Search Documents

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By Minting Li, Hailong Yang, ChangWei, Cunxiong Li, Gang Fan, Xingbin Li, ZhiganDeng

The filtration problems on acid leaching sludge of high silicon zinc ore have been paid extensive attention in zinc hydrometallurgy. It was found that soluble silica can be effectively converted into silica precipitate with good settling, filtration and washing properties, and the filtration rate can be in excess of 800 L/m2 · h under certain leaching conditions. According to investigating on the filtration rate, viscosity and concentration of silica of leaching sludge or liquor, the filtering temperature can tremendously improve the filtration property of pulp. At the same time, the experimental data indicated that the viscosity of leaching liquor was the key factor influencing filtration property of leaching sludge.

Jan 1, 2016

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Bo Liang, Hongmin Zhu, Kai Huang, Shafiq Alam

A new approach of recovering platinum and palladium from electronic wastes by hydrochloric acid leaching followed by selective adsorption on low-cost and environmentally benign biomass sorbent prepared from easily available agriculture waste is suggested. The obtained adsorbents were prepared by a combination of chemical modification and hydrothermal carbonization process with (NH4)2C2O4. It was found that the maximum adsorption capacity of hydrothermal carbonized garlic peel for Pt( ) and Pd( ) was 1.64 and 0.42 mol/kg respectively. The Langmuir adsorption isotherm was applied to describe the adsorption process. Kinetics of the Pt( ) and Pd( ) ions adsorption was found to follow pseudo-second-order rate equation. The adsorbents were examined by scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FT-IR). Based on the characterization results, a possible mechanism of Pt( ) and Pd( ) ions adsorption with the hydrothermal carbonized garlic peel was proposed. This study provides a promising adsorbent with efficient adsorption property for platinum and palladium recovery from the leach solution of electronic wastes.

Jan 1, 2016

By Edmundo Manilla, Merete Tangstad, Daniel Davila, Eli Ringdalen

FeMn alloys are typically produced with lumpy ore or sinters. Minara Autlan, the Mexican FeMn producer, is however making Mn-nodules as a raw material for Mn-alloy production. The Mn nodules have been characterized by XRF, XRD, by wet chemical methods and by EPMA. The Mn/Fe ratio is somewhat lower compared to commercial Mn ore on the marked. The basicity of the ore is however close to 1, and additional fluxes may not be used. The Mn-nodules will be in a state of manganosite (MnO), tephroite ((Mn, Ca)2SiO4) and galaxite ((Mn,Mg)Al2O4). This leads to a low melting temperature area. A low porosity and low amount of higher Mn-oxides gives a high thermal strength to the nodules.

Jan 1, 2016

By Y. Wang, L. Liu, G. Xu, Y. Lv J. Sheng H. Zhang

In order to increase the service life of large scale coke dry quenching furnaces, the damage mechanism of lining was investigated, and the structure and properties of lining refractories used in cooling section were researched. The results showed that the abrasive wear volume of lining bricks at one fourth height section under skew tunnel was smaller than other sections. The wear loss of mullite brick and dense clay brick used in the lining of cooling section were respectively 8.02 cm3 and 11.65 cm3 in fifteen minutes. The mullite brick was laid with clay brick alternatively. By the different wear rate, the surface of lining was rough and uneven in the later service life, and short brick was easily dropped from lining. During the service, the basis wore off more easily than the aggregate. It is necessary to improve the wear resistance property, which will increase the service life of cooling section’s lining for coke dry quenching furnaces.

Jan 1, 2016

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Caryn Wendt, Donna Post Guillen, Armando McDonald, Erik R. Coats, Chaston Ellis, Kevin Feris

Dairy operations constitute ~2.5% of annual U.S. greenhouse gas (GHG) emissions, making dairies one of the largest sources of industrial GHG emissions. We are developing a novel, integrated system to achieve a net reduction in dairy GHGs while producing value-added materials and products. This integrated manure-to-commodities system converts dairy manure to bioenergy, sequesters carbon by converting volatile fatty acid-rich fermenter supernatant to bioplastics, and utilizes anaerobic digester (AD) and polyhydroxyalkanoate (PHA) reactor effluents to produce algae that can be harvested and internally recycled to enhance PHA production and sequester carbon. A decision-making tool is being developed for the integrated system that quantifies net GHG reduction, carbon sequestration, nutrient management and economics.

Jan 1, 2016

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By M. Wenzel, Dang Thanh Tung, Nguyen Anh Duc, Nguyen Huu Luong, Dang Van Sy, N. Kelly, K. Gloe, K. Kretschmer, Phuc Nguyen Le, K. Schnaars, S. Robles M, L. Götzke, J. J. Weigand

The recovery of rare earth metals from secondary sources has attracted much attention due to their ever expanding demand in the high-tech industry. The studies reported here focus on the hydrometallurgical recovery of lanthanum and cerium from spent fluid catalytic cracking (FCC) catalysts in a two-step process: leaching with nitric acid and solvent extraction by tri-n-butyl phosphate (TBP) and di(2-ethylhexyl)phosphoric acid (D2EHPA). The experiments show a high dissolution yield of about 93% lanthanum and 42% cerium in a single leaching step with 2 M (126 g/L) HNO3 at 80 °C; only 11% aluminum has been dissolved simultaneously. In the subsequent solvent extraction step the best results for this leach liquor could be achieved using a 1:1 mixture of 25% (v/v) TBP (0.92 M) and 25% (v/v) D2EHPA (0.76 M) in n-decane without the need for any pH adjustment. In that case La(III) and Ce(III) can be extracted with 60% and 74% yield respectively in one stage from the majority of accompanying matrix elements. In particular no extraction of Al(III) could be observed under these conditions.

