Search Documents

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By Robert T. Mann

This paper is one of a series being prepared for and published by the United States Bureau of Mines on the quarrying, crushing, and grinding of limestone for cement manufacture. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total coats. It is recognized that publication of total costs might in many instances cause embarrassment to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. B. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1933

By Mayer G. Hansen

A series of papers dealing with diamond drilling practices, compiled in accordance with an outline prepared by engineers of the United States Bureau of Mines, is to be published as information circulars by the bureau. This paper, the first of the series, describes the general practice at the United Verde mine during the last ten years; specific instances cited in the paper refer to 1930, the last year of full operation. The United Verde copper mine is located at the town of Jerome, Yavapai County, north central Arizona.

Jan 1, 1933

By Dudley Homer

MINAS DE MATAHAMBRE, S.A. is a Cuban mining corporation with mines located in the Matahambre district about 100 miles westerly from Havana in the Province of Pinar del Rio. The port of entry is the subport of Santa Lucia on the north coast of Cuba. The mines are located six miles inland at the town of Minas de Matahambre. Minas de Matahambre and Santa Lucia are connected by a 9-mile automobile road, and a 30,000-ft. Leschen aerial tramway. At the subport of Santa Lucia the company maintains docks, concentrate bins, tugs, lighters, and miscellaneous shipping equipment. The power plant of the company is also located at Santa Lucia. Connection between the power plant and the mine is effected by a 30,000-ft. transmission line. In the town of Minas de Matahambre are located the mines, concentrator, shops, and warehouses. The con-centrates are transported to Santa Lucia by the Leschen aerial tramway. The mines are equipped with three shafts, viz., Nos. 1, 2, and 3. (Fig. 1.) No. 1 Shaft is a three-compartment vertical tim-bered shaft and has reached a depth of 1825 ft. This is the present main hoisting shaft. No. 2 Shaft is a four-compartment vertical shaft lined with steel sets and native hardwood lagging. Certain portions where the ground is heavy have been lined with re-inforced concrete. Practically all production will be hoisted eventually through this shaft. No. 3 Shaft is a three-compartment vertical timbered shaft. It has reached a depth of 1090 ft. Its purpose is for prospecting, ventilation, and handling men and sup-plies through the north section of the mine.

Jan 1, 1933

SPEAKING generally, it may be said that leaching is the simplest method of recovering copper from its ores. Likewise it is perhaps the oldest method of treatment used by copper metallurgists of the modern era. Reliable records indicate that as early as 1752 cupriferous pyrite was leached in the famous Rio Tinto region in Spain. Though the manipulation was quite different from that in use today at Chuquicamata, New Cornelia, Inspiration, and Andes, it resembled that employed by Phelps Dodge at Bisbee, as described in Chapter XIV. Leaching consists of subjecting ore to the action of a liquid solvent or menstruum (usually an aqueous solution) which dissolves the major part of the soluble copper minerals. The resulting pregnant solution is drained off or otherwise separated from the residual ore; and the copper in the solution is then recovered by some appropriate means of precipitation. When sulphuric acid is the lixiviant, as is usual, the simplest procedure is to pass the copper-bearing solution through large troughs containing scrap iron. The iron displaces the copper in the solution, precipitating it as a slime coating the iron and varying in color -from bright copper to a dull black. This may be washed off at intervals, collected as a sludge, dried, and melted with a little fluxing material to produce reasonably pure copper. Usually, of course, the mud is sent to a smelter where most often its destination is the converter or reverberatory furnace. Modern practice uses precipitation on iron only as a complemental process to electrolytic precipitation or deposition, wherein the pregnant copper-bearing solution, acting as the electrolyte in a cell having insoluble anodes and copper cathodes, is depleted of the copper it contains. Cathode copper, 99.5 per cent pure, is produced ready for the market as refined copper, or for a simple process of melting, fire-refining, and casting in

Jan 1, 1933

By R. L. Marek

The number of persons fatally injured in the California petroleum industry, in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry--reduced personnel, decreased active field development, and curtailed production--have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period.

