Search Documents

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By Heather N. Dougherty

In the absence of values for each influencing parameter and a known relationship of input-output space, novel approaches should be implemented as proxy solutions to mathematically complicated problems. Proxy solutions can be in the form of linear or non-linear multiple regression equations. Predicting the performance of gob gas ventholes is one of these mathematically complicated problems as it is difficult to know the exact relationships between various parameters influencing gob gas venthole (GGV) performance from active and sealed (completed) longwall panels. In this paper, a discussion of the NIOSH-developed software suite for methane control and prediction (MCP) based on an artificial neural network (ANN) is presented. The application of the ANN-based software suite to develop algebraic relationships for gob gas venthole performance prediction in sealed and active longwall panels is sought. Output information obtained from the NIOSH-MCP software as a response to various input parameters were used to create an input-output database for total flow and methane percentage from GGVs operating in active mines during completed and sealed panel situations. Due to the multi-variable nature of the software, outputs generated using the software for various inputs were used to develop analytical equations first using linear and then second using non-linear multivariable regression techniques. The advantage of this method is its ability to better understand the significant parameters of the relationships between the inputs and outputs for gob gas venthole production in active and sealed panels and to be able to predict their performances using relatively simple analytical functions.

Jan 1, 2010

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By Braden T. Lusk, Shannon P. Lusk, Kyle A. Perry

A high explosives shock tube has been constructed and developed to test blast resistant windows with pressure versus time waveforms similar to waveforms generated by arena testing. Calibration of the high explosives shock tube, or Large Arena Test Simulator (LATS), included numerous tests performed by detonating varying charge weights at different distances from three piezoelectric pressure sensors located at one end of the shock tube (where the test subject would be installed). The maximum reflected pressure and positive phase impulse were calculated for each waveform generated in the tests. Pressure versus distance and impulse versus distance graphs were generated. Results have been graphed in order to predict charge weights and distances that correlate to the desired pressure and impulse at the end of the tube for future tests. This is a valuable tool when testing expensive, job specific components so the loading requirements are met on the first attempt.

Jan 1, 2010

By N. Kuyucak

Uranium ores leached with sulphuric acid typically have poor dewatering properties. Applicability of controlled neutralization where gypsum precipitates as crystalline particles, improving dewatering properties of material was examined. Neutralized material was then dewatered using paste thickener to increase underflow density. The objectives are to maximize water recovery due to water scarcity and to produce suitable cemented paste fill material for optimizing underground ore recovery. Work was performed on acidic slurry samples collected after leaching but before the resin-in-pulp uranium recovery. Controlled neutralization greatly reduced volume of neutralization precipitates giving higher densities and improving the dewatering (filtration) properties. As a result it would be possible to increase the water recycled to the mill. Another benefit is that sulphate in the recycled water was reduced to saturation limit minimizing scaling of process equipment. Additional test work is needed; however, Unconfined Compressive Strength results imply that controlled neutralization increases the strength of paste fill and possibly offers opportunities towards a viable backfill option.

Jan 1, 2010

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By Ronald S. Conti

This U.S. Bureau of Mines report discusses the results of research conducted in the Bureau's experimental mine at Lake Lynn Laboratory on the response of fire sensors to simulated mine fires, which included (1) a slowly developing coal-conveyor belt fire, (2) a rapidly burning liquid fuel-belt fire, and (3) a liquid fuel-belt fire in the presence of diesel exhaust. During these tests, several mine fire sensors were evaluated with respect to sensor placement, spacing, and type. The data indicate that smoke sensors alarm several minutes before CO sensors do; and that, in the presence of diesel exhaust, a prototype diesel-discriminating smoke sensor can successfully function without being sensitive to the diesel contaminants. The vertical placement of sensors in the entry near the fire was also shown to be critical in terms of alarm times. Additional data showed that variations exist in response time and level of response for two brands of electrochemical CO sensor. Results also indicate that early detection of fires will improve the probability of miners' escape, because of reduced smoke concentrations during the incipient stages of the fire.

Jan 1, 2010

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By A. C. Smith

The U.S. Bureau of Mines evaluated the effectiveness of automatic water sprinkler systems on the suppression of incipient and propagating conveyor belt fires under ventilated conditions. Large-scale experiments were performed at airflows ranging from 1.1 to 4.6 m/s. In incipient fire experiments with 100°C, standard-response sprinklers installed above and between the belts, the sprinklers activated later, the peak heat release rates were larger, and more belting was consumed at the higher airflow. In similar experiments with 74 °C, fast-response sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of belting consumed was slightly higher at the lower airflow. In incipient fire experiments with sprinklers located only above the top belt, the heat release rate and amount of belting consumed was larger at the higher airflow. The propagating fire experiments showed that sprinklers located above and between the belts were effective in stopping flame propagation. Peak heat release rates and amount of belting consumed were larger at the higher airflows for both the 74 °C, fast-response and 100 °C, standard-response sprinklers. The sprinklers were equally effective at each airflow.

