Search Documents

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By G. C. McLachlan

Two papers dealing with Noranda's milling operations have already been presented. The first1 of these covered the initial metallurgical problems connected with the treatment of the ore, while the second2 described the development of the mill from a 500-ton unit in 1928 to one with a daily capacity of 3000 tons less than six years later. At the time the second paper was written the equipment whirh had been installed to bring the mill capacity up to 3000 tons was being tuned into production and for this reason, though each step had previously been tested by a large-scale pilot operation, it was thought advisable to withhold metallurgical data until any starting-up difficulties had been overcome and anticipated requirements fulfilled. These requirements called for an improvement in gold recovery without any lