Search Documents

By Ian J. Graham

Brothers volcano, in the southern Kermadec Arc, is host to two hydrothermal vent fields with very different geology, permeability, vent fluid compositions and mineralogy (see de Ronde et al. and Ditchburn et al. this volume). The NW caldera site contains mineral deposits (sulfide chimneys and crusts), which are either Cu-rich (?magmatic?) or, more commonly, Zn-rich (?epithermal?). The lower cone site, in contrast, is characterized by native sulfur mounds and spires. It has been proposed (see de Ronde et al. this volume) that the metals, especially Cu and possibly also Au, enter the hydrothermal system via injection and degassing of magma and/or the dissolution of metal-rich glasses. They are then transported rapidly upwards via magmatic volatiles along long (c. 2.5 km), narrow (c. 300 m diameter) pipes, consistent with evidence of vent fluids forming at higher than hydrostatic pressures, at relatively shallow depths. The NW caldera and cone sites may represent stages along a continuum between magmatic-hydrothermal and water/rock-dominated end-members. In this context, investigation of melt inclusions in conjunction with other geochemical and petrological research was carried out to ascertain the metal transporting conditions that may have led to mineral deposition and ore formation. Sixteen melt inclusions in plagioclase were analyzed for their chemical compositions from a typical cone dacite sample using LA-ICPMS at the University of Tasmania. The inclusions are typically glassy and commonly occur with other inclusions such as apatite, clinopyroxene, zircon, magnetite, sulfides and/or low-density fluids (Fig. 1). Major (XRF) and trace element (ICPMS) analyses were performed on whole rock samples collected during the 2005 Shinkai 6500 expedition. Haase et al., (2006) has also reported EPMA glass analyses from cone dacites, which may be used for comparison (Table 1). [ ]

Jan 1, 2010

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010

By Youliang He

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

The global tunneling industry has many challenges, both technically and financially, with the latter likely to be a significant feature over the next few years. Many industries have ad-opted standard practices in order to overcome specific technical challenges, from which standard out-comes are anticipated. In tunneling, however, every project is unique so standardized practice is not easy. This requires original thinking and being open to adopting new techniques and technologies as they emerge. Sprayed waterproofing is a hot industry topic and a paper recently presented at the North American Tunneling conference not only discussed this methodology for achieving a dry tunnel but also how it can reduce build costs and construction time. Despite their being relatively few ?universal truths? throughout the tunneling industry, there is one opinion that appears to be shared by most in the sector, ?all tunnels leak.?

Jan 1, 2010

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By John P. McDonnell

Cable supports offer several advantages over traditional secondary support methods by enhancing stress redistribution to pillars and gob areas, minimizing or eliminating timbers and cribs that reduce ventilation, eradicating material-handling injuries related to placement of crib supports, and providing a cost-effective alternative to secondary support. The U.S. Bureau of Mines, in researching alternatives to traditional roof support methods, designed and installed high-strength cable supports to improve the stability of longwall gate road and bleeder entries in a Western U.S. coal mine. With the cooperation of industry, methods were developed to install cable supports in a tailgate and bleeder entry test area using traditional resin cartridges. Resin-grouted cable bolts were also installed and evaluated in additional longwall gate road and bleeder entry systems at the study mine. The cable-bolted areas successfully maintained roof support throughout the tailgate and bleeder entries. Cable supports replaced wood cribbing as secondary support in the bleeder entry system and minimized the use of cribbing in the longwall tailgate entries. This report describes the theory, application, and advantages of cable supports and presents mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 2010

By Sathit Tandanand

Horizontal displacements and ground strains induced by mine subsidence are significant information needed for calculating damage and developing precautions against subsidence effects on surface structures. To devise a simple method for determining the surface horizonal displacements and strains simultaneously with the subsidence prediction, the U.S. Bureau of Mines examined the significance of the tilt number, which is the proportionality constant in the relationship between the horizontal displacement and the slope of the subsidence profile. The ratio of the tilt number to the critical radius of the subsidence trough is identical to the ratio of the maximum possible horizontal displacement to the full subsidence, which is found to be constant in most European coalfields. If this ratio is known for a particular minesite in the United States, then horizontal displacement and ground strains can be readily obtained from the primary subsidence data.

Jan 1, 2010

By Robert Hopler

Testing Stations Abroad At the Seventh International Congress of Applied Chemistry, Drs. Mente and Will communicated a paper on the above subject. All large coal-getting countries employ testing stations of some kind, in order to safeguard, to the highest possible extent, the lives of the men employed in this industry. Most countries employ galleries of considerable diameter, and fairly short length; but within recent times, long galleries, with drives and other accessories approaching as closely as possible the actual conditions of mining have been installed. The following are the details of the testing stations employed in the countries mentioned.

Jan 1, 2010

RÉSUMÉ Cet article traite d’une analyse technique et économique du concept du triage optique en vue d’améliorer la rentabilité des opérations minières. Le principe du tri optique et les principaux systèmes et modules servant au fonctionnement de l’appareil de triage sont décrits. un modèle a été développé pour analyser l’intérêt économique d’une opération de triage optique. L’étude est basée sur des données provenant d’une halde de minerai à faible teneur en or, déposé à la surface, et de minerai extrait des opérations souterraines courantes de la mine Beaufor au Québec. Les résultats de cette analyse indiquent que l’opération de triage optique permet d’améliorer grandement la performance économique; l’opération devient alors rentable pour des teneurs en or relativement petites.

Jan 1, 2010

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By Robert F. Chaiken

An absorption-desorption model of particle reactivity was employed to describe the observed relationship between two apparently diverse phenomena which have been the subject of considerable study at the U.S. Bureau of Mines: (1) coal-rock dust reflectance and (2) coal-rock dust explosibility. The model accounts for heterogeneities in particle-size and material properties; however, in the present report, only particle-size distribution is considered. A mean particle-size parameter, appropriate to the explosion extinction process, is derived, and then taken as appropriate to describing optical reflectance. The derived form-to-function relationships for the two processes, when compared with experimental data, suggest that a problem exists with previously derived theory relating optical reflectance to rock dust concentration. A reexamination of that theory leads to a new theoretical expression, changed by a factor of 2, for the variation of rock dust concentration with reflectance which is in quite good agreement with experimental results. The current work offers justification for measuring and establishing rock dust requirements for specific coal dust size distribution(s) found in the mine-distributions that undoubtedly depend on the mining method and the type of coalbed.

Jan 1, 2010

By S. D. Zhang

The first reinforced earth railway bridge abutment in China has been successfully constructed of September, 1985 under the supervision of the Reinforced Earth Researth Group of Shanghai Institute of Railway Technology. In order to verify the reliability of the designed structure and its behaviuors, the 1:10 reduced scale model tests in laboratory and field tests on the actual structure during construction were proceeded. Various loads of different positions were charged, the vertical and lateral earth pressure in the filling soil, the stresses developed in the reinforcements, and the deformations of the models or the actual structure were recorded in those tests. The behaviors recorded are presented and discussed in this paper.

Jan 1, 2010

By Y. X. Tong

The simplicity off Ø=0 analysis has been taken advantage of to evaluate the geotech­nical problems of open caissons, slurry trench walls and piles in Shanghai. Undrained shear strengths obtained by various testing methods are correlated with case record and experimental data. Some problems posed by the construction of tall buildings are briefly discussed. Comments on applications are made to help engineers deal with practical problems.

Jan 1, 2010

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By John C. Edwards

To increase the capability to predict the effectiveness of a flame arrester in the cooling of hot combustion gases expelled through a flame arrester, the U.S. Bureau of Mines developed an equilibrium. model and one-and three-dimensional transient thermal models of a flame arrester, which were used to predict the temperature evolution within the arrester and the maximum temperature at the external surface of the arrester. The models account for convective and conductive heat transport within the arrester and radiative losses at the exit surface. The gas flow through the arrester is established from an empirically derived relationship between the gas velocity and the pressure gradient across the arrester. Lateral heat loss from the arrester to the enclosure wall is accounted for in the three-dimensional model. The model calculations for maximum outside surface temperature of the arrester showed an approximate agreement with measured values for vent-area-to-enclosure-volume ratios between 12 and 28 in2?ft-3.

Jan 1, 2010

By J. Drimmer

The past several decades have seen the rapid expansion of multinational mining companies? exploration and production activities around the globe. This trend has resulted from a number of factors, including increased demand for resources as a result of worldwide economic growth, the diminishment of known and proven reserves, rising commodity prices, technology improvements, and the liberalization of investment regimes in developing countries with significant natural resources. With those opportunities, however, come associated risks and significantly increased legal compliance obligations that may be imposed by various bodies. That includes domestic regulations, as well as foreign civil and criminal laws with extraterritorial reach. A failure to adhere to those laws can have dire consequences, including substantial monetary fines and penalties, severe damage to a company?s reputation, and even jail time for individual company employees.

Jan 1, 2010

By A. de Meyer

Zincor experienced significant losses of metallic zinc to dross during the melting of zinc cathode plates. In this study five factors affecting the formation of dross are identified from literature. Dross from both the plant and that produced in the laboratory is characterized using XRD. An empirical model, based on laboratory-scale investigations, was developed to quantify the effect these factors on their own or in combination with each other has on the amount of zinc loss to dross. The predictive capability of the model is evaluated based on the laboratory-scale investigations. Predictions are made on the effects that heat treating the cathode plates prior to melting, increasing the cathode plate thickness, washing and drying prior to melting, and loading the furnace in a controlled manner have on the amount of zinc loss to dross. Keywords: Zinc, dross, optimize, smelter, yield, losses, empirical, model, XRD.

Jan 1, 2010

By A. Ochieng

Solids suspension influences the quality of mixing and energy requirement in a solid-liquid system, both of which determine the efficiency of industrial processes such as nickel precipitation. Nickel solids concentration distribution in a stirred tank was investigated using computational fluid dynamics (CFD) and experimental methods. The concentration distribution of the nickel solids was compared with that of sand and glass. The laser Doppler velocimetry (LDV) method was used to measure the velocity field for the liquid-only system and an optical technique was employed to determine the axial solids concentration distribution. Regions of in homogeneity in the tank were identified. It was found that, for a given solids loading, the solids concentration distribution depended on both particle size and particle size distribution. High solids loadings were investigated and a difference in the concentration distribution pattern was obtained with nickel, flint glass and sand particles. The CFD simulation results highlighted problems that could be associated with some conventional experimental methods of determining solids concentration distribution in a stirred tank. Keywords: nickel; CFD; simulation; mixing; solids suspension.

Jan 1, 2010