Search Documents

By Xiao Ni

Alkyl hydroxamic acid was shown to be a suitable collector for the flotation of pyrochlore from carbonatite niobium oxide ores. In the direct batch rougher flotation from the ore without desliming, over 85% of the pyrochlore can be recovered at about 30% mass pull. Cleaner flotation tests showed that the rougher concentrate can be upgraded. The adsorption mechanisms of octyl hydroxamic acid (OHA) were studied by using high purity pyrochlore and calcite mineral samples and employing analytical measurements such as Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and UV/VIS spectroscopy. FTIR showed a shift of the vibrational frequencies of the carbonyl group in hydroxamic acid after adsorption on pyrochlore and calcite, and the shift was more pronounced on pyrochlore. XPS results indicated a lowering of the binding energies (chemical shift) of Nb3d5/2 and Ca2p3/2 electrons on pyrochlore, and the lowering of the binding energies of Ca2p3/2 electrons on calcite, again with the shift being more pronounced on pyrochlore. The results indicated hydroxamic acid formed stronger complexes with pyrochlore than with calcite. Adsorption isotherms indicated that OHA adsorbed more on pyrochlore than on calcite at low concentration. At high concentrations, the adsorption densities on both minerals were similar. All results explained the observed selectivity of the reagents in the flotation of the carbonatite niobium oxide ores.

Sep 1, 2012

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By Sanjeeva Latchireddi

The effective utilization of the energy in comminution devices depend on how efficiently the broken particles leave the breakage field as soon as they reach product size. In crushers the transport of broken particles smaller than CSS is done by gravity (vertical) thus allowing the energy to be applied to new particles. However, in AG/SAG mills, gravity becomes the energy field and the transport of particles is horizontal which needs a suitable discharge mechanism and has been found to have significant effect on grinding efficiency. The material transport in AG/SAG mills depend on how efficiently the discharge system (grate and pulp lifters) operates. Material transport plays a significant role on efficiency of horizontal grinding mills ? AG/SAG/Ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a Greenfield milling operation at Mirabela Mineração?s SantaRita Nickel operation located in northeastern part of Bahia in Brazil. This grinding circuit was commissioned in October 2009, which was designed as a typical SABC circuit to grind 4.6 mtpa (575tph) to produce a P80 of 125um with 10-12% ball charge in SAG mill. However, it has been operating as ABC circuit without any grinding media in SAG mill. The nameplate design capacity has been achieved in few days and has gradually increased to an average of +800 tph and still it is operating in ABC mode. The milling circuit commissioning resulted in small and relatively simple measures to rectify, which was reflected in the rapid commissioning of the milling circuit and it achieved the nameplate capacity within days. The Santa Rita grinding circuit consists of one 30?x 15.4? 8.5MW SAG Mill fitted with Outotec patented Turbo Pulp Lifters (TPL TM ) in close circuit with HP400 short head pebble crusher and one 20? x 28.4? 5.5MW Ball Mill in closed circuit with Warman cyclone cluster fitted with 10 x 26? CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimization, and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed. Keywords: Autogenous Grate (AG), Semi-Autogenous Grate (SAG, Turbo Pulp Lifter (TPL)

Sep 1, 2012

By B. Csoke

The Bond and the Hardgrove methods are widely used for the determination of the material?s grindability. Generally, the determination of the Bond work index of inhomogeneous materials can be carried out with high deviation using the conventional apparatuses and methods, because of the highly different grindability of components. This is more significant when the composite cement?s grindability is measured, which highly affects the design and operation of cement grinding mills. A possible solution can be the combined application of the Bond-method with the determination of the component?s weight ratio in the product and perform the Bond measurement until the steady state conditions of grindability coefficient (G) and chemical composition of the components are reached. To prove the applicability of the above mentioned idea systematic Bond and Hardgrove grindability tests were carried out of two phase composite materials. The experimental results showed that the application of the combined procedure is proven in order to have a more accurate and reliable calculation of the Bond work index of composite materials, especially when the components have significant difference in the grindability and concentration. The measurements also showed the possibilities and limits of the grindability test methods.

