Search Documents

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By J. Desroches, J. Burghardt, B. Lecampion, A. P. Bunger

"We present detailed comparisons between theoretical predictions and experiments for the initiation of radial hydraulic fractures transverse to a wellbore. Most of these experiments provide a measure of the time evolution of pressure, length, opening and flux entering the fracture during the test. We compare all these measurements simultaneously to our theoretical predictions, thoroughly testing hydraulic fracture initiation theory, which is shown to be predictive. These comparisons notably emphasize the difference between the initiation pressure (the wellbore pressure for which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during the test). INTRODUCTION In this paper, we will compare hydraulic fracturing laboratory experiments performed in different tight materials (PMMA, cement, shale) with the predictions from a numerical solution of the governing equations of hydraulic fracture mechanics (e.g. Geerstma & de Klerk, 1969; Detournay & Peirce, 2014). We focus on transverse radial hydraulic fractures initiating from a radial notch at the wellbore wall (see Figure 1). In particular, we will clarify the difference between the initiation pressure (the wellbore pressure at which the fracture initiates) and the breakdown pressure (a misnomer which simply corresponds to the maximum pressure recorded during a test, usually carried out at constant pump rate). This difference stems from the strong viscous effects at play during wellbore pressurization, fracture initiation and early propagation (i.e. fluid entrance in the newly created fracture). It has been observed on a number of experiments (e.g. Weijers, 1995; Zhao et al., 1996) and has a strong practical application, first because the maximum pressure is the most obvious value to report and second because that maximum value is necessary to specify injection systems."

Jan 1, 2015

By Z. van Zyl

The southern African coal industry is facing the reality that coal reserves are becoming deeper and harder to mine than before. Alternative visions need to be considered to offset the impact of these challenges on productivity, cost, and profitability. One of the main challenges is to maintain current production levels under more difficult conditions, and improve productivity where conditions allow. There is a need to move from the reactive event-based management system towards the more adaptable and flexible process-based management system. This paper focuses on underground coal mining, but the principles are also applicable to other commodities and mining methods. This paper is based on research undertaken by the personnel from Mining Consultancy Services Pty Ltd (MCS) on trends in the underground coal mining sector, as well as practical experience over a period of 16 years in the field of electronic monitoring of mining machinery and productivity optimization.

Jan 1, 2015

By Jin Liu, Torstein A. Utigard

At its Copper Cliff Smelter, Vale Inco Limited processes a bulk copper-nickel concentrate in two Inco oxygen flash furnaces. Coke supplies a minor proportion of the process heat requirements, limiting the flash furnace matte grade to the target 45% CuNiCo. Coke addition to the furnace offers a potential means of establishing a reducing barrier on the surface of the molten bath. Such a practice would be conducive to producing sulfur deficient (partially metallized) matte. At the same iron content, the iron activity of sulfur deficient matte is higher than that of regular matte. A supernatant coke barrier could, therefore, be expected to lead to higher nickel and cobalt recoveries, reduction or even elimination of magnetite furnace bottom build-up and increased sulfur elimination as SO2 in the flash furnace. Extensive experiments were conducted in a miniplant flash furnace to investigate the effect on process metallurgy of the suggested modified scheme. The introduction and description of the experimental set up were given in Part 1 of this paper and an early paper published in Yazawa symposium1 together with the results and some in depth discussion on metallurgy. This paper intends to discuss the kinetics of the miniplant flash furnace testwork.

Jan 1, 2015

By R. T. Jones

"SynopsisScientific progress relies on the publication of ideas and experimental results that can be replicated, tested, and improved over time. The first printed book on metallurgy to have been published in Europe is considered to be De la Pirotechnia, written in Italian by Vannoccio Biringuccio, and published in Venice in 1540. Together with De Re Metallica, written by Georgius Agricola and published in Latin in 1556, this can be considered to mark the start of scientific and technical literature in this field. Scientific publishing of journal papers has been in existence for 350 years, since the world's oldest and longest-running scientific journal, the Philosophical Transactions of the Royal Society, was first published in London in 1665.The nature of scientific societies has changed significantly since the early days when regular meetings were held to discuss science and conduct experiments, and the reading of scientific papers took place, and publication of papers was undertaken to record the proceedings of meetings, often including rather robust debate. In today’s world, there is a plethora of publications, and it is close to impossible for anyone to keep up with the vast flow of information. International conferences with hundreds of presentations have taken the place of the local meetings that used to discuss a single paper or experiment. In this frenetic environment, it is essential that researchers are able to trust the material they read.The system of peer review is used to maintain standards and to improve the quality of papers. This vital system is, however, significantly flawed. There is little incentive for reviewers to invest sufficient time in picking up all errors in publications, and any ineptitude on their part is usually protected by anonymity. It has reached the point where some reviewers have mistakenly permitted the publication of hoax papers deliberately presented with a complicated scientific facade. In light of such astounding inadequacies, perhaps a more open review process would be an improvement. Electronic publishing allows errata to be linked to the original papers.There is an increasing trend towards open access for papers in scientific journals and conference proceedings, which helps to reach as wide an audience as possible. This also supports the statement in the Universal Declaration of Human Rights, which says ‘everyone has the right freely to … share in scientific advancement and its benefits’."

