Search Documents

By X Zhang, B McFadzean, C T. O’Connor, S Pikinini

The Platreef in South Africa contains one of the world’s largest reserves of platinum group elements. One of the major platinum group minerals (PGM) components in this ore is sperrylite (PtAs₂), which has been found to be slow floating compared to the other PGMs. In a study aimed at determining the reasons for the poor floatability of sperrylite and to improve its recovery, tests were carried out to determine the interactions of the mineral with a range of standard and novel collectors. Microflotation tests were carried out to determine the hydrophobicity of the minerals before and after adsorption of collectors. In addition, experiments were carried out to determine the enthalpy and extent of collector adsorption on the minerals and to investigate electrochemical interactions between sperrylite and selected standard collectors. The results indicated that poor collector adsorption was the major cause for the poor floatability of sperrylite. Sperrylite had both poor natural (14.5 per cent) floatability and collector-induced flotation recoveries, the highest recovery of 26 per cent being observed using PNBX collector at pH 9. Moreover, the rest potential tests showed that the interaction of sperrylite with standard collectors such as xanthates was poor. The decrease in potential after the addition of the standard collectors ranged from 7.9 mV to 24.9 mV under alkaline conditions. Furthermore, sperrylite rest potentials remained unchanged with a change in pH from basic to acidic, indicating its resistance to surface alteration. Surface alteration of the minerals is key for the chemisorption of collectors to take place on the mineral surface. This was further emphasised by flotation recoveries at low pH, where only certain collectors responded positively to a decrease in pH and these were shown to have undergone a structural change. This work has highlighted the difficulties associated with sperrylite flotation and provides some direction for future research.

Aug 24, 2022

By K Aikawa, M Ito, K Mitsuhashi, Y Ebisu, J V. Satur, I Park, N Hiroyoshi, T Suto

Copper concentration using flotation is becoming more difficult, because of an increase in ore complexity accompanied by smaller grain sizes of copper minerals than usual, requiring finer grinding in order to liberate them. Project Arqueros, located at the mid northern part of Chile, is a copper mine project with an orebody consisting of various sulfides such as chalcopyrite, chalcocite, and bornite. Some of the copper minerals in Arqueros show low floatability mainly because of their fine grain size and resulted fine grinding size, and also because of the complex mineralogical composition. For example, chalcopyrite in Arqueros floats less than the other copper sulfide minerals. In this study we carried out some kinetic flotation tests with the Arqueros ore using a laboratory-scale forced air type flotation machine by varying the regrinding size. The products were assayed and mineralogically analysed to compare the minerals in their flotation behaviour with respect to size classes and liberation classes. The results were compared with a model calculation according to bubble size measurement. From the flotation testing and mineralogical analysis, it was found that copper minerals of the same size and liberation class floated at the same rate even with different regrinding size. At the same time the comparison between experiment and calculation showed that the fine particles of less than 5 µm size floated faster in actual than in the model applied. These results suggested that interactions among minerals of different species and of different sizes had positive impacts on the flotation rate of the fine particles. It indicates that this phenomenon can be applied to improve copper recovery in the project.

Aug 24, 2022

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By T M. Campos, J Silva, L M. Tavares, J Lichter, L P. Alves, B K. N Rocha, H D. G Turrer

The depletion of the richest ore deposits and the increase in number of mining projects involving deposits with complex mineralogy, higher competence and lower grade has led to an eminent need for improving understanding on multicomponent behaviour in mineral processing. One particularly relevant case is the ball milling of itabirite iron ores fed to the processing plant of Minas-Rio operation in Brazil. Dealing with the two main mineralogical components of the ore, namely hematite and quartz, the operation faces some challenges to improve understanding on how the two components behave in the process. Mathematical models have showed potential to give support in this task, but its applications to describe this type of industrial-scale grinding is still missing. The present work demonstrates the application of a multi-component ball mill model to simulate a closed ball mill circuit with hydrocyclones using the commercial software Integrated Extraction Simulator (IES). Model was calibrated on the basis of bench-scale tests and industrial surveys. Multi-component simulation results are then compared to those considering a single component in the feed, demonstrating the value and great insights that can be achieved by using the former in optimising plant operation.