Sep 1, 2012

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By F. M. Isik

Due to not to being our own sources, some energy sources such as oil and natural gas which are used frequently, are not reliable energy sources for our country. Coal is an important energy source that Turkey also has a certain reserve as many countries have. To be able to use for many years the reserves of this source that comes from fossils, there is a great need to make more investigation and development activities on it. On behalf of using more productively the current sources, briquetting facility is represented that commenced production in The Aegean Lignite Establishment in 2005 which is in Manisa, Soma. This facility is a part of General Directorate of Turkish Coal. This facility is run by Soma Coal Establishment that works in return for royalty in a licensed field that belongs to TKI. As the demand of market for 0.5 mm dust coal diminishes, we had to accumulate and stock unmerchantable dust coal. Besides, we have intermixed 0.5- 1 mm powder coal and 0.1 ? 0.5 mm fine powder coal obtained as a result of washing in coal washer with thermic coal with low price as we could not find a client in the market. In this study, the production stages of briquette coal with high quality produced as a result of pressing by mixing 0.5- 1 mm powder coal and 0.1 ? 0.5 mm fine powder coal with molasse and lime, quality control, and data?s obtained about calories and solidity of products were presented. By briquetting of 0.5- 1 mm powder coal and 0.1 ? 0.5 mm fine powder coal washed in coal washer, it became possible to sell these coals on a high unit price and by providing the demand of coal of the market, we contributed to productivity of our firm. Keywords: briquette coal, briquetting, producing stage

Sep 1, 2012

By Kyoungkeun Yoo

A citric acid leaching test after heavy medium separation process was performed to remove the heavy metal contaminat such as Pb, Cu, and Zn from contaminated soil. The lead component was removed from soil by heavy medium separation whereas zinc component shows 0 % - 37.9 % removal ratio with particle size. The citric acid leaching was conducted to remove the remained zinc component. The removal ratio of Zn reached to more than 95 % under the conditions; 10 % in pulp density, 200 rpm in agitation speed, 50 °C, 2 mol/L in citric acid concentration at 2 hrs in leaching time. These results suggest that the heavy medium separation method followed by citric acid leaching is effective for treatment of soil contaminated with various chemical forms of heavy metal. Keywords: metal contaminated soil, citrate, heavy medium separation, zinc

Sep 1, 2012

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By A. V. Zimin

It is a well-known fact that usage of reverse cationic flotation in magnetite ores processing enables to improve the quality of magnetite concentrates. We designed an iron ore concentrate technology (with 70 -71 % of iron) including reverse cationic flotation in pneumo-mechanical flotators RIF (developed by RIVS Corporation, Russia) with good biodegradable etheramines as collectors for flotation of quartz. Practical application of high biodegradable flotation reagents decreases environmental impact risk of objects and enterprises of mining industrial complex. This work presents results of development of flotation technology for production of high quality ferruginous concentrates from magnetite ores of Russia and Ukraine deposits. Keywords: magnetite ores, reverse cationic flotation, ferruginous concentrates, pneumatic-mechanical flotation machines, environmental impact

Sep 1, 2012

By L. K. Smith

Flotation work conducted by CSIRO on both single minerals and high-arsenic copper ores from a number of sources, has shown it is possible to produce separate low-arsenic copper concentrates and high-arsenic copper concentrates from high-arsenic copper ores. The procedure involves controlled separations at high or low pulp potential regions exploiting subtle differences in the flotation behavior of the arsenic-bearing and non-arsenic-bearing copper minerals. An overview of several case studies investigating the applicability of the controlled potential flotation approach to the separation of copper and arsenic from sulfide copper ores is presented. It highlights the variables which influence the efficiency of the separation which include mineralogy, liberation and reagent selection. The procedure can produce a saleable low-arsenic copper concentrate, which can be directly smelted without penalty, and a high-arsenic low copper concentrate, which will require further processing. Keywords: flotation, copper, arsenic, controlled-potential flotation

Sep 1, 2012

By S. N. Sahu

Attempt was taken in this study to explore the misplacement phenomena in binary mixture in solid-liquid fluidisation system. The binary mixtures of hematite and quartz particles at different sizes were taken. The closed size range particles were taken to minimize the size and shape effect in fluidization. As both the minerals have appreciable density difference, the separation of both minerals with closed size range has an advantage. The experiments were conducted in different permutation and combination of different sizes of binary mixture to observe the fluidization phenomena. The samples were taken at different heights in fluidized zones and analyzed the distribution of particles of both minerals. The fluidization characteristics were evaluated with respect to operating and design parameters. It has been observed that when the terminal velocity of quartz and hematite particles is same or near to each other, then misplacement is significant. In general, the segregation index value is near to one, complete segregation takes place whereas this value is near to zero, complete mixing takes place. The experimental data were used to find out the segregation index for different size ratios of quartz and hematite particles and the values are within 0-1. When the size ratio is 1 or less, complete segregation takes place whereas this ratio is within 1.0-1.4, partial mixing takes place. Similarly, when the size ratio is within 1.4-2.0, complete mixing takes place whereas this ratio is within 2.0-4.6, then it moves towards complete segregation in inversion manner. Keywords: particulate fluidization, misplacement zone, bed expansion, terminal velocity, mixing characteristics, segregation index

Sep 1, 2012

By S. N. Shahcheraghi

Bioleaching method makes use of bacteria in solving metallic sulphides, so that these bacteria tend to convert insoluble metal sulphides into soluble sulphates. Since the kinetics description of this process is inevitable for better interpretation of relation between metabolism and growth of live organisms, as well as optimization of metals extraction processes, in this paper, this description is represented and designed in mathematic (kinetics) model for copper sulphide minerals based on Monod kinetics model. According to this model, special growth rate of bacteria (?) is a hyperbola function of restrictive substrate concentration (S). By Solving and developing of Monod kinetics model, a comprehensive kinetics model for bioleaching of copper sulphide minerals results. The designed is also applicable for other metal sulphides.

Sep 1, 2012

By M. N. Abdusalyamova

The Republic of Tajikistan has large mercury-antimony deposit. The Republic takes the second place in the countries of the CIS by having antimony recourses or the fourth place in the world. Recently, on the mine bottom horizons the resources of gold were found. Gold in the data ore is submitted as nanosize particles. Results of ores enrichment of bottom horizons of Djijikrut deposit are obtained by a method of flotation. The flow sheet includes the rougher flotation, two scavenging flotation and two cleaner flotation. As a result of enrichment of ore, the mercury-antimony concentrate with the contents of 51.5% of antimony and recovery 90.3% from ore with the content of mercury of 3.5% was received. The investigation of thallium, selenium, and tellurium distributions on products of enrichment was carried out. The most effective reagents are a mixture of oksafore and butyl xanthogenate. While applying this mixture of reagents it is possible to refuse of the use of activator - nitrate lead. The behavior of gold is in details investigated during enrichment. To collective flotation concentrate is extracted only 30% of gold. The basic quantity of gold concentrates in tailings of flotation and is not taken by existing traditional methods. The alternative innovative technology of gold extraction was created. Various methods of roasting of a collective mercury - antimony concentrate oxidizing and reducing are investigated. Vacuum distillation of concentrate allocation in serial sublimates mercury and antimony was designed. In the received calcine concentrates gold. At additional roasting of a calcine up to 900°? concentration of gold makes 30.6 g/t. The offered innovational technology in a complex allows to process ores and concentrates unique mercury-antimony?gold bearing raw material. Keywords: ore, concentrate, flotation, cyanidation, roasting, mercury, antimony, gold

Sep 1, 2012

By Auhin Kumar Maparu

Metal oxide nano-particles are used as additives in various industrial applications such as pigments in paints, additives in adhesives, plastics, cosmetics, functional coatings, personal care and health care products, for antibacterial applications and more recently in heat transfer applications. In most of these applications, usually dry nano-particle powders are added to the formulations. However, often it becomes difficult to achieve a uniform and stable dispersion of nano-particles in the given formulation. Thus, a scalable and commercially viable process for in-situ production of stable nano-particles suspensions in the desired medium will certainly be more beneficial. Ultra-fine grinding in high energy mills (planetary mill, stirred media mill) has been used to produce fine particles (sub-micron size). However, in order to obtain nano-particles (particle size <100 nm), the choice of appropriate dispersant and solvent is crucial, since freshly generated nano-particles tend to agglomerate due to their high surface reactivity. We have employed molecular modeling (MM) based selection methodology to arrive at the most suitable solvent?dispersant combination for preparation of the given metal oxide nano-particles. Molecular modeling techniques are employed to compute the interaction energy of a given dispersant with surface of the metal oxide particles in the presence of the dispersion medium. The interaction energy helps identify a dispersant that has strong affinity for the metal oxide surfaces allowing for strong dispersant adsorption and hence a more stable dispersion. For example, in case of aqueous nano-titania suspensions, poly-carboxylic acids like citric acid provide better dispersion than mono-carboxylic acids like lauric acid, mysristic acid, and oleic acid. While in non-aqueous medium like ethanol, p-hydroxybenzoic acid and glycerol trioleate perform better. The suspension is produced in-situ by ultra-fine grinding of the metal oxide powder in the presence of the selected dispersant and dispersion medium in a planetary ball mill. By careful selection of various process parameters such as percent loading of powder, jar filling, grinding media to powder ratio, time and amount of dispersant addition, both aqueous and non-aqueous suspensions of metal oxide nano-particles with average particle size less than 100 nm are produced. The aqueous suspensions of alumina and titania produced in presence of citric acid dispersant exhibit median particle size of 83 and 62 nm, respectively. These suspensions have been found to be stable for nearly 3 years. The nano-particles thus produced are used in the preparation of nano-fluids?advance heat transfer liquids, which show enhanced heat transfer capabilities and unaltered stability and performance even after several heating-cooling cycles. The nano-particles are also utilized for making efficient photo catalysts, which are found to be highly effective under sunlight. Keywords: stability, nano-fluid, milling, grinding, thermal conductivity, nanocoolant, photocatalyst

Sep 1, 2012

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By Peter M. Solozhenkin

Considering the main idea of the paper, namely that the interaction energy of reagents serves as a criterion used for their selection, as well as due to their insufficient study, the authors have therefore considered studying the aspects of computer modelling and molecular dynamics of largely used collectors for the flotation of nonferrous and precious metal ores. Three-dimensional molecular models for sulphydric reagents have been created, studying as well the distribution of the partial charges on their atoms. It has been shown that the value of the partial charge on the phosphorus atom in diethyldithiophosphinate and diethylmonothiophosphinate is high positive. The value of the partial charge of the sulphur atom is negative, strengthening its bond with the metal cations from the mineral surface. The molecular orbitals for the sulphydric reagents have been created determining as well the energy of their level. The computer modelling key parameters have therefore been defined. The new reagents have been tested for gold, copper and rhenium ore flotation. Gold recovery has increased with 4.2 - 4.7 %, copper recovery with 3.3 % and rhenium recovery with 15.5 %. A number of new flotation reagents have been recommended, such as: diethyldithiophosphate, (C2H5)2NCH2CH2OC(S)SNa, (C4H9NH)2P (S)SNa and also (C2H5)2P(S)ONa and (C2H5)2 P(O)S Na. Keywords: flotation, molecular modeling, design, orbital?s