Jan 1, 2015

By P. James

"INTRODUCTION Control of target stream pH is very important in leach mining and treatment of MIW (mining influenced water). On the production side, solution acidity can impact SX (solvent extraction) effectiveness through PLS (pregnant leach solution) and raffinate pH. Many older operations and legacy mining sites generate ARD (acid rock drainage) that is too weak for profitable metal production by conventional means and faces costly wastewater treatment for mitigation and disposal. For wastewater and environmental treatment, neutralization to precipitate and remove metal contaminants to clean the wastewater is the dominant approach. Traditional lime neutralization and precipitation is most often used but results in large amounts of mixed metal sludge requiring costly disposal. Blue Planet Strategies (BPS); which focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources, has developed a new “reagentless” neutralization process. Electricity is utilized in its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform capability to controllably raise target stream pH. The method offers a simple, low-cost approach yielding cleaner treatment chemistry. It can result in less sludge generation and enables possibilities to selectively recover contaminants as potentially saleable products for new revenue generation to offset further offset treatment costs. DEMET Overview BPS’s patented electrolytic DEMET platform leverages solid scientific and chemistry foundations through its advanced design to achieve capabilities and performance not previously realized. DEMET technology combines separated compartment electrolytic cell functionality with proprietary advanced dynamic electrodes and cell configurations to achieve a variety of chemistries and processing targets.[1-6] DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and more cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells."

Jan 1, 2015

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By B. Holen, J. R. Baregi, J. A. Organiscak, A. B. Cecala

The National Institute for Occupational Safety and Health (NIOSH) cooperated with 3M Company in the design and testing of a new environmentally controlled primary crusher operator booth at the company’s Wausau granite quarry near Wausau, WI. This quarry had an older crusher booth without a central heating, ventilation and air conditioning (HVAC) system, and without an air filtration and pressurization system. A new replacement operator booth was designed and installed by 3M based on design considerations from past NIOSH research on enclosed cab filtration systems. NIOSH conducted pre-testing of the old booth and post-testing of the new booth to assess the new filtration and pressurization system’s effectiveness in controlling airborne dusts and particulates. The booth’s dust and particulate control effectiveness is described by its protection factor, expressed as a ratio of the outside to inside concentrations measured during testing. Results indicate that the old booth provided negligible airborne respirable dust protection and low particulate protection from the outside environment. The newly installed booth provided average respirable dust protection factors from 2 to 25 over five shifts of dust sampling with occasional worker ingress and egress from the booth, allowing some unfiltered contaminants to enter the enclosure. Shorter-term particle count testing outside and inside the booth under near-steady-state conditions, with no workers entering or exiting the booth, resulted in protection factors from 35 to 127 on 0.3- to 1.0-µm respirable size particulates under various HVAC airflow operating conditions.

Jan 1, 2015

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By F. Stanley, A. Noble, G. Luttrell

"The supply chain for coal-fired power stations involve a multi-stage network of mining units, preparation plants, blending facilities and transportation systems. Attempts to optimize the supply chain have historically been difficult due to the lack of communication/coordination between the various groups involved in coal production, transportation and utilization. In light of this issue, a new approach for globally optimizing the coal supply chain called Micro-Price Optimization has been developed to simplify the optimization problem and to provide coal producers with fundamental insight needed to improve the profitability of their operations. This fundamental concept assigns unit values to each particles (or groups of particles) passing through production units. Optimization occurs whenever the maximum tonnage of positive value particles are recovered and passed to market, while the minimum tonnage of negative value particles are recovered. Elements considered by the concept include factors such as target boiler cost/efficiency, waste disposal costs, coal quality parameters, emission penalties, transportation charges, or other quantifiable impact factors. This article reviews the basis for the micro-price concept and provides a detailed industrial case study involving the determination of optimum coal qualities that need to be supplied by mine operators to feed a coal-fired power station. INTRODUCTION The performance of coal preparation plants have long been known to play an important role in determining the overall profitability of mining operations. This significance is due to the fact that the misplacement of just 1 ton/hr of clean coal to reject resulting from poor plant performance can represent nearly $300,000 per year in lost revenues for a mine producing a steam market coal (i.e., 1 ton/hr x $50/ton x 6,000 hr/yr = $300,000/yr). This loss can be even more pronounced, occasionally approaching $1 million per year for each 1 ton/hr of misplaced clean coal, for operations producing high-quality coking coal products sold into the premium metallurgical market (i.e., 1 ton/hr x $150/ton x 6,000 hr/yr = $900,000/yr). Detailed economic studies indicate that improvements in plant yield resulting from increases in organic efficiency have one of the largest overall impacts on mine revenue when compared to other cost centers within the mining operation. One of the first studies to show this important financial impact was reported by Norton-Hambleton Consultants (Norton, 1979). Their study indicated that an unfavorable change in plant efficiency was second only to coal transportation in terms of its impact on profitability, while an unfavorable change in the cost of underground mining was a distance third. This longstanding realization has continued to provide a strong financial incentive for coal producers to optimize the separation efficiency of their coal processing and blending operations."

