Search Documents

By Shiwei Wang, Ziwen Li, Chenhu Zhang, Peng Chen, Chengyong Wang

Accurate prediction of the partition coefficients in coal gravity separation is key to improving the preparation efficiency of coal and promoting its clean utilization. In China, the approximate formula method (AFM) has been applied to the calculation of coal gravity separation partition coefficients for decades, but its accuracy is limited. To improve the accuracy of the predicted partition coefficients, and thus the product yield of coal preparation plants, the present study proposes a modified hyperbolic tangent model to derive direct calculation formulas for the heavy medium and water medium separation partition coefficients. Four groups of coal samples were used to verify the accuracy of the direct formulas, and their predictions were compared with those of the AFM. The results showed that the partition coefficients and partition curves predicted by the direct formulas were closer to the actual values than those predicted by the AFM. Further, when the cleaned coal ash content was basically the same, the cleaned coal yield predicted by the direct formula was lower than that predicted by the AFM, and was also closer to the actual value. These results demonstrate that the direct formula produces more accurate results compared to the conventional AFM. As this formula has a reasonable theoretical basis, is simple to apply, and produces accurate results, it is expected to help improve the design and management level of coal preparation plants.

Oct 15, 2022

By Justin Srednicki, Chenming Zhou

Ambient electromagnetic (EM) noise (natural or manmade) is a major limiting factor for the design and operation of many electronic devices, including through-the-earth (TTE) communications and tracking systems. Extensive studies on EM noise were conducted by the US Bureau of Mines in the 1970s and 1980s. Changes in the design and operation of electrical equipment since then, however, have resulted in changes in the EM noise environment. This paper reviews past research on surveying EM noise in the extremely low-frequency (ELF) and very-low-frequency (VLF) bands, which are the operating bands for TTE systems, and introduces a new battery-powered, rugged, portable measurement system for surveying EM noise in mining environments. Examples of surveyed EM noise measurement results in and above an active underground coal mine, using the new system, are presented in terms of absolute magnetic field strength levels. A new metric, average noise level (ANL), is introduced to characterize the noise level relative to a particular frequency band for a specific location. It is found that EM noise in mining environments varies significantly with time and location. EM noise levels at frequencies of 30 Hz that shifted from power harmonics (e.g., 90, 150, 210, 270 Hz) are relatively low and their variation with time can be statistically modeled by a Gaussian distribution. The conclusions and findings presented in this paper can help better design and operate TTE communications and tracking systems in underground mines.

Oct 14, 2022

By H Wen

LongWangGou coalmine auxiliary inclined shaft heading face has a large section, fast heading speed, and large dust production. The problems of high concentration and wide distribution of dust in the roadway air are very prominent. To improve the efficiency of roadway ventilation and dustremoval, long-compression and short-suction (after this referred to as LCSS) are adopted. The dust concentration and airflow field distribution in the roadway are numerically simulated by FLUENT. The change of the position between the pressure duct and the exhaust duct and the different pressure-extraction ratios affect the distribution of airflow velocity, the formation of vortex zone, and the distribution of dust concentration in the roadway. When Ly = 25 m, Lc = 5.0 m, W = 1.2, a wind curtain is formed at 5 m in front of the heading face to prevent dust from spreading deeper into the roadway.

Oct 12, 2022

By Y Shougu

Many mine accidents will affect the mine ventilation system when they occur. At present, there is a lack of monitoring means to capture the occurrence of accidents in time by monitoring the ventilation system, so as to take emergency measures to reduce the loss of personnel and property. Pressure wave is an elastic wave existing in air. Most accidents in mine will cause obvious changes of pressure wave. It is an innovative idea to monitor the occurrence of accidents in mine by measuring pressure wave. The development and functions of the pressure monitoring device and related software are introduced in detail. The pressure wave monitoring test is carried out in San Xavier underground mining laboratory, and the D-wave and S-wave waveform data are collected. The waveform characteristics are analysed, and the main frequency distribution of the pressure wave is found to be within 1 Hz by using FFT. At the same time, the influence of the propagation distance of the pressure wave on the waveform is analysed. The propagation velocity of D-wave and S-wave are roughly calculated, and they are 279.6 m/s and 397.3 m/s respectively. S-wave is slightly faster than D-wave. Although there are errors and uncertainties in the test, the test verified the feasibility of the existence and collection of pressure waves in the ventilation roadway, and provides a method for the future study of the propagation of pressure waves in the mine ventilation system.

