Search Documents

By G. T. Fisher

The U.S. Bureau of Mines conducted research on calcium ferrite slags to determine the distribution of Pb and minor elements (Ag, Cd, Zn, and Co) between Pb bullion and slag. These fundamental data are required to evaluate nonferrous smelting with calcium ferrite slags as a substitute for conventional iron silicate slags. Determinations were made in 25-cm3-capacity MgO crucibles at 1,250° C for 2 h in a CO-CO2 atmosphere with an O2 potential that would retard the formation of magnetite. Calcium ferrite slag composition variables studied were from 16 to 32 wt pct CaO in 2-pct increments and Si02 ranging from 1 to 5 wt pct in 1-pct increments with equal additions of MgO. For all compositions studied, the retention of Pb in the calcium ferrite slag was less than 1 wt pct, which compares favorably to about 6 wt pct Pb in conventional iron silicate slags used in smelting of Pb concentrates. Minor element distribution was insensitive to changes in slag composition in the range studied. However, slag composition had significant impact on the melting and fluidity of the slag.

Jan 1, 2010

By Charles D. Litton

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 2010

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By C. Iglesias

Innovation in the tilemaking ceramic industry is stressing properties like powder flowability, ability to toughen green tiles, so turning technological requirements of ball clays ever stricter in terms of plasticity, dispersion in water, rheological behavior, workability in the green state, refractoriness and firing colour. Technological performance of ball clays was improved by taking as benchmark the highest quality raw materials on the market. The mineralogy, plasticity, methylene blue index and ceramic response of the Patagonian ball clays are analogous to those of European clays, but improvement is needed to approach the highest quality materials. On this basis, the Frente A, Super, Puma, and Lote 8 deposits were selected and their characteristics enhanced by additions of highly plastic and white-firing corrective clays targeted on the benchmark. Porcelain stoneware formulations, containing improved ball clay mixes, were experimented at both laboratory and industrial scale. The improved ball clays behave like the best raw materials currently used, although modest changes occur in the mechanical properties, water absorption and whiteness of the fired products.

Jan 1, 2010

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By K. J. Maggs

The U.S. Bureau of Mines has investigated the chemical vapor deposition of diamond films on tungsten substrates. The effects of deposition parameters on the adhesion of the films was determined. The films were produced using a hot filament chemical vapor deposition system. Parameters investigated were substrate temperature and methane concentration in the feed gas. Film quality, morphology, and composition were characterized by scanning electron microscopy and Raman spectroscopy. Adhesion testing was performed using an indentation technique, and the results were quantified by relating adhesion to interface fracture toughness. Diamond films with well-faceted crystalline morphology with grain size greater than 1 µm had poor adhesion properties regardless of substrate temperature or methane concentration. Diamond films with smooth morphologies consisting of rounded clusters of small (<0.2 µm) diamond crystallites and amorphous carbon phases displayed much higher adhesion, although the conditions that led to the growth of these films are not understood.

Jan 1, 2010

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated&apos; the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental sampling error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centred on the sampling constant K and the exponent, alpha (a) of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis method and the heterogeneity test method purport to provide such constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine, and Lily mine. Two of these mines (Mponeng and Kloof) are typical Witwatersrand-type gold mines, and the third is an Archaean-type shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appear to be too small and do not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2010

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By D. Scott Scovira, Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance.

Jan 1, 2010

By Richard O. Kneisley

An empirical method, based on U. S. Bureau of Mines field studies in several Western U.S. coal mines, is presented for sizing gate road yield pillars. Discriminant analysis was used to generate functions separating successful from unsuccessful case studies. These functions relate the pillar width-height and extraction ratios and a pillar development factor to the Coal Mine Roof Rating System (CMRR), and are assumed to establish three criteria that other entry systems, under similar conditions, must satisfy. A program, Pillar Sizer, from user-provided inputs, generates a range of pillar sizes that meets the proposed criteria. Although the analysis is based on a sample consisting primarily of two-entry systems, the derived expressions generate pillar sizes closely agreeing with observed, two-entry and three-entry in situ pillars. It is concluded that the proposed approach should assist mine operators estimate entry system yield pillar dimensions.

Jan 1, 2010

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine&apos;s ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010