Sep 1, 2012

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By T. N. Alexandrova

Results of mineralogical-technological research of carbonaceous rocks of Kimkansky precious metal occurrence are presented, on their basis new typemorphic natural and technological microelement associations were revealed using mathematical statistics methods. Keywords: carbonaceous rocks, processing, microelements, flotation, statistical criteria

Sep 1, 2012

Large quantities of electrical and electronic equipments are discarded at the end-of-life (EOL) in different industries and house hold applications. Their disposal is creating a challenging environmental problem due to the presence of hazardous metals and non-metallic materials such as epoxy resins and plastics including brominated flame retardants etc particularly in printed circuit boards (PCBs). The recovery valuable metals and separation of hazardous materials from discarded PCBs will not only conserve the resources but also mitigate the environmental pollution. From a recycling point of view for a sustainable society, the studies have been carried out for the recovery of metal values from EOL-PCBs of DVD video players (DVD-PCBs) and vacuum cleaners (VC-PCBs) using physical beneficiation techniques. The concentration of the metals was found to be 43 wt.% and 30 wt.% in DVD-PCBs and VC-PCBs, respectively. Both the PCBs samples were ground in a hammer mill after cutting and their size analysis was carried out. The liberation of the metallic and non-metallic fractions was investigated under the microscope for different size fractions. Subsequently, froth flotation and pneumatic air separation studied were carried out to enrich the metallic constituents. The studies showed the enrichment of metals in coarser particles (-1000 +150 µm) and non-metals in the finer particles -150 µm following mechanical recycling process. A grade of 90 % with 75% recovery was achieved by froth flotation, but lower grade and recovery of 75% and 65% respectively were obtained by pneumatic separation with -1500 µm powders for DVD-PCBs. A grade of 86% metal was obtained by froth flotation with 76% recovery in the case of VC-PCBs. The lower grade of 65% with almost same recovery was achieved during pneumatic separation studies due to lower concentration of metals in VC-PCBs. The studies also showed that the froth flotation is an efficient process for enrichment of metals from both the samples. The process is environmental friendly as no chemicals are employed during entire processing. The higher recovery and grade of metal is expected to be obtained on a large scale beneficiation process.

Sep 1, 2012

By Ricardo Montero

At this time, over 300 tons of Au are used in electronic equipment each year with other precious and strategic metals such as Ag, Pt, Pd, Cu, Nb, Ta, etc. After the use-phase, the electronic devices become electronic waste (e-waste); consequently it is important to consider e-waste as a secondary supply for recovery of these metals. One of the most important components is the printed circuit boards (PCBs) because the amount of their precious metals is ten times higher than rich precious metals bearing ore. This paper presents the recovery of Au, Ag, Cu and Nb from PCBs of discarded computers using leaching column technique. The amount of these metals in used PCBs was: 613 g/ton of Au, 1515 g/ton of Ag, 36 g/ton of Nb and 23.4 % of Cu. The PCBs were crushed with a hammer mill until reaching a particle size between 3.33 mm to 0.43 mm. Then, it was leached with sodium cyanide solution in a glass column using the following conditions: sodium cyanide concentration 4 g/L, flux 20 L/kg PCBs day, pH between 10.5 to 11 and leaching time 15 days. Every day, after leaching, the pregnant solutions passed through a column with activated carbon to complete the closed loop system. The following recoveries were obtained: 46.6% of Au, 51.3% of Ag, 47.2% of Nb and 62.3 % of Cu. The products obtained are: a) loaded carbon that contains the desired metals and b) processed PCBs with precious metal contents. A preliminary technical-economic study shows the feasibility to create a small-scale PCBs recycling plant. The initial investment is on the order of US$ 155 639, considering the recovered metals from loaded carbon. The internal rate of return for 10 years period (IRR) and net present value (NPV) estimated are 27% and US$ 105 926 respectively. Keywords: printed circuit boards, recovery, precious metals, niobium, leaching column

Sep 1, 2012