Search Documents

By A. G. Nitschke, I. Ossenbühl, W. Dolsak, J. Dase

"The authors have successfully developed an innovative rehabilitation concept, which meets actual technical standards and minimizes the impact on the operation of a key conveyor tunnel. A flexible and stepwise ground support rehabilitation program utilized a combination of yielding steel arch sections with grout filled fabric hoses, which represents a fast and safe backfilling support system. The system was developed and successfully installed at Bingham Canyon Mine, the world’s largest open pit copper mine, which also includes numerous underground structures. The mine is owned and operated by Kennecott Utah Copper (RTKC) a fully owned subsidiary of Rio Tinto. The system was implemented at a conveyance tunnel, which was originally designed as a railroad tunnel, but was re-commissioned and is currently used as a conveyor belt tunnel to transport ore from the open pit to processing facilities outside the mine. The existing structure showed signs of overstressing due to movements in the surrounding rock mass, which had to be addressed with a yielding support system in order to provide safe access into the tunnel. However, the impact on the conveyor belt operation due to support installation was to be limited to the bare minimum. Keywords: rehabilitation, yielding support, mining, stabilization, and grout filled fabric hose.PROJECT DESCRIPTION The C6 Tunnel is considered a critical asset for the operation of the Bingham Canyon mine as it comprises the standard route for transporting crushed ore from the open pit to the processing facility on a continuous conveyor belt system. The C6 tunnel was originally built as a railroad tunnel. Construction was completed in 1959. The original horse-shoe shaped cross section of the tunnel was 18 feet wide and 24-1/2 feet high [8]. The tunnel length was approximately 18,000 feet. During its service life, the railroad tunnel has undergone several transformations. The length of the tunnel towards the Bingham Canyon pit was shortened over the course of mining operations and the railroad tracks in the tunnel were removed. The invert was partially backfilled (3 feet typical) and a 72 inches belt conveyor was installed. Currently, the C6 Tunnel is nominally only approximately 21 feet high and 15,000 feet long. Ground Support and Rehabilitation Measures prior to 2014 The C6 tunnel was mined mainly with conventional mining methods, using drill & blast as the typical one. However, the weak geological sections, such as those encountered in the Fortuna fault, were excavated by shaping and chipping with machine-held moils [8]."

Jan 1, 2015

By Gui Hua Wang, Xin Chang, Zhong Ying Han, Yuan Fang Cheng

"According to the geometrical characteristics of triangular meshes, Triangular Mesh Split Model (TMSM) based on a finite element method is proposed to simulate cracks propagation of fractured rock. With TMSM, stress intensity factors at the tip of cracks are obtained by far-field contour integral. Meanwhile, vector cross multiplication is adopted to fix the cracking unit, and maximum circumferential stress criterion is used to determine the crack propagation angle. Then crack dynamic propagation simulation is realized through local mesh split or node movement at crack tip. With this method, the crack can split apart a unit or extend along the mesh boundary, so the crack could extend along an arbitrary path and is not restricted by the initial mesh. The applicability of the mesh split algorithm is verified by the crack propagation examples of wing crack and multi-fractured rock mass with holes. The results show that this method not only has higher accuracy of fracture parameters calculation, but also can accurately simulate the crack initiation and propagation of rock under complex stress state such as tension, compression and shear. In addition, the far contour integral is introduced to determine the crack tip stress intensity factor and there is no need to reconstruct a singular element at the crack tip or to intensify the meshes. Compared with the existing mesh reconstruction algorithm, this method significantly improves the computational efficiency.INTRODUCTIONGenerally, rock is neither the full continuum, nor entirely discrete body, but rich in geological defects, such as joints and cracks. A large amount of geotechnical engineering practice shows that most fracture of rock is closely related to the internal joints, cracks and crack expansion (Horii et al., 1985; Wong et al., 1998). Although the classical theory of fracture mechanics established the theoretical foundation of crack initiation, propagation, so far it is still extremely difficult to characterize the propagation of airfoil-typed crack and the interference problem of multiple cracks. Up to now, the micromechanics mechanism research of crack propagation of fractured rocks has still been a hot research topic of rock fracture mechanics."