Jan 1, 2016

By Shengfan Zhou, XUEWEN WANG, Bianfang Chen, Mingyu Wang

Vanadium was leached from roasted stone coal by NaOH solution, and the effect of leaching temperature, leaching time, addition of NaOH, liquid to solid ratio, the grinding fineness of stone coal, and stirring speed on the vanadium leaching rate was studied. The kinetics analysis for the process is presented by the shrinking core model. The results show that the vanadium leaching ratio of roasted stone coal can be beyond 75% at the 6% NaOH addition, leaching temperature of 95°C, leaching time of 7h, liquid to solid ratio of 1.2mL/g, and grinding fineness of 0.111mm. The leaching process is controlled by interfacial reaction kinetics and the apparent activation energy was 59.36kJ/mol.

Jan 1, 2016

By Zhengjie Chen, Wenhui Ma, Jijun Wu, Kuixian Wei

The gasification reactivity of PC (petroleum coke), strengthened by addition of different potassium carbonate proportions using different grinding medium, was investigated by using thermogravimetric analysis (TGA). Results showed that the gasification reactivity of PC not only increased with the increase of catalyst-loaded, but also showed the effective improvement by anhydrous alcohol. The PC was mixed with potassium carbonate [K2CO3] catalyst at 0.5%, 0.8%, 1.0% and 1.5%, and then ground wet with distilled water. The CO2-gasification rate of PC was only 77.35%, 80.55%, 84.07% and 85.88% under the gasification temperature 1100 °C and holding time 120 min, at different K2CO3 respectively. However, when the PC was ground in anhydrous alcohol at the same condition of catalyst-loading, the gasification rate of PC reached 95.43%, 96.63%, 95.50% and 95.61% at the holding time of 108 min, 101 min, 74 min and 35 min, respectively. It was shown by FTIR, SEM and EDX determinations that the anhydrous alcohol used as the grinding medium can further improve the gasification reactivity of PC when compared with the distilled water.

Jan 1, 2016

By Qiang Zhong, Bin Xu, Qian Li, Wei Gao, Yongbin Yang, Yaxuan Wang

Lump coal with high volatility is used for providing heat and reductive gas, and ensuring permeability in COREX. However, it is apt to be pulverized in transport and storage process. Therefore, comprehensive utilization of the pulverized coal to produce coal briquettes with appropriate binders is significant, among which the molasses binder cannot meet the technological requirements. In this paper, coal tar pitch binder and BJ additive were used in briquetting and carbonizing process of coal powder. The results showed that BJ effectively activated cold state cohesiveness of the pitch and make it bond the coke particles to a firm briquette at room temperature .Carbonizations of coal and coal tar pitch achieved obvious constriction and formed a carbonized skeleton. The drop resistance of wet briquettes reached over 50 times/1meter. When cured at 1000 °C for 1h under nitrogen atmosphere, the compressive strength of carbonized briquettes came to 6.43 Mpa.

Jan 1, 2016

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Yuanbo Zhang, Zhixiong You, Li Qin, Guanghui Li, Tao Jiang

Low-grade manganese oxide ore is generally characterized by high iron content. In this work, sulfidation roasting of an iron-rich manganese oxide ore with elemental sulfur was characterized. The experimental results indicated that manganese dioxide can be selectively reduced over iron oxide by using elemental sulfur. The manganese phases in roasted product included low-valence manganese oxide, manganese sulfide and manganese sulfate, while those of iron mainly depended on the sulfur addition. Iron oxide would only be reduced or sulfidized at larger sulfur additions. The effect of roasting temperature and S/Mn mole ratio on the phase transformations was also investigated; extractions of Mn/Fe by sulfuric acid were evaluated. An extraction of Mn greater than 95% was obtained while that of Fe was controlled less than 10% under the optimal conditions.

Jan 1, 2016

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016

By Xiaoyan Xiang, Wenqiang Yang, Wentang Xia

Magnesium aluminate spinel is widely used in the metallurgical industry as refractory material, however, natural magnesium aluminate spinel is rare and most of the magnesium aluminate spinel is synthetic. The traditional synthesis of magnesium aluminate spinel often needs high temperature, which leads to more energyconsumption. In this article, solid phase sintering process was employed to synthesize magnesium aluminate spinel, in which, magnesium and aluminum oxide were used as raw materials and magnesium and aluminum powder were used as composite additives. The mass ratio of magnesium and aluminum on the effect of synthesis of magnesium aluminate spinel and the characteristic of the synthesis at different temperature and time was discussed. Experiment found that the synthesis temperature was observably lowered when the addition of magnesium and aluminum was 2.0% and 1.0% respectively.

Jan 1, 2016

By Yuanbo Zhang, Bingbing Liu, Zhuyin Chen, Xiao Kang, Chen Liu

Composite agglomeration process (CAP) is an effective method to utilize the iron-bearing dusts generated in the ironmaking plants, by which the dust percentage in the sinter feed can be increased up to 20 wt %. In the current study, a comparison on behavior of iron-bearing dust in the conventional sintering process (CSP) and CAP was characterized. The results showed, in the CSP products, the scattered iron-bearing dust in the mixture was disadvantageous for the sintering indexes and consolidation of the finished sinters. In the CAP products, the main phase in the iron-bearing dust pellets was well-crystallized Fe2O3 grain particles. In the matrix parts, there were more Fe3O4 particles generated, which caused to high RDI+3.15 and low RI of the finished products. The pellets and the matrix parts were bonded by iron oxides and acicular calcium ferrite.

Jan 1, 2016