Jan 1, 2015

By R. Lombard

"Water is a very important component in the production process at underground coal mines. Current unfavourable economic conditions have forced the coal mining industry to identify and address every possible bottleneck preventing optimal production. An increase in water-related downtime was identified as one of the bottlenecks at Goedehoop Colliery’s Vlaklaagte Shaft. The purpose of this project was to identify the various causes that contributed to the high downtime (501 hours in 2013, which led to a potential profit loss of R12.9 million) and to suggest possible solutions.After a thorough investigation the main causes of water-related downtime were identified as low water pressure and low water flow caused by pipe leakages and bursts. The main root cause for the low water flow and pressure was identified as being the low pressure resistance (1600kPa) of the thin-walled galvanized steel pipes used in the underground inbye water reticulation system. The pipes were selected according to the previous 1000 kPa pressure requirement for the continuous miner. However, the pressure requirement changed to 1500 kPa, which resulted in the pipes being exposed to much higher pressures than designed for.The water reticulation system was reviewed and current and future underground pipe layout and water requirements were determined for the shaft. The time frame in which the water consumption would be the highest was determined to be between 1 January 2014 and 7 September2014. Machine and sprayer specifications were used to determine theater consumption at the shaft. Three different solutions were considered to solve the water-related downtime problem and to ensure the efficient supply of water to the newly open sections. Permanent underground concrete dams, semi-mobile dams, or new pipe columns with a higher pressure resistance of 3200 kPa were considered. A trade-off study (taking into consideration cost, time to completion and ease of implementation, maintenance requirements, safety, and flexibility) was completed to determine which of these solutions would be most viable.Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Engineering)"

Jan 1, 2015

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By M. Yao, D. Thibodeau

"Selective mining, such as post pillar cut and fill, is used in large, flat, irregularly shaped ore bodies where ground stability is to be maintained. This selective mining is used to open the stope to the full lateral extent of the ore body in order to minimize the dilution and maximise the recovery. For increased mining depth, design of the post pillar becomes more challenging since those pillars will eventually fail as mining progresses upwards. The post pillar should be designed such that failure does not occur at the early mining stage, such as at the first cut. After mining progresses upwards, the post pillars are expected to fail but be confined by backfill. In order to maximise ore recovery, both drift width and post pillar size must be designed adequately with a consideration of all geomechanic parameters. This paper will describe the process used to design post-pillar cut and fill for one of the ore bodies in Vale’s Copper Cliff Mine using a combination of both empirical deterministic and numerical modelling techniques. By utilizing both empirical deterministic and numerical modelling techniques drift width and post pillar size can be effectively designed. Current post pillar cut and fill design in the existing Vale operations are used to validate the design for Copper Cliff Mine. INTRODUCTIONCopper Cliff Mine is located within the Copper Cliff Offset in the limits of City of Greater Sudbury, Ontario, Canada, as shown in Figure 1. The Copper Cliff Offset extends about eight kilometres south from the Sudbury Igneous Complex into the footwall rocks. Until 2008, the current Copper Cliff Mine was operated as two separate mines i.e. North Mine and South Mine. However, as part of restructuring of Vale Ontario Operations, the North and South Mines were merged in 2009 to form the “Copper Cliff Mine”."

Jan 1, 2015

By D. J. Zuliani

A mass and energy balance for a modern electric arc furnace ("EAF") indicates that about 70% of the process energy losses are contained in the off-gas as chemical energy in the form of uncombusted CO and H2 and as thermal energy. Given the magnitude of the off-gas energy losses, improved EAF energy efficiency needs to focus first on controlling furnace practice to maximize "in-EAF" energy utilization and second, on recovering residual energy in the off-gas existing in the fume system. This paper focuses on the application of off-gas analyzers, sensors and process models to control and optimize "in-EAF" energy utilization efficiency. The paper will also discuss the application of heat recovery technology to EAF steelmaking.

Jan 1, 2015