Jan 1, 2015

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By M. N. Vu, G. Armand, A. Noiret, D. Seyedi

Extensive experimental observations have been performed around drifts and shafts at the Meuse Haute-Marne (North-Eastern France) Underground Research Laboratory (URL) to assess the extent and pattern of the induced fracture networks in Callovo-Oxfordian claystone. Two types of fractures can be distinguished, namely; shear (mode II) and extension unloading (mode I) fractures. The main goal of the present paper is to provide insights on the extent of damaged zone around the drifts by numerical simulations. A two-step approach is considered. First, 2D elastic calculations are performed for simulating the excavation of a drift following the direction of the major in situ horizontal stress. The evolution of the stress and strain tensors around drifts are calculated by applying an elliptic convergence function on the drift wall. Two failure criteria are then verified for the induced damage. An equivalent strain and an elastic energy based damage criteria are considered. The obtained results show that the employed simplified approach provides rather good results for the extent of the damaged zone for drifts parallel to major horizontal stress. However, post-processing elastic results leads to overestimating the vertical extent of the damage zone and underestimating its lateral extent, where the in situ stress state is quasi-isotropic in a section of drift. Nevertheless, the obtained results show that an energy based damage criterion could be considered as a potential way for reproducing the extent of the damaged zones if a convergence function can be defined for the drift.

Jan 1, 2015

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015

By N. J. Castilla, R. Giglio

"Circulating fluidized-bed (CFB) combustion technology has been around for over 40 years, but over the last 6 years it has been commercially demonstrated at the 500 MWe scale at the Lagisza plant located in Bedzin, Poland. The CFB at the Lagisza plant has unique first-of-a-kind design features, such as vertical-tube supercritical steam technology and a lowtemperature flue-gas heat extraction that allows the plant to achieve high plant efficiencies of over 43% (net lower heating value). Another unusual feature for a coal power plant is that this plant meets all its atmospheric emission permit levels without any post-combustion de-NOx or de-SOx equipment such as selective catalytic reduction (SCR) or flue-gas desulphurization (FGD).CFB clean coal power technology is entering the utility power sector just in time to help deal with declining quality in internationally traded coals and to promote the large-scale use of economic, low-quality domestic fuels. Owing to the very attractive price discounts, growing supplies of low-quality Indonesian coals are outpacing the supply of high-quality Australian, Russian, and US coals. In Germany and Turkey, the use of domestic lignites for power production provides a secure and economic energy solution while creating domestic jobs.Conventional pulverized coal (PC) boilers will have trouble accepting these off-specification coals because of their narrow fuel specifications; they typically call for heating values above 5500 kcal/kg. This limitation is not an issue for CFB technology because of its ability to burn the worst and best of coals with heating values ranging from 3900 to 8000 kcal/kg.This paper provides an outlook for future coal supply, quality, and price, as well as a review of the technical and economic benefits of CFB technology firing low-quality fuels for utility power generation."

Jan 1, 2015

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By B. Genc

"The risk of spontaneous combustion is well known in the South African coal mining industry. In the coming years it is very possible that the incidence of spontaneous combustion will increase from current levels, due to factors such as an increased rate of mining, re-working of previously mined seams, more stooping and total extraction for underground mines, and higher stripping ratios for surface mines, leading to more spoils. It is also fairly certain that coal mining will face tougher environmental emissions legislation in the near future. To determine the areas where the risks of spontaneous combustion are high, it is necessary to improve on our current laboratory procedures for testing and evaluating coal samples, combining the results with site and field data, and if necessary revising the laboratory rating system to refine our understanding of South African conditions.Currently, laboratory tests are conducted in order to determine both the Wits-EHAC index and the crossing-point temperature which, when combined, give an indication of the spontaneous combustion propensities of the coal samples. This procedure has enabled the establishment of a database of results to review and evaluate South African coal seams. Using this database, the high-risk areas in terms of spontaneous combustion are identified. Tests have been undertaken for five consecutive years, between 2008 and 2012. In total, 119 coal samples from different coal seams and production coalfields have been analysed and classified through a series of laboratory tests. A comprehensive database of these results is available, and is continually being updated as new test results are added. This database will continue to expand, and to provide the basis for an improved risk evaluation methodology for spontaneous combustion"

