Search Documents

By S. P. Godby, S. P. Sharples

Wind-tunnel tests were carried out of the conditions under which nuisance dust particles (100-1 000 micrometres) become entrained by wind. A laser entrainment monitoring system (LEMS) was used, and was found to provide an accurate means of assessing nuisance dust emissions from a surface. Accurate determination of the threshold entrainment velocity of dusts using the LEMS gives a baseline against which the performance of dust control techniques can be evaluated. Minerals tested included coal, petroleum coke, limestone, sand and pulverised fuel ash. Pilot field trials of a portable wind tunnel equipped with the LEMS have been successfully completed, providing a means of validating laboratory results in the field

Jun 19, 1905

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By T. M. Williams, P. M. Green

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The sediment geochemistry of streams draining Southern Uplands and Lake District turbidites was compared with lithogeochemical data for the source greywackes, using stratigraphically defined catchments. Several systematic trends in element abundance variation between source and stream sediment can probably be applied more widely to interpretation of drainage geochemistry. Pb and Zr increase markedly from source rock to sediment, by adsorption on clay and zircon grain concentration. Variation of feldspar-related elements Rb, Sr, K and Ba appears to be controlled by source grain size and compositional maturity. Ni shows surprisingly little change and Fe and Co are only slightly raised. Cr is particularly useful, with variations superimposed in anomalously high regional levels. Abrupt changes in Cr distribution in stream sediment coincide with stratigraphical boundaries, allowing drainage data to be used as a surrogate for whole-rock values

Jun 19, 1905

By J. K. Whyatt, W. P. Blake, T. J. Williams

A study at the Idaho mine revealed that, despite the apparent randomness of seismic events, common characteristics defined five recurring types. These characteristics included the geological structure that slipped, the first-motion pattern and the location and intensity of damage. Many large events caused little or no damage, and where it did occur it was concentrated at intersections between slipping structures and mine openings. Of 39 events between 1989 and 1994 with local magnitudes of 2.5 or more, 10 were caused by slip on bedding planes in the southern limb of the mine, 6 occurred near the vein along a set of near-vertical faults that form the central shear zone, 8 were strike-slip events on the Southern Control Fault, 4 were by slip on the vein itself and 10 involved strike-slip and/or dip-slip movement along the North Control Fault. Strategies for control of mining-induced seismicity need to consider all five types of event, lest a strategy to reduce one type increases others

Jun 19, 1905

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905

Paper presented at the UK minerals industry conference and published in: Minerals extraction towards the millennium. UK minerals industry conference, 3-5 April 1995, University of Leeds. London: Institution of Mining and Metallurgy, 1995. The various types of risks that arise in minerals industry projects are usually financial, technical, or environmental, and the key to valid risk analysis is complete integration of all risks, both within and between categories. Geographical information systems (GIS) and geostatistical simulation methods can provide a means of integrating data and conducting realistic risk analyses. Risk can be quantified but there are limitations to numerical approaches to risk assessment. Realistic quantification requires adequate models of the processes that give rise to risk. Risk perception must also be taken into account when conducting risk assessment and reporting the results, especially in public forums. The modelling and visualisation capabilities of a combined GIS/simulation system can provide the means of dealing with perception in risk analysis

Jun 19, 1905

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By P. H. Morris

The exponential delta profile equation matches the profiles of a wide range of coal and metalliferous subaerial tailings deltas well, but the original model implies unrepresentatively low solids concentrations. A revision, based on analysis of the governing equations of mobile bed flows with high concentration values, has shown that for exponential delta profiles to form there must be quasi-steady, slowly varying flow and slow deposition as well as tailings with a log-uniform sorting-parameter distribution. Deposition on tailings deltas is slow and the flow in many natural streams and, by analogy, tailings deltas is quasi-steady and slowly varying; the assumption of such flow is justified by the strong congruence of the revised model and the available data. The predictions of the theoretical model are essentially unchanged but concentration and flow Froude number are now not explicitly limited

Jun 19, 1905

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By R. M. Cooper, H. K. Herbert, D. N. Phillips