Aug 24, 2022

By P Jonsén, S Larsson, M Parian, B I. Pålsson

The question of effective energy utilisation in grinding mills is not new. There are several conflicting arguments about tumbling mills, whether the efficiency is around 1 per cent or maybe 10 per cent, or even much lower. The energy not used is assumed to be lost as heating of the pulp, the grinding mill body, the charge, generation of shock waves and vibrations, etc. Stirred media mills on the other hand are generally considered to have better energy utilisation, but their energy efficiency is still not that clear. To shed some light on this a pilot-scale, wet stirred media mill was investigated over a range of operating conditions. The wet stirred media mill is a Drais PMH 5 TEX pearl mill fitted with an electric motor at 11 kW. It has been investigated over a range of operating conditions to try to balance the dissemination of the input energy in forms of the net grinding energy, mechanical energy losses, and the heating transferred to the pulp, the mill, the charge, and the cooling water. It is found that approximately 20–40 per cent of the input energy accounts for the grinding process. Also, that the difference between gross and net input electrical energy is mainly disseminated as heating of the pulp and cooling water. Mechanical energy losses appear to be much smaller than the heating effects. The use of a dispersant seems to mainly influence the heating effect.

Aug 24, 2022

By J J. Hanhiniemi, M S. Powell

A ‘Variable Blend and Rates’ model is developed for SAG mills which extends upon the JKSimMet® Variable Rates Model. Similarly, a ‘Variable Blend Residence Constrained Perfect Mixing’ Ball Mill model is also introduced, also extending upon the existing JKSimMet® model. These models are used in conjunction with JKSimMet® while employing external technical programs. The technical model is then used to inform an economic model described elsewhere in Hanhiniemi and Powell (2022), which calculate operating and unit costs based on operating conditions, design, and ore characterisation. The SAG and ball mill models include constraints beyond those in the JKSimMet® models. The SAG model constraints include Size Specific Energy (SSE) verification, charge weight limit, and assessment of the impact of media to ore composition in the charge using the SAG Charge SSE Model developed in this paper. The ball mill model includes residence time, volumetric capacity, and SSE verification constraints. These models are applied to Cortez Gold Mine in the processing of two very different ore types and their blends; ‘Horse Canyon’ which is softer in coarser sizes and competent is fine sizes, and ‘Wenban’ which is competent at coarser sizes but softer in fine sizes than Horse Canyon. Horse Canyon also has a finer run-of-mine size distribution then Wenban. The application of the model at this site included undertaking five surveys at varying blends. The behaviours of the blends and individual components is then studied in the SABC circuit. A nonlinearity is observed with throughputs increasing with blending. The newly developed modelling approach captures these responses. Controlled blending based on ore competence-by-size and size distribution was implemented by the site, which then realised significant improvements in throughput without any capital cost (Ntiamoah et al, 2020). The modelling developed in this paper is then compared to existing practice, and the new method was found to provide improved fidelity and utility. A three-dimensional surface is then developed using the model describing the SAG mill throughput capacity at varying conditions (speed-filling) versus varying blend. The change in throughput as a function of only the changing charge composition is presented. The result is nonlinear, and explanations are provided to describe this behaviour.

Aug 24, 2022

By H Park, L Wang

Froth flotation is one of the most widely used beneficiation processes for fine and ultrafine coals and minerals. Maintaining optimal metallurgical performance in industrial flotation operation is still a challenging task owing to the lack of an effective tool to diagnose the flotation performance in realtime. For this purpose, a number of flotation performance monitoring systems with different working principles have been developed to provide instant feedback for process control and optimisation. In this paper, for the first time, five different flotation performance monitoring systems were systematically compared through an on-site trial in a coking coal flotation plant in Queensland, Australia. The monitoring systems were used to measure (i) gas holdup, (ii) overflowing froth velocity, (iii) overflowing froth height, (iv) air recovery and (v) drag force exerted by overflowing froth, in an industrial flotation column and the outputs of these systems were collected simultaneously at a wide range of operating conditions. For each monitoring system, the best regression model describing the correlation between the system output and the flotation performance was selected from various regression models (eg linear, quadratic, power-law and logarithmic) using the Akaike information criterion (AIC). A comparison of the coefficient of determination (R2 ), residual sum of squares (RSS) and measuring accuracy at 95 per cent confidence level of the best regression models of these monitoring systems suggested that the drag sensor outperformed the other systems at a wide range of flotation operating conditions. The superior performance of the drag sensor was attributed to its distinctive design that enabled intimate sensing of variation of the overflowing froth properties. Furthermore, the drag sensor had the ability to monitor feed ash content variation when the other operation variables were set almost constant.

