Search Documents

By Ali P. Gordon, James Williams

Joints gasketed with viscoelastic seals often receive an application of a secondary torque, i.e., retorque, in order to ensure joint tightness and proper sealing. The motivation of this study is to characterize and analytically model the load and deflection re-torque response of a single 25% glass-fiber reinforced polytetrafluorethylene (PTFE) gasket-bolted joint with serrated flange detail. The Burger-type viscoelastic modeling constants of the material are obtained through isolating the gasket from the bolt by performing a gasket creep test via a MTS electromechanical test frame. The re-load creep response is also investigated by re-loading the gasket after a period of initial creep to observe the response. The modeling constants obtained from the creep tests are used with a Burger-type viscoelastic model to predict the re-torque response of a single boltgasket test fixture in order to validate the ability of the model to simulate the re-torque response under various loading conditions and flange detail.

Jan 1, 2015

By Filipe de Menezes Torres, Augusto Pereira de Sa, Itavahn Alves da Silva, Eliana Ferreira Rodrigues, Carlos Antonio da Silva, Varadarajan Seshadri

Top slag eye opening which happens as a result of gas injection is a function of the gas flow rate in addition to other factors such as ladle geometry, porous plug location as well as slag properties. Slag eye opening leads to entrapment of atmospheric nitrogen, oxygen by the steel melt affecting adversely the steel quality. In this work aspects of mixing and eye formation in steel making ladles with inert gas injection have been analyzed through physical and mathematical modeling techniques. Influence of ladle, gas flow rate and distribution and slag properties has been assessed. A correlation for estimating eye opening has been developed. Results from PIV measurements and images of eye opening obtained using a camera have been utilized to validate results from CFD simulation.

Jan 1, 2015

By Sebastião Ribeiro, Leonardo Carneiro Sardinha, Alline Sardinha Cordeiro Morais, Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

Jan 1, 2015

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By Li Ma, Shaoguo Chen, Gele Qing, Qihang Liu, Keng Wu

Olivine contains higher MgO element, which can be added into blast furnace burden to improve slag stability and fluidity. Effect of calcined olivine and untreated olivine on low silicon pellet production process and quality was studied in this paper. The results shows, calcined olivine has no effect on bursting temperature of green pellet, however the bursting temperature of green pellet will decrease with increase of untreated olivine ratio. Untreated olivine has slight effect on green pellet strength than calcined olivine while the ratio is higher than 2%. The compressive strength of low silicon pellet will increase first and decrease afterwards with increases of calcined olivine ratio under firing temperature of 1250°C, whereas, the changing sequence is reverse fired under 1280°C. The result of untreated olivine pellet compressive strength is same as calcined olivine pellet. However, the compressive strength and metallurgical property of calcined olivine pellet is slightly higher than that of untreated olivine pellet under same condition.

Jan 1, 2015

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai

The purity of the electrolyte has an important influence on the content of the impurities in electrodeposited silicon. In this paper, effects of electrolysis temperature, current density and the time on the concentrations of two important impurities: phosphorus and iron in the electrolyte were investigated during the purification of Na3AlF6-10%K2SiF6-AlF3 melt. It was observed that the concentrations of P and Fe in the electrolyte decreased with the electrolysis temperature, current density and the electrolysis time increasing. X-ray fluorescence (XRF) of the electrolyte shows that the concentrations of P and Fe decrease from 4.2ppmw to 1.3ppmw and 204.0ppmw to 42.6ppmw, respectively. The removal rates of P and Fe are 69.08% and 79.12% when the electrolysis was performed for the duration of 3 hours and at a current density of 20mA·cm-2 while the operating temperature was 1225K.

Jan 1, 2015

By Jiang Feng, Li Chuanhua, Zhang Libo, Peng Jinhui, Ju Shaohua

Solvent extraction of Cu2+ from the leaching liquor contain Cu and Fe use a microfluidic technology. Currently, the conventional copper extraction process has many problems such as long distance and small driving force of mass transfer. In order to solve the problems, studies are carried out on the extraction process of low grade copper leaching liquid using Lix984N as an extractant with a new microfluidic solvent extraction technology. The effects of flow rate on the separation and extraction efficiency between Cu and Fe are studied, and the results show that a steady liquid-liquid interface of laminar flow is form in the micro-extractor, and extraction efficiency is 78 % and 2.5 % for Cu and Fe at the contact times of 0.84s respectively. Besides, the separation coefficient between Cu and Fe is as high as 140.04. The studied microfluidic technology has the advantages like improving extraction efficiency and reducing reaction time and providing the potential application in the hydrometallurgy extraction of Cu.

Jan 1, 2015

By Dietmar Eifler, Marcus Klein, Hendrik Kramer

Conventional methods to characterize the fatigue behavior of metallic materials are very time and cost consuming. That is why the new short-time procedure PHYBALCHT was developed at the Institute of Materials Science and Engineering at the University of Kaiserslautern. This innovative method requires only a planar material surface to perform cyclic force-controlled hardness indentation tests. To characterize the cyclic elastic-plastic behavior of the test material the change of the force-indentation-depth-hysteresis is plotted versus the number of indentation cycles. In accordance to the plastic strain amplitude the indentation-depth width of the hysteresis loop is measured at half minimum force and is called plastic indentation-depth amplitude. Its change as a function of the number of cycles of indentation can be described by power-laws. One of these power-laws contains the hardening-exponentCHT eII, which correlates very well with the amount of cyclic hardening in conventional constant amplitude fatigue tests. To identify heat-treatment-parameters and SAE 52100 TRIP-alloys with high hardening rates as well as their damage tolerance the PHYBALCHT- and PHYBALLIT-method were used. One modified SAE 52100 TRIP-alloy was investigated in detail. The fatigue behavior and the cyclic hardening of the selected SAE 52100 TRIP-alloy was investigated and compared with conventional SAE 52100. Conventional stress-controlled fatigue tests were performed on a servo-hydraulic test system with a frequency of 5 Hz and a load ratio of R = -1. Different rates of cyclic hardening were identified. The size of the nonmetallic inclusions leading to crack initiation and the number of cycles to failure were used to evaluate differences in the damage tolerance capability.

Jan 1, 2015

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By Jinjing Dua, Jun Zhua, Kuiren Liub, Bin Wang, Xiaolei Wua

V-Ti-Fe as hydrogen storage alloy was prepared by reducing metal oxides with a metallothermic reduction method. The deoxidation process of the V-Ti-Fe alloy was performed by electro-deoxidation and vacuum induction melting method, respectively. The results showed that the content of oxygen impurity can be controlled at about 0.2wt% after electrolyzing for 240min. Both the maximum values of hydrogen absorption capacity and the effective hydrogen desorption capacity are 2.65wt% and 1.01wt%, respectively. The deoxidization effect of vacuum induction melting process is more remarkable, with Ce as the reducing agent. It is found that Ce addition is beneficial for reducing the componential segregation, promoting the hydrogen absorption activation of V-Ti-Fe alloy. When m(Ce)/m(alloy) is up to 5%, the oxygen content has been reduced to 0.05wt% and the maximum hydrogen absorption capacity and the effective hydrogen desorption capacity are up to 3.36wt% and 1.85wt%, respectively.

Jan 1, 2015

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By D. I. Davidov, D. A. Shishkin, M. B. Rigmant, E. P. Romanov, N. N. Stepanova, N. V. Kazantseva

The Co-19 at.%Al-6 at.%W alloy was prepared by two methods of casting. We used arc melting under an argon atmosphere with casting into a copper water-cooled casting mold and induction melting furnace with casting into a ceramic Al2O3 mold. According to the X-ray and SEM analyses, phase compositions depend on the cooling rate of the ingot after melting. After arc melting, the cast alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co3W (DO19) type. After the induction melting, the alloy has a three-phase structure, consisting of  cobalt (FCC), intermetallic phases CoAl (B2) type, and Co7W6 () type. All phases in the investigated ternary alloy at the room temperature are ferromagnetic. Curie temperatures of all obtained phases were defined. It is shown that the magnetic properties of the studied alloy are typical for soft magnetic materials.

Jan 1, 2015

By José Brant, Douglas Torres, Rogério Navarro, Rodrigo Souza, Eduardo Brocchi

The steelmaking process requires the input of ferro-alloys to implement the adjustment of some elements composition in the final product. In the particular case of stainless steel production, the high carbon FeCr alloy stands out as one important precursor. However in the production of this material a certain quantity of fine powder with remarkable chromium and carbon content is also generated, which, in turn, could be processed through alkaline roasting in order to selectively recovery this element in a subsequent aqueous route. In the present work, this process is investigated, using excess of NaOH as oxidizing agent, and H2O2 for precipitating chromium as Cr(OH)3, which is next calcinated to Cr2O3. According to the results, the global achieved recovery has shown to be around 98%, suggesting that the proposed route can be seen as a potential process for chromium oxide production from the mentioned fine powder.

Jan 1, 2015

By Run-boWang, Fan-yi Meng, Jian-Liang Zhang, ZheWang

To elucidate the influence of high Al2O3 content on sinter softening and melting behavior, heating-up reduction test under load was carried out. In addition, microstructure study of sinter bed structure change at a different temperature was also made and the mechanism that the effect of Al2O3 content on sinter softening and melting property was discovered. SEM results showed that the increase of Al2O3 content favored the formation of Al2O3-rich slag phase, such as the eutectic (2CaO·SiO2-2CaO·Al2O3·SiO2-FeO) and gehlenite (2CaO·Al2O3·SiO2), resulting in the decrease of sinter Ts temperature. Further, high Al2O3 content improved the concentration of metallic iron and lowered the dripping temperature due to the decrease of slag liquidus temperature and viscosity. At a fixed basicity, it was indicated that there was a relationship between Al2O3 content and sinter softening-melting property. Based on the results, counter strategies to cope with the adverse effect of high Al2O3 content on the cohesive zone property were also proposed. It could provide guidance for the blast furnace operation of sinter with high Al2O3 content.

Jan 1, 2015

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015