer in a way that is easy to understand. This paper presents the Nickel Institute?s approach to climate change as a global commodity industry association, and discusses where we stand with regard to some of these key questions. It also identifies issues for the nickel industry moving forward ? challenges that are likely to be common to other commodities.

May 1, 2009

By C. Lambert

It has been shown that contacts between host rock and engineered barriers may be critical in the design of deep radioactive waste repositories. Water is expected to reach the interface zone after the re-saturation of the geological massive and its presence may lead to concrete leaching. Such a phenomenon could increase the interface transmissivity and compromise the confinement of radioactive waste. Recent experimental results from Buzzi et al. (2008) have enhanced how concrete leaching can drastically change the mechanical behaviour of such interfaces. Because of the local loss of strength resulting from leaching, shearing resulted in a degradation of the interface asperities. Similarly to rock joints, intact interfaces exhibit a usual contracting-dilating behaviour. On the contrary, depending on the extent of leaching, the degraded interface can display a fully contracting. This paper intends to investigate the influence of concrete leaching on the mechanical behaviour of host rock-concrete interfaces. The leaching process consists in the dissolution of some of the hydrates of the cement paste, leading to a reduction of the strength and Young's modulus. A discrete model has been developed with PFC3D where a simplified interface morphology has been introduced using a saw-tooth description of the asperities.

May 1, 2009

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By Willie van Niekerk

As mining projects get larger and more complex there is a need to examine the use of project management techniques developed for large construction projects in order to ensure completion of the project on time and budget. In recent years the construction/civil industry has sought new methods to ensure that multimillion dollar projects involving multiple contractors, working in an increasingly legislated work environment, are delivered to the clients satisfaction. The paper describes these methods, which range from program management to systems and tools to gather all project information such as schedule and cost, and relates how these can be applied to large international mining projects. The paper also describes the benefits that an independent project manager can bring to a client or owner?s team by setting up the relevant organization and controls together with the appropriate contract and procurement strategy.

May 1, 2009

By J. A. Vallejos

Re-entry protocols are a tactical approach for controlling risk after blasts or large events in seismically active mines. Based on the results of a survey on 18 seismically active mines, mostly in Ontario, current re-entry practices are summarized. Over half of the mines in Ontario use event decay rate analysis as their primary re-entry decision making parameter. We study in detail the applicability of the Omori?s law as an equation for describing the event decay rate for more than 250 mining-induced aftershock sequences in seven different environments. Practical guidelines for the use of the Omori equation as a re-entry criterion are proposed.

May 1, 2009

By Yun-Jie Wei

Seismic areas were in the eastern margin of the Qinghai-Tibet plain, whose structures were complicated, mainly composed of Maowen fault, Yingxiu fault and Pengxian-guanxian fault. The rapid rise of the Qinghai-Tibet plain led the crustal material of the eastern edge to move to the southeast along the faults on a large scale since the late Cenozoic; Minshan block structure and Long Men Mountain tectonic zone represented the strong nappe thrust movement as the east boundary of Chuanqing slip block; the stress was accumulating when squeezed, which to a certain extent resulted in breakdown of the crust, and earthquakes. The shock speed, high-energy accumulation, and the reversed dextrorotation of the earthquake fault characteristics et al. happened, which caused the development of secondary geological disastersts. According to on-site investigation, the typical geological disasters had thrust rock collapse, the instability deposit, the revival of potential debris flow et al. whose genetic model had been analysed.

May 1, 2009

By Anna M. Ferrero

Stability condition of underground excavations have to be assessed to guarantee safe operations within the quarrying working areas. This objective requires a reliable assessment of the rock mass natural state of stress and of the stress redistribution induced by the excavations. This goal is often complicated by difficult geological conditions induced by tectonic stresses, complex topographies and large and irregular excavation geometries. Consequently, the acting state of stress needs to be measured by specific in situ measurement devices. This work refers on an in situ measurements campaign carried out by CSIRO tests in an underground quarry located in the Carrara marble basin. The difficult path carried out for interpretation of the measurements is described in this paper. In particular, the numerical modeling performed using the Boundary Element Method (BEM) first, to study the influence of both surface topography and excavation geometry and then the Distinct Element Method (DEM) to evaluate the influence of rock discontinuities in the measurement zone are illustrated in this work. Parametrical analysis of the rock mass mechanical features is also described in order to calibrate the numerical models and analyze the experimental results. The work has been carried out trough several phases, which are: characterization of the rock mass through geostructural surveys: this allowed us to classify the rock mass and determine the mechanical and physical parameters necessary for modeling; on-site measurement of stress levels through the application of over coring techniques; numerical analyses for the simulation of excavation phases, using the Examine3D (BEM) engineering analysis code. comparison between the measured stress levels and those numerically calculated and subsequent calibration of the BEM model; Numerical model of the forecasted excavation based on the calibrated (BEM) model.

May 1, 2009

By Greg Gosson

These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own counsel in relation to any decision or course of action contemplated. Outline ??What is meant by a ?current technical report? under NI 43-101? ??When is a current technical report required? ??Who makes the decision regarding whether a technical report is current? ??Examples of the types of information that make a technical report no longer current for securities filing purposes.

May 1, 2009

There are many inherent risks in creating a mine plan for a new ore zone in an underground mine; one of such risks is the redistribution of stresses that could be a cause of instability. Using numerical modelling tools, it is possible to model the planned stope extraction sequence and evaluate the influence of mining induced stresses on the stability of remnant pillars, and use this information to remedy potential setbacks. This paper demonstrates this approach through a case study of the short-term mine plan of the Lapa mine of Agnico Eagle Mines Ltd., an underground gold mining operation near Val d?Or. Three-dimensional boundary element modelling is used to compute the stresses induced by the stope extraction sequence as planned with a longitudinal retreat mining method. The proposed methodology can be generalized to other mines that require an understanding of the stress concentrations at the pre-feasibility stage of mine design.