Aug 24, 2022

By G R. Ballantyne, A N. Mainza, M S. Powell, M Evertsson

Quantifying the performance of a comminution circuit relative to the potential that can be achieved is a standard requirement in justifying operating practice (the stick) and seeking operational upside (the carrot). Historic measures tend to focus on performance relative to laboratory design tests that provide a direct measure of specific grinding energy, such as the Bond Work index; or use dropweight breakage tests calibrated to a substantial database of operating sites, such as the SMC methodology. Although of value, such approaches are flawed in significant aspects. The assumption is that the laboratory prediction is correct and the single sample it is based on is representative. The database benchmarking methods are, by definition, locked into current average operating practice. These approaches do not illuminate upside; can ‘punish’ operations that are actually more efficient, such as grinding finer than standard operation; and reward poor operation that may comfortably produce a coarser grind than optimal for recovery or excess slimes that reduce recovery and increase water consumption and tailings volume. The authors present a set of established and easily applied measures, that draw together daily operation, highlight areas of opportunity and inefficiency, use simple samples and data, and can be used to provide the ‘size of the prize’ in pursuing specific areas of process improvement. These tools include size specific energy (SSE), overall operating effectiveness (OEE) which includes product quality, theory of constraints, and links this to the end objective – maximising the efficient production of valuable metals. Feeds into objective function driven by economics – financial return, energy, environment.

Aug 24, 2022

By L O. Filippov, A Piçarra, I V. Filippova, N P. Lima, K Silva

The reverse cationic flotation using the starch as depressor of iron oxides is the most efficient upgrading process when is applied to the simple systems composed by hematite/magnetite and quartz. The fundamental studies performed with iron ore samples from different deposits over the world (Brazil, Russia, Mexico) confirmed the inefficiency of starch when the silica content in the concentrate is controlled by Fe/Mg-bearing minerals. The main approaches for solving these issues focused on using new collector formulations or new depressants. However, the alternative depressants tested inhibited flotation of quartz or were less efficient as iron oxide depressant. In this work, a comparison between new amidoamine collector with conventionally used etheramine and oleate collectors in the flotation of pure minerals and actual iron ore samples was performed. The electrophoretic mobility, contact angle and infrared spectroscopy measurements allowed to deduce the hindrance effect as main mechanism of selective adsorption of the amidoamine on the quartz surface compared to hematite and kaolinite. Molecular modelling studies revealed that this steric hindrance effect can be explained by the combination of the "shield" formed by the coordinating water molecules on the (001)-D2 hematite surface and the large volume of the amidoamine head group. The amidoamine tested as collector without use of a depressant showed excellent flotation selectivity allowing the total flotation of quartz from a mixture with hematite. High collector performance and selectivity were confirmed during reverse flotation of quartz using continuous flotation column (D = 500 mm; H = 4000 mm) and allowed to produce the iron concentrates with more than 60 per cent of iron from the rejected slimes samples of Vargem Grande 2 processing plant (Iron Quadrangle, MG, Brazil). The new collector allowed to develop flexible flotation flow sheets to process the iron ore with a complex gangue mineralogy and unlock the old altered tailings and slimes product as new resources

Aug 24, 2022

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By S. K. Sharma, ANKUSH GALAV, G. S. P. Singh

Providing a suitable protective water barrier pillar (PWBP) is common to reduce inundation hazards in underground coal mines. The imperative factors influencing its performance include the water head acting on the pillar, cover depth, pillar width, strength properties, and permeability characteristics. The mechanical failure of such pillar is a stress-controlled phenomenon, whereas the hydraulic failure is a strain-based phenomenon. A finite-difference numerical modeling approach was developed to study the hydro-mechanical coupled behavior of protective water barrier pillars. The mechanical stability was evaluated in terms of the percentage of failed (ZoF) and intact zones. The influence of the strain-controlled weakening on the permeability of the flow medium was studied through the coupling of the mechanical and hydraulic effects. The coupled steady-state model was used to estimate the outflow rate and its hydraulic stability. The adequacy of the protective pillar was also investigated by assessing mechanical stability and capability to resist hydraulic pressure against the maximum expected water head. A seepage rate-based classification system has also been proposed to evaluate the seepage potential and assess the hydraulic stability. The model has been validated for two case studies at the cover depth of 136–189.5 m and the existing pillar width of 16–42 m against the water head of 25–141 m.

Aug 18, 2022

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By LUKAS FAHLE, Andrew J. Petruska, JURGEN F. BRUNE, Gabriel Walton, Elizabeth A. Holley

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (Lidar) data quality for rapid, digital, and eventually autonomous mine-wide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS provides data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest while reducing SLAM drift error by up to 90%. In collaboration with an operating block cave mine, we confirm these capabilities in field tests on a mine-wide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing, and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate, and comprehensive geotechnical inspections.