Oct 12, 2022

By F K. R Klose

Malmberget is a sublevel caving mine owned and operated by Luossavaara-Kiirunavaara Aktiebolag (LKAB), a Swedish state-owned iron ore mining company, in northern Sweden. The mine has an annual iron ore production of approximately 15 Mtpa. The current strategy foresees an expansion which will increase the mine’s depth considerably. Ventilation and air conditioning modelling for the planned expansion is ongoing. One of the most influential parameters for ventilation planning anddesign for a deep mine is geothermal gradient, which is crucial for the design of the refrigeration system. It is determined through virgin rock temperature (VRT) measurements carried out at various depth below the surface. This paper details these measurements and the determination of geothermal gradient for Malmberget Mine for the expansion study, which were necessitated by thelack of information for the focus depth and area.

Oct 12, 2022

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By A Hatt

This paper presents a case study of characterisation work undertaken at a greenfield exploration project to provide engineering and OH&S inputs for the design of a ventilation system. The paper discusses how comprehensive early characterisation of the ambient surface and underground environment including aspects related to heat, dusts, strata gas, and geologic/mineralogical factors enables incorporation of the right ventilation and non-ventilation controls at a study level to mitigate the risks identified.

Oct 12, 2022

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By F C. D Michelin

Blast fumes are a significant health risk to underground workers, containing several dangerous gases such as carbon monoxide (CO), nitrogen oxides (NOx) and ammonia. To ensure safe working conditions, workers are not normally allowed to re-enter a mine until the gases are cleared. To predict if gases can be cleared efficiently, simulations can be performed to estimate the gas levels following a blast. For accurate modelling, a calibrated airflow simulation is required in addition to blast-specific parameters such as the yield rate (representing the amount of gas released per kg of explosive) and the dispersion factor (representing how quickly the gases can enter the air stream from the explosive site). Those parameters are not easily determined, as they will vary from blast to blast. Many post-blast gas recordings on mine sites were studied and the correct parameters were determined to ensure an accurate gas simulation. The variability of the results was then analysed and correlation to known parameters is suggested. Finally, recommendations on how to determine the correct parameter are presented.

Oct 12, 2022

By B Beamish

The concept of a ‘critical velocity zone’ in the longwall goaf environment for the development of a spontaneous combustion event has been supported by numerical modelling. However, there is no experimental data available for Australian coals to show ventilation effects on the self-heating incubation behaviour of broken coal in the longwall goaf. A preliminary study using incubation testing has been completed on three high volatile bituminous coals (A, B and C) with R70 self-heating rate values of 3.86°C/h, 3.15°C/h and 2.09°C/h and moisture contents of 11.3 per cent, 3.9 per cent and 4.7 per cent, respectively. Mass to flow rates used in the adiabatic oven reaction vessel have been selected to be indicative of a sluggish, natural air leakage and medium ventilation environment. Under a sluggish ventilation flow rate all three coals incubate to thermal runaway in minimum time frames of 2.8–3.1 years, 34–42 days and 79–95 days, respectively. When the ventilation flow rate is increased to natural air leakage, coal A with the highest R70 value and highest moisture content selfheats to 28°C above mine ambient temperature before heat loss takes over due to moisture evaporation. However, both Coals B and C at this flow rate incubate to thermal runaway in a shorter time frame than under sluggish flow. At the medium ventilation flow rate, only Coal B incubates to thermal runaway, albeit after a significant extended period of time. These results show how important it is to determine the heat balance between the coal intrinsic reactivity (as indicated by the R70 value) and moisture content. The results also have implications for the possible location of the ‘critical velocity zone’ and subsequent hotspot development and migration.