May 1, 2009

Burr Mineral Resource has: ?Grade / Thickness / Tonnage ?Dry Caprock ?Low Carnallite ?Low Clay / Insolubles ?Flat & Continuous Deposit ?Proper depth

May 1, 2009

By B. S. A. Tatone

The surface roughness of unfilled rock discontinuities has a major influence on the deformational and hydraulic behaviour of discontinuous rock masses. Although it is widely recognized that surface roughness is comprised of a large-scale (waviness) and small-scale (unevenness) components, most investigations of surface roughness have been restricted to small fracture surfaces (< 1m2). Hence, the influences of the large-scale components of roughness are often neglected. Furthermore, these investigations typically focus on analyzing roughness in terms of two-dimensional profiles rather than the complete three-dimensional geometry, which can lead to potentially biased estimates of roughness. This contribution demonstrates the use of a new optical digital measurement system, based on the principle of triangulation, to digitize a large-scale natural rock discontinuity surface at both outcrop-scale (~6m x 2m) and lab-scale (~100mm x 100mm). Subsequently, the digitized surfaces are systematically analyzed using the three-dimensional roughness methodology proposed by Grasselli to investigate the dependency of roughness on sample window size and measurement resolution.

May 1, 2009

By H. Soltanzadeh

This paper summarizes semi-analytical and closed-form solutions that can be used to assess the poroelastic stress changes induced within a porous formation (reservoir) during a pore pressure change. Further, solutions are presented for the stress discontinuities at the interfaces between reservoirs and the rocks that surround them. When used in combination with rock failure criteria, these solutions enable relatively simple analyses of the potential for induced fracturing or fault reactivation within a reservoir or the rock immediately adjacent to it. The latter, in particular, is useful for assessing if the hydraulic integrity of the surrounding rock (i.e., the bounding seal) will be affected by a pore pressure change. The use of the approach presented in this paper is illustrated with an analysis of a pinnacle reef with dimensions and properties representative of reefs in the Zama oil field, northwestern Alberta, Canada. Scenarios of pore pressure decrease (during historical production operations) and pore pressure increase (during several years of acid gas injection operations) are analyzed, for three different idealizations of reservoir properties and geometry (two plane strain and one axisymmetric). These results suggest that that the potential for induced fracturing is not significant at any point within the reservoir or the surrounding rock for both the production and injection scenarios that were simulated. Similarly, fault reactivation was not predicted for the reservoir or any of the points that were analyzed in the surrounding rock. However, fault orientations having the greatest potential for reactivating during historical production operations were identified; thus, illustrating a means of using geomechanical models to focus geological characterization efforts on the features that are most critical to acid gas containment.

May 1, 2009

By C. C. Li

The D bolt is a new type of energy-absorbing rock support element recently developed in Nor-way. The D bolt is not only able to accommodate large rock deformations, but can also provide a load-bearing capacity as high as that of rebar bolts. Furthermore, the anchoring quality of the D bolt is similar to rebar bolts because of its multi-point anchoring design.

May 1, 2009

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By L. Li

The rock quality designation (RQD) was initially introduced by Deere (1963) for civil engineering. But, its application has been largely extended to rock mechanics and has become a fundamental parameter in geotechnical engineering (e.g., Hoek & Brown 1980; Milne et al. 1998). The success of this definition is due, in great part, to its simplicity. However, this index includes a number of limitations. Among these limitations, a critical one is associated with the arbitrarily selected threshold value (e.g., Priest & Hudson 1976). Consequently, the RQD value would vary with different threshold length for the same core. Also, using the customarily and universally adopted but very arbitrarily selected threshold value of 10 cm (for NX cores) in the assessment of RQD, the RQD values usually tend to be either high or low in most rock engineering. Some intermediate values (50%) are less frequently encountered (Harrison 1999). The original definition of RQD does not well represent the actual quality of rock masses. In this paper, an improved definition of rock quality designation (RQDc) is given.

May 1, 2009

CONSTRUCTED WETLANDS (CWs) ?Human-Constructed ?Built Specifically to Remove Contaminants ?Can Treat a Wide Variety of Wastewaters Including Stormwater(SW) ?Three Major Kinds ?Pond Wetlands ?Free Water Surface Wetlands (FWS) ?Sub-Surface Flow Wetlands (SSF) ?HSSF & VSSF

May 1, 2009

The rock mass classification systems were developed for different functions, including support selection, excavation method selection and the determination of rock mass engineering properties for excavation design, among others. This explains in part why we have several rock mass classification systems. It is often cautioned that the rock mass classifications are to be used for preliminary excavation support design, but this caution is now often overlooked and detail/final support design based on the rock mass classification systems. This paper advocates differentiating between rock mass classification for pre-excavation support planning and rock mass classification for at-face excavation performance assessment. It is concluded that most at-face excavation performance problems are attributable to confusing the virgin rock mass rating with the rock mass rating on exposure during excavation, and that this observation is independent of the method of excavation. Procedures are then presented for virgin rock mass rating and for at-face rock mass rating/assessment during excavation.

May 1, 2009

By Andreas Gaich

COMBINED 3D IMAGES _ Highly detailed 3D geometry _ Identification of fine fractures together with a general impression of the situation _ Dealing with unfavourable outcrop geometries

May 1, 2009