Search Documents

By John Stewart

The market at present supplied by shipments from the phosphate districts of Quebec, Ontario, and New York State requires high-grade ore, carrying from 75 per cent. to 90 per cent. of phosphate of lime. In sorting out such material by hand, much valuable phosphate is necessarily left in the "culls" or refuse, besides which, much phosphate-rock of low-grade is not now mined at all, because it cannot be made available by the crude method of cobbing and hand-sorting. The utilization of such material, which would, of course, greatly benefit this industry, requires either a mechanical separation or a chemical process which would concentrate the phosphate in a form suitable for agriculture. Considering the rich phosphate now shipped as the first class, we may arrange the lower grades in three classes, as follows: Second Class.—Cull-ore from the first class, and the mass of deposits having, as gangue, pyroxene or hornblende. The following table gives the hardness and specific gravity of the minerals concerned: Hardness Spec. gravity. Apatite,....... . 5 3.1 to 3.25 Crystalline limestone (pink calcite),. 3 to 4 2.5 to 2.9 Pyroxene,..5 to 6 3.23 to 3.5 Hornblende,.5 to 6 2.9 to 3.4 Feldspar (orthoclase),. .. . 6 to 6.5 2.5 to 2.6 It is evident that when pyroxene and hornblende are present in large proportions, this ore cannot be successfully concentrated by crushing and jigging. It may be reduced to fine powder by successive treatment in a rock-breaker and a Sturtevant or Frisbee-Lucop mill, or other suitable apparatus, and in this condition it could be largely used by applying it freely upon exhausted clay soils, such as occur in Quebec and Ontario. The occupants of these once fertile river-lands are, however, hard to move in the direction of such improvements. When water-power is at hand, the cost of crushing

Jan 1, 1893

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By Axel Sahlin

Having no business interest in any of the various machines used for granulating ores, my remarks on the subject are prompted solely by my desire to contribute towards the determination of the best apparatus such information, as I have been able to gather,

Jan 1, 1893

By Francis Freeland

An examination of accessible English literature shows that but small space has been allotted to the determination of faults ; most suggestions being confined to Schmidt's rule of the downthrow on the hanging-wall of the fault, or the coal-miner's rule of the obtuse angle. Von Carnall's modification of Schmidt's rule is sometimes given without the important exception, and Zimmermann's rule is

Jan 1, 1893

Jan 1, 1893

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By D. H. Bacon

Our Transactions contain so many suggestions of apparently trivial, yet really important, contrivances for the saving of time and

Jan 1, 1893

By T. A. Rickard

The earlier paper (Trans., xx., 463) describing this Victorian mining district, to which the present is supplementary, was mainly confined to the consideration of the "saddle-reefs," as scientifically the most interesting and economically the most important of the

Jan 1, 1893

By F. H. McDowell

The increasing interest in the subject of electrical separation warrants the addition to what has already been written of a few lines covering the practical workings of the Tilly Foster mill under the direction of Mr. E. S. Moffat, General Manager. Since my last paper was presented to the Institute, Mr. S. P. Tomkins, the superintendent, has had thrust upon him for solution several problems complicated by the introduction of new conditions. 1. The richer portion of the lean ore dump, and that nearest the railroad track, having been worked up in 1890, the handling of the balance, including a largely increased amount of rock, could only be accomplished at an increased cost. 2. The tailings had accumulated close about the mill to such an extent that arrangements had to be perfected to move them further away.

Jan 1, 1893

By William H. Morris

At the Glen Summit meeting, the question of controlling the silicon in pig-iron WAS raised; and as this has been deemed by most furnace-men for years past a matter of special difficulty, an account of our experience in the matter may be of interest. When running on mill-iron, some years ago, we aimed to keep

Jan 1, 1893

By Fred W. Gordon

Apart from the character of pig-iron to be manufactured, other than that it shall be well reduced and open-grained, the selection of the materials should be such as to produce it at the lowest cost. As a rule, the sources of fuels and limestones are not so extensively varied as those of the ores. Many Eastern furnaces are now using Lake Superior ores, and but recently a part of the supply came from foreign ports. It is, however, of the highest importance that the character of fuels and limestones, as well as ores, should be carefully considered in determining their value and making judicious selection among those available. The formulas here offered are based upon the assumption that the heat-requirements for a given mixture are measured by a constant required by the oxide of iron, added to that required for a unit of slag, multiplied by the weight of that slag per unit of iron. The heat-requirements for oxide of iron per unit of pig-iron made are assumed to be 2854 centigrade units. This is taken from the careful analysis of Sir Lowthian Bell, and, so far as the writer is able to determine, is very nearly correct. Dividing this by the quantity of heat that may be evolved and utilized within the furnace per unit of carbon, determines the quantity of carbon required per unit of pigiron ; and if to this be added the quantity of carbon absorbed by the pig-iron, the total requirements in carbon are determined, on the assumption that pure oxide of iron is reduced with pure carbon by the ordinary process of the blast-furnace. Calculating the quantity of slag that would be made from a given mixture of ores, smelted with a given impure fuel and fluxed with a given impure limestone, multiplying this weight of slag by the heat-requirements of its unit (taken at 1050 C. H. U.), and dividing the product by the heat-units evolved and utilized within the furnace per unit of carbon, will determine the quantity of carbon required per unit of pig-iron for the slag.