Jan 1, 1933

By W. S. Dyer

Introduction In northern Ontario, refractory clay is found on four rivers of the James Bay watershed: the Abitibi, the Mattagami, the Missinaibi, and the Moose. The clay all belongs to the same geological formation ( the Mattagami of Lower Cretaceous age) , and occurs within a structural depression or 'basin', the boundaries of which have never been defined but which appears to cover at least 1,500 square miles of territory. The recently constructed James Bay extension of the Temiskaming and Northern Ontario railway crosses the northeast end of the basin at the Onakawana lignite field, which by rail is 126 miles north of Cochrane, 605 miles north of Toronto, and 60 miles southwest of Moose Factory. Smoky Falls, the northern terminus of the railway owned by the Spruce Falls Power & Paper Company, Limited, is 7 miles south of one other point in the basin, i.e., the outcrops of refractory clay, sand, and kaolin at the foot of Long rapids on the Mattagami river. Smoky Falls is 50 miles north of Kapuskasing. In a very early report(l) , Dr. Robert Bell, of the Geological Survey of Canada, described '"light coloured marl in horizontal beds" from the Missinaibi river, and noted that the lignite also occurring in the river was probably :associated with the marls. This was undoubtedly the Cretaceous refractory day. Other early writers noted the occurrence of fire-clays, but it was not until Joseph Keele(2), of the Geological Survey, visited thee region in 1919 and studied the clays that their real significance was known.

Jan 1, 1933

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to can and ore rate mines in various foreign countries. This interpretation of the mining laws of the Irish Free State has been prepared from the best available material in Washington and is released subject to amplification and correction, if necessary, by American foreign-service officials. INTRODUCTION This paper is based upon the mines and minerals act, 1931, enacted by the Legislature (Oireachtas) of the Irish Free State (Saorstát Eireann), December 22, 1931, the lull title of which is "An act to establish a board to perform functions in relation to mines and minerals, to authorize the making of lenses of mines and minerals belonging to or vested in Saorstát Eireann, to name provider for facilitating the working of other mines and minerals and, for imposing restrictions on the working of minerals required for the support of buildings and works, to amend the law with respect to mines, and for other purposes incidental to the matters aforesaid.'

Jan 1, 1933

By L. S. Harner

This paper which describes the milling practice at the Golden Cycle mill is one of a series of similar papers being prepared by the United States Bureau of Mines. The mill of the Golden Cycle Corporation, formerly known as the Golden Cycle Mining and Reduction Co., is located at Colorado Springs, Colorado, and has been operated since 1907. It is now and has been from its inception almost exclusively a custom mill.

Jan 1, 1933

By Oliver Bowles

Limestone is the most widely used of all racks and is essential to a great many industries, including tae building trades, highway construction, metallurgy, agriculture, end many chemical and manufacturing enterprises. It occurs in some form in every State and is produced in thousands of quarries. Production in 1930 exceeded 134,000,000 tons. It has more numerous and more diversified uses than any other rock. This paper is designed to furnish general information on the various branches of limestone quarrying and their economic importance. Brief reference is made to dimension stone, and a more complete discussion follows of the uses, requisite qualities, quarry methods, grid processes of preparation of crushed and broken limestone. Footnote references serve to guide the reader to more detailed information.

Jan 1, 1933

Jan 1, 1933

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 3/16-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933

By Irwin Roman

NUMEROUS results and formulas have been published for analyzing seismic records, but most of them apply only to large-scale phenomena such as are encountered in studying earthquakes. In a few cases,1 formulas have been published for some of the simpler structures. In the present paper, an attempt will be made to analyze several types of struc-tures without using methods more advanced than those of a first course in calculus. In, tracing a disturbance through a medium, it is almost always possible to base the analysis on Fermat's Principle of Extreme Time, which states that waves of displacement travel between points in such a manner as to make the time of travel an extremum with respect to all neighboring paths. In the simpler cases, comprising most of those used in optics or geophysical prospecting, this time is a minimum and the principle is often referred to as the Principle of Least Time. Within a homogeneous medium, having a uniform speed of transmission of the disturbance in all directions and throughout the medium, the paths are straight and are refracted at the interfaces in accordance with the Snell law of refraction, which states that the ratio of the sine of the angle, made by the ray with the normal to the interface, to the speed of trans-mission is the same on both sides of the interface. Thus, in any medium composed of homogeneous sections, this same ratio has a constant value at all points. In particular, if all interfaces are horizontal, it is apparent that the angles of incidence are the angles made by the ray with the vertical direction. Furthermore, the incident ray, the refracted ray and the normal to the interface are all in the same plane at each refraction;