Aug 16, 2022

By A. Juganda, F. WILSON, H. PINHEIRO, N. SANDOVAL, J. F. Brune, G. E. Bogin Jr.

To evaluate methane explosion hazards in longwall coal mines, a CFD model was developed along with a 1/40th-scale, optically accessible model of an underground longwall coal mining section. In this project, CFD models assisted in the design of the physical model to ensure specifications were met for accurately representing the scaling physics as well as to assist in narrowing the experimental matrix and identifying key locations for sensor placement to measure velocity, pressure, and gas concentrations. This research will help develop strategies for methane monitoring that prevent methane ignitions and explosions in longwall coal operations.

Aug 15, 2022

By Y. FUJII, E. CHANDA, J. KODAMA, D. FUKUDA, M. NISHIHARA, Y. NAKAYAMA, P. SINKALA

For over 40 years, Mufulira underground copper mine has been recording incidents of rockburst. Laboratory tests and numerical analyses were carried out to understand the rockburst mechanism at the Mufulira mine. Rockburst did not occur in the chain pillars or at the mining face, but mainly in the mining drives along diminishing pillars or ahead of the mining face. RQD suggested that the rock mass in the rockburst areas was relatively intact. Laboratory tests confirmed that the rock at Mufulira mine is very strong and brittle. Elastic stress analyses for the rockburst sites by 3D displacement discontinuity method (DDM) indicated very high stress in the chain pillars and low-stress concentration at the sites of rockburst during the initial mining stages. However, there was no apparent positive correlation between the elastically calculated normal stress values and the occurrences of rockbursts. The 2D elastic FEM analysis was conducted under the concentrated stress by DDM and indicated that some stress increase with face advance for the rockburst in the vicinity of the mining face. However, stress severity indicated almost no increase, and the rockbursts cannot be explained as an instantaneous rock mass failure due to stress increase by mining. Therefore, a creep damage model was proposed to clarify the mechanism of the rockbursts. Cumulative rock damage was evaluated for the edge elements of each sidewall of the mining drives, based on the normal stresses by 3D DDM. The rockburst occurrences were well hindcasted. A method to estimate the volume of the rockburst source was proposed, and a likely result was obtained.

Aug 12, 2022

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By P. M. Mashaba, S. O. Bada

An advanced high internal phase water-in-oil (HIP W/O) emulsion binder and flotation with an internal dispersed water phase of 95 vol% was used to beneficiate South African weathered coal from discard dumps. Five coal samples with calorific values ranged from 8.48 MJ/kg to 20.94 MJ/kg were utilized. The performance of the HIP W/O emulsion was compared to that of kerosene in terms of the physicochemical properties of the clean coal products. A 5 kg/t emulsion binder addition produced a high-quality coal concentrate with 11.76% ash and a heating value of 28.61 MJ/kg from a sample containing 29.34% ash. Using the same dose and coal sample, kerosene resulted in a clean coal concentrate with 17.47% ash and a calorific value of 26.42 MJ/kg. Further samples were also beneficiated using 5 kg/t of W/O emulsion. The highest increase in calorific value was achieved from the beneficiation of a sample containing 48.71% ash, from 8.48 MJ/kg to 18.16 MJ/kg. It has been established that emulsion binders can upgrade coal samples dumped many decades ago.

Aug 2, 2022

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By F. Nakhaei, M. Le Roux, Q. P. Campbell, S. Botlhoko

The results of coal sink and float tests are plotted as washability curves. Analysis of these curves indicates the most effective method by which the coal can be cleaned. Sink and float experiments are samplingdependent, destructive, and use toxic chemicals. The present research introduces an alternative method based on a 3D imaging system called RhoVol, in which the density of individual particles is determined from mass and volume measurements. A quantitative error analysis was conducted on coal sample density measurements obtained by RhoVol, and the main factors influencing the errors identified and investigated. The results show that the drawback of this technique is related to its not being able to detect hidden concavities in the particle, resulting in an overestimation of particle volume. Furthermore, it is difficult to capture the impact of porosity and cracks on the volume of coal particles obtained from 3D silhouette images. This mismatch between the RhoVol data and sink and float test results has led to attempts to apply neural network (NN) and linear regression techniques to produce a fully reliable model for correction and estimation of coal density. The NN approach offers superior predictive capability over linear regression, and the estimated density distribution is in line with the sink and float analysis. The root mean square error in estimation of density using the NN model was less than 0.05 g/cm³.

Aug 2, 2022

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022