A study was carried out to determine the effects of adding CaCO3, Fe, Al and CaSi2 to the ladle, rather than to the raw materials, in order to increase the concentration of Ca, Fe and Al in the final product to meet customer specifications at Simcoa's Kemerton plant in Western Australia. LA-ICP-MS, SEM-EDXRA and ICP-AES analysis of samples and controls showed that the technique is suitable for controlling minor element concentrations. Iron was successfully added, while calcium silicide with aluminium proved better than limestone with aluminium for controlling Ca and Al concentrations in the silicon

Jun 19, 1905

By A. M. Tunstall, N. Djordjevic, H. A. Villalobos

The damage zone behind a typical smooth-wall blast in the open pit was assessed by visually examining diamond drill core to identify blast-induced cracking, mapping core rock quality designations to identify changes in fracture frequency and conducting uphole seismic testing to determine changes in rock mass characteristics. The results from the three techniques show reasonable correlation. They suggest that major damage, in the form of fracturing of intact rock, occurs at least 7 m behind the smooth-wall blast and significant damage, in the form of opening and extension of calcite-filled fractures, at least 12 m from the blast. At greater distances the dominant damage mechanism is the loosening of existent joints within the rock mass. In the trachytes at El Soldado these damage mechanisms correspond to peak particle velocities of 2 000, 900 and 500 mm/s respectively

Jun 19, 1905

By F. M. Vokes, P. M. Ihlen

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Ore deposition was related to three major stages: continental rifting and separation (Vendian-Late Cambrian), convergence (Late Cambrian-Early Silurian) and collision (Early Silurian-Devonian). The first stage included deposition of volcanogenic massive sulphide Zn-Cu and stratabound or stratiform Fe and Zn-Pb(-Cu) on continental margins, as well as less economic Nb and Fe in carbonatites, U, Mo, Ni and V in Alum Shales and orthomagmatic Cr, Fe-Ti and Ni(-Cu). The numerous volcanogenic massive sulphides formed during convergence included Early Ordovician Cu-Zn, mature-arc Cu, Zn, Pb and Fe-oxide deposits, Besshi-type deposits dominated by Cu or Zn in gabbro-intruded sediments and minor Cu-Ni(-PGE), Cu-Mo and skarn deposits. The collisional stage is represented by epigenetic deposits including sandstone Pb deposits (Pb, Zn, Ba, F and Cu) and minor vein deposits with variable Au, Ag, Pb, Cu, Zn, Fe, As, Sb, W and Mo

Jun 19, 1905

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By L. Villa, O. Suarez, D. Arias, L. G. Corretge

The deposit comprises two vertical, lenticular bodies emplaced in the allochthonous block of a Variscan thrust. Epigenetic mineralisation occurs as replacement of carbonated volcaniclastic rocks of Cambro-Ordovician age. The dominant sulphide minerals are sphalerite and galena with minor chalcopyrite; the main non-metallic mineral is quartz and there is hydrothermal silicification, chloritisation and sericitisation. Sulphur isotope values for sphalerite and galena are heavy and reflect the fundamental relationship between delta-34S in ZnS and in PbS, suggesting isotopic equilibrium. Four sphalerite-galena pairs yield temperatures between 163 and 218 degrees C, in good agreement with the 187-207 degrees C estimated by the Ga/Ge-sphalerite geothermometer. The ore sulphide was leached by the hydrothermal solution from diagenetic pyrite in the host rocks and disseminated sphalerite and galena in Cambrian carbonates

Jun 19, 1905

By I. W. Farmer

High horizontal stresses and high horizontal to vertical in-situ principal stress ratios in the plane of underground drifts and entries can damage weakly laminated roof rocks quite severely. Such stresses are difficult to measure accurately, as illustrated by case histories of in-situ stress measurement at Wistow and Lea Hall mines, in the UK. Their direction and relative magnitude can, however, be estimated from the absolute velocity vectors of continental plates. With the preliminary results from the World Stress Map project now available it is possible to indicate mining areas where regional horizontal stresses are low, such as Europe, and high, such as Australia and Asia

Jun 19, 1905