Jan 1, 2010

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

Refractory gold concentrates often contain sub-microscopic gold that is encapsulated within the crystal matrix of iron sulphide minerals such as pyrite, pyrrhotite and arsenopyrite. To recover the gold, the host mineral must generally be broken down chemically, by oxidative processes such as roasting, pressure oxidation or bacterial leaching, which expose the gold for subsequent recovery by leaching in cyanide solution. The focus of attention in these pre-treatment processes is usually the oxidation of the sulphides to elemental sulphur, sulphur dioxide gas or sulphate ions. Less attention is paid to the deportment of iron and the changes in its oxidation state, although this can have a profound effect on gold and silver liberation, as well as down stream operating costs. Iron sulphide minerals break down completely during pressure oxidation, and dissolve in the sulphuric acid solution that is generated from oxidation of the sulphides. This liberates the tiny gold particles that were originally trapped in the sulphide crystals, and gold recovery during subsequent cyanidation is usually very high (>95%). Iron goes into solution in the oxidation process, initially as ferrous sulphate, but this is rapidly oxidized to ferric sulphate, which then hydrolyzes and re-precipitates. The form of the precipitate varies depending on the operating conditions in the autoclave and the presence of certain metal cations. When the acidity in the autoclave is quite low (<20 g/L H2SO4) and the temperature is high (>200OC) the formation of hematite is favoured. When the acidity is high (>20 g/L H2SO4) and the temperature is relatively low (160 to 200OC), the formation of basic iron sulphate is favoured. If the ore or the leach solution contain significant levels of certain cations (such as Na+, K+, NH4+, Ag+ or Pb2+) and the acidity is high (>20 g/L H2SO4), jarosite compounds are favoured. Hematite is the desired iron product in the autoclave discharge, for both metallurgical and environmental reasons, but it is difficult to operate an autoclave under the conditions required for effective liberation of gold without converting some of the iron to basic iron sulphate and/or jarosite. These compounds fall into a category of iron compounds known generically as iron hydroxy sulphates, all of which can cause significant processing and environmental problems in the downstream gold process. This paper deals specifically with basic iron sulphate; the conditions under which it is formed in an autoclave, the problems that are caused by its presence in the feed to a cyanidation plant, and possible remedial strategies that can be adopted, both in the autoclave and downstream.

Jan 1, 2010

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950&apos;s, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Harry: Lobb Verakis

Mining operations have made tremendous strides in improving the safety of blasting as shown by the significant and continual decrease in fatalities and serious injuries. Advances in blasting technology and blasting practices have played a significant role in reducing fatalities and injuries. However, even with the decline of fatalities and injuries blast area security continues to be by far the leading factor in blasting accidents. Even though there continues to be an increase in the use of industrial explosives and blasting agents in the U.S.A., the decline in fatalities and injuries from blasting accidents has persisted.

Jan 1, 2010

By S. O. Bada

Coal is a complex mixture of organic and mineral constituents and is the most abundant resource of fossil energy in the world. In recent years, significant research into dry coal beneficiation has gained much attention, primarily due to the need to improve grades and reduce the environmental contaminants in coal without the use of water, and to achieve this in as cost-effective manner as possible, relative to wet beneficiation processes. This paper seeks to review the application of various electrostatic separators with their process principles, to draw comparisons between different dry beneficiation techniques with specific emphasis on the tribo-electrostatic separation method, and finally to report the results of tribo electrostatic separation conducted on various South African coals. Previous research conducted on Indian, European and American coals has indicated that this technique is likely to lead to significant economic benefit through the reduction of ash content, NOx and more specifically Sox by separating out the liberated Fe-S-bearing minerals prior to utilization. The removal of the latter suite of minerals is also likely to significantly reduce or eliminate the emissions of associated trace elements, including mercury and arsenic. The research results reported in this paper indicate that the rotary tribo-electrostatic process has the potential for significant upgrading of high ash pulverized South African coal. The impact of various operational parameters was investigated and key factors established for the optimum recovery of low ash and low sulphur fine coal.

Jan 1, 2010