Oct 12, 2022

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By T Roberts

The transition of mechanical cooling refrigerants from their inception in the 1800s through to the current day has been driven by several factors. Original refrigerants such as sulfur and carbon dioxide, chloromethane and ammonia, whilst effective came with toxicity and/or flammability issues. In 1930 DuPont trademarked a new synthetic refrigerant known as Freon® 12, this development was the introduction of ‘chlorofluorocarbons’ (CFCs).Throughout the 1930s and 1940s additional synthetic refrigerants were developed, namely Freon® 11 and Freon® 22. Due to their non-toxic and non-flammable characteristics, synthetic refrigerants were extensively used for domestic, commercial and industrial applications for the next 60 years.In 1985, one of the first scientific papers suggested a potential mechanism linking CFCs and areduction in the density of the ozone layer. In 1987 the Montreal protocol is ratified; it is the first UN treaty to be ratified by every country on earth. Due to CFC’s ozone depletion potential (ODP), the treaty required the consumption of CFC’s to be reduced by 50 per cent over the next ten years. By 1996 the phase out of CFC’s (Freon® 12) is completed, the phase out of HCFC (Freon® 22) refrigerants comes into effect.On 1 January 2018 the phase down of HFC’s begins. Whilst having zero impact on the ozone layer HFC refrigerants have high global warming potential (GWP). As we transition through the HFC phase down (2018–2035) we are beginning to see the emergence of what some consider to be the fourth synthetic wave, hydrofluoro-olefins (HFO’s). HFO’s and their blends have zero ODP and low GWP’s, ranging from 150 to less than 1. The reduction in GWP with HFO’s typically comes at the expense of flammability, which is not ideal. Each refrigerant has its optimal application, therefor when considering refrigerant choices for mining systems, a complete assessment of the environmental, health and safety, efficiency and commercial impacts should be considered now more than ever.

Oct 12, 2022

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By A Späth

Active explosion barriers are used to contain and suppress a methane gas and/or coal dust explosion propagation, including localised mine fires. Early research indicated that these active explosion barriers could be used on a mechanised cutting machine, making it the only technology that could suppress an explosion during its propagation phase at the cutting face. Thereby not only adding protection during mining operations but also reducing the development of toxic gases, fatal temperature increase and fatal overpressure build-up. During their evolution over the last two decades, further advantages of Active explosion barriers were proven in mine operations in countries such as South Africa and China. Characteristics such as effectivity, efficiency, mobility and space restrictions allow these systems to be used in various locations within a mine operation, including highwall operations. This improved technology contribution to safer coal mining was recognised by mine operators, workers and regulators. The Queensland’s Recognised Standard 21 (Resources Safety and Health Queensland (RSHQ), 2021) stipulated active explosion barriers as a technology to ensure the safety within their underground coalmines. The mobility and flexible implementation of the active explosion barriers allow a feasible and practical solution for all critical locations for explosion and fire management in an underground coalmine. The conformance to the Recognised Standard can be achieved all underground coal mining operations such as Bord and Pillar, and Longwall mining. This paper describes the conformance, implementation and use of Active explosion barriers for Longwall mining and development as well as Bord and Pillar mining in Queensland’s underground coalmines.

Oct 12, 2022

By O Salisbury

Ingress of air into the longwall goaf environment needs to be managed appropriately to reduce the risk of creating a spontaneous combustion event. The maingate goaf edge is an area of particular concern in this respect, as air often penetrates for some distance into the goaf along this region inbye of the longwall face. Since the flow rate in this part of the goaf is also quite low, an opportunity exists to disrupt the air pathway by implementing a barrier to the airflow. Previous attempts using plugs made from an assortment of materials have resulted in varying degrees of success. More recently, Narrabri Coal Operations (NCO) has introduced the use of a chemical foam that is mixed with nitrogen to produce a standing barrier with the consistency of shaving cream. The implementation of this practice has consistently proven to be very effective for reducing the oxygen concentration along the maingate goaf edge by systematically retreating the foaming unit with the longwall. This paper presents how the foam is applied in the underground goaf environment to prevent oxygen ingress and uses results from gas monitoring to confirm the foam effectiveness.

Oct 12, 2022

By M Francoeur

Oct 12, 2022

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022