Jan 1, 1893

By Carl Henrich

Jan 1, 1893

By Davis Baker

The direct-metal cars or ladles of the Maryland Steel Company have a capacity of 18 tons when filled within 12 inches of the top. On account of this large capacity, the formation of skulls in these ladles is by no means as rapid as in smaller ladles; but a skull once formed is a very unwieldy piece of metal to handle, and especially to remove from the ladle. We have found it cheaper to clean ladles often rather than make very heavy skulls. We aim to keep the ring of chilled metal that forms on the surface of the iron chipped off, so that the skull shall form principally at the bottom until it becomes so thick as to render the ladle unfit for service. Sometimes it happens that a ladle may be held for several hours filled with molten metal. This invariably leaves a large amount of chilled metal in the ladle. Frequently the skull will weigh several tons, and will be of the full size of the ladle inside, with a top crust, having perhaps a hole 12 inches square, through which the molten metal was poured. In order to remove skulls that cannot be easily chipped out with a bar, we use what may be called a skull-extractor, consisting of a hydraulic cylinder mounted in the center of a heavy cast-iron plate, standing vertically on a suitable foundation. Figs. 1 and 2 show the construction and operation of this apparatus, Fig. 1 being a view of the extractor with pistons extended to full stroke, and Fig. 2 a view with ladle in position and pistons about to commence the stroke. in both figures, A is the hydraulic cylinder, B the vertical cast-iron plate, and C the foundation. The water-pressure, admitted through the pipe, P, is 750 pounds per square inch, and the inside diameter of A is 14 inches. There are two pistons: D, fitting the bore of the cylinder, and E, 84 inches in diameter, moving inside of D. Both pistons move together when

Jan 1, 1893

[Note.—The paper of Mr. Hoffman on " Practical Results in the Magnetic Concentration of Iron-Ore " (page 602); that of Mr. Langdon on "The Use of Magnetic Concentrates in the Port Henry Blast-Furnaaces" (page 599); and those of Mr. Landis on "The Determination of Iron in the Tails from Magnetic Concentration " (page 609) and "Note on Sampling Iron-Ore" (page 611), were all prepared as contributions to this discussion.] The papers of Mr. Langdon and Mr. Hoffman were presented. W. H. Hoffman, Croton Mines, N. Y.: I will add a few remarks, by way of answer to inquiries for further details. The Croton Mines are particularly well located for cheap mining. The ore-bed is very large, and so lies in relation to the railway tracks of the Harlem and other railroads that a very large proportion of our mining for several years to come can be done above these tracks. The concentrating-mill is now 400 feet from where we are working in the quarry. In blasting we never remove less than 2500 tons at a blast,

Jan 1, 1892

By Charles M. Rolker

The main tin-producing regions of the world are known to be England, Australia and the Dutch East Indian possessions, chiefly Banca and Billiton. During recent years, the tin of the Malay Peninsula, exported from Penang and Singapore, has been coming prominently to the front. France, Austria, Hungary, Germany, Spain, South America, Russia and China still present insignificant figures. The conspicuous part which the Dutch possessions in the Indian Archipelago have taken in supplying the world with tin, is well known. Tin was discovered in Banca as early as 1710, and has been produced there ever since; but the supply has been most important since Banca came fully into the possession of Holland, in 1821. In Billiton and the adjoining island of Singkep, the existence of tin was known prior to 1822.* The Lingganese knew of its existence in the valley of Embalong, from creeks and streams in the neighborhood of Tima and Simper hills, on Billiton and also on Singkep island, but the prevailing superstition that tin-mining brought misfortune, influenced them to let this industry lie idle. The attempts of the Dutch government to test this question were lukewarm, perhaps by reason of the fear of reducing, through new discoveries, the price of Banca tin, and the island was abandoned in 1826, leaving only a military post. In 1850, Dr. Crookewit, a chemist and naturalist, was sent out to verify the rumors that tin existed in Billiton. His report was unfavorable; but in 1851 Mr. C. De Groot, a mining engineer, found tin readily, and the active work on Billiton dates from that time. Less than 600 tons were produced during the first ten years, and 3000 tons in the next decade. Billiton tin-mining is done by

Jan 1, 1892

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892

By John C. Smock

The rich deposits of magnetic iron-ore in the Highlands of northern New Jersey attracted the attention of iron-workers at the time of the earliest settlements in that region. The outcrops of the oreshoots at the Dickerson mine, at Mount Hope, and at Hibernia, in Morris county, and at Ringwood, in Passaic count,y, which were doubtless such as would lead to discovery, location and development of nearly all the large iron-mines in that part of the State, appear to have had their beginnings where the ore cropped out on the surface or where it was scarcely concealed by a thin mantle of earth. In the early history of New Jersey iron-mining, the careful explorations and surveys made by the agents of the famous London Com-

Jan 1, 1892

By John Birkinbine

Four meetings of the Institute have been held in the anthracite coal-fields of Pennsylvania, and excursioris into the district, in connection with meetings elsewhere, have familiarized our members with

Jan 1, 1892

Jan 1, 1892

By M. B. Holt

At this time, when electricity in its various applications is attract- ing so much interest, and with such good reason, it has been suggested to me that, as the Aspen Mining and Smelting Company, of Aspen, Pitkin county, Colorado, was the first mining company in America to employ electrical power for hoisting, a record of what has been accomplished by this company would be of interest. Early in the year 1888 the question of power for the development of the ore-horizon lying below the level of the tunnel through which the property is worked, became one of importance. The conditions under which it was proposed to use power were as follows (See Fig. 1): The company's mines lie upon the northwestern slope of a mountain, the ascent of which is at an angle of 28' from the horizon. The ore, consisting of argentiferous galena and other silver-bearing mineral, is found at or near the plane of contact of a superincumbent mass of blue limestone, with an underlying bed of dolomite. This contact plane dips north 30° west, at an angle of 60' with the horizon. A tunnel 1000 feet in length, driven south into the mountain near

Jan 1, 1892