Jan 1, 1933

By G. S. Rice

The Experimental Mine of the United States Bureau of Mines is a unique coal mine that serves as a large-scale testing laboratory. It is used primarily for testing the explosibility of coal-dust and gases but is also the workshop for many other kinds of research work of which the chief object is to increase safety in mining. The mine is situated in Allegheny County, Pa., about 13 miles southwest of Pittsburgh among the high hills of the west bank of the Monongahela River, at the northeastern edge of the gas-coal district of the Pittsburgh coal bed which extends south through the Connellsville coking-coal district into West Virginia. The Pittsburgh bed, of the Upper Carboniferous age, is one of the most extensive continuous coal beds in the United States, if not in the world. Throughout large areas it shows remarkable uniformity of thickness, levelness, and character of coal, which is a coking coal of high-grade bituminous rank. Its thickness in the northern part is 5 to 5 ½ feet and in the central and southern part is 7 to 9 feet.

Jan 1, 1933

By J. Mackintosh Bell

External trade strongly influences the well being of all nations. In the modern economic mechanism, no country is so well endowed that it has not to import commodities from others and to export its products in turn to make good its deficiencies, to rectify or improve its financial structure. From the standpoint of international commerce, Canada is strategically well placed. On the south she is bounded by the richest country in the world. On the east she faces the Atlantic, on the west the Pacific. On both coasts there are fine harbours to which lead great lines of railway that span the continent. Canada is now fifth among the exporting nations of the world. For disposal abroad, she has enormous quantities of primary commodities and substantial amounts of manufactured goods as well. But she is far from being self-sustaining. She is unusually dependent on foreign trade, not only because of the commodities she has to sell but because of the lack of many essential articles she does not or cannot produce. To Canada, external commerce is vastly more important than internal trade. The wealth of nations is decided by their ability to produce more than they need, to sell more than they buy, and to build up favourable balances resulting from trade or services. With few countries, however, are returns perennially satisfactory. Fruitful periods are followed by leaner years. In times of prosperity foreign credits are increased, monetary systems strengthened, reserves accumulated to withstand recurring days of strain. Today, the foundations of financial systems are being re-examined, "dogmas hitherto accepted as canonical are being questioned" . It is not only in Europe and America that men search for illumination in problems arising from monetary restrictions.

Jan 1, 1933

By W. J. Asselstine

Introduction This paper is prepared from data gathered for a similar paper to be submitted to the United States Bureau of Mines, for publication as one of their information circulars. It covers the history and development of the present milling practice at Premier. The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by D. L. Pitt, Manager of the Premier Gold Mining Company, Limited; also their indebtedness to various members of the Engineering Staff and of the Accounting Department who have assisted materially in gathering the data used. Location The Premier mine and mill are situated in northern British Columbia, approximately fifteen miles north of the head of Portland canal, in the Salmon River section, about half a mile east of the Alaska-British Columbia boundary line where it crosses die Salmon river. The mill is located on a rather steep hillside on the horizon of the main haulage level of the mine, and is within a hundred feet of the mouth of the tunnel. Both the mine and mill are connected with tidewater at Stewart, B.C., by an aerial tramway (1) eleven and one-half miles in length, which delivers both ore and concentrate to the bunkers at the dock for shipment to the smelters. All mine and mill supplies are transported from Stewart dock to Premier over this tramway, except heavy machinery. Heavy pieces have to be hauled either by truck in summer or sleighs in winter over a good road which runs from Stewart dock to Premier.

Jan 1, 1933