Jan 1, 2015

By W. Hermülheim, J. Brune

"This paper analyzes mine emergency management and rescue practices in German underground coal mines and compares them to those used in the United States. The German mining industry has developed these practices over more than 100 years, and they have successfully managed numerous fire, water inundation and ground control emergencies using these techniques. The authors interviewed German mine emergency professionals about rescue team and emergency operations. These operations were then analyzed to determine which of these German principles would be of interest to United States mine rescue teams. Implementing these programs into United States mine rescue and emergency operations was analyzed. INTRODUCTION Coal mining has become much safer industry than it has been in the past. Advances in safety and health regulations and company polices have improved working conditions for miners all over the world. Even with these advances there is still a need for continued attention to safety and health. It is also important for mine safety professionals to observe practices and procedures in other countries and cultures and learn what and how to apply this knowledge in their own systems. Coal mine rescue has been an integral part in improving coal mine safety. Mine rescue procedures have evolved with time, experience and technology development. Today, coal mine rescue teams are still needed and must be continually trained and prepared for any mine emergency. Although it is hoped that improved mine safety policies and practices will eliminate coal mine disasters in the future, accidents remind us that disasters can still happen today. In May 2014, Turkey experienced a severe coal mine disaster where 301 people were killed [G.Tuysuz, 2014]. Our industry must learn from these incidents, focusing on disaster prevention and making improvements in mine rescue operations. Mine rescue procedures differ from country to country due different regulatory environments and different historical evolution of emergency response. Sharing practices and procedures from one country to another enables learning from different experiences and cultural backgrounds. Sharing is also a way of preserving information, identifying and learning best practices."

Jan 1, 2015

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By N. Erarslan, M. Ghamgosar

The size of rock fragments depends on the nature of the loading applied the strength of the minerals and the texture of the rock. Research in the literature demonstrates that there is a distinct difference in the rock fracturing process for static and cyclic loading. The tensile strength of brittle rocks is also one of the most significant parameters influencing the rock fracturing process and the propagation of micro-fractures on the crushing, blasting and cutting of rock. The Brazilian indirect tensile test, one of the methods approved by the International Society for Rock Mechanics (ISRM), has been used to determine rock fracture behaviour under different cyclic loading modes. In this study, the dimensions of Brisbane Tuff specimens have been selected according to the method outlined by the ISRM. The main aim of this study is to evaluate the effect of cyclic loading amplitude and frequency on the Fracture Process Zone (FPZ) at the micro-, meso- and macro-scales. The post-failure behaviour of the Brisbane Tuff specimens was obtained under cyclic loading with frequencies varied from 1 to 10 Hz. The amplitude was varied from 10% of Ultimate Tensile Strength (UTS) up to 80% UTS. Laboratory investigations of rock fragment size revealed that different loading frequencies and amplitudes produce different FPZ dimensions. Multivariate Analysis of Variance (MANOVA) results demonstrated that the FPZ dimension is relatively sensitive to the frequency change. Fragment size analysis showed that the FPZ is a consequence of the initiation, propagation and coalescence of micro-fractures and depends on the nature of the loading. Laboratory evidence showed that the FPZ dimension, for the cyclic tests performed on Brisbane tuff, is ranged from 0.07 to 20 mm. The achievement of this study highlights a key finding in the understanding of fracture patterns and propagation models in the FPZ under cyclic loading, which is the dominate mechanical action in the oscillator disc cutter (ODC).

Jan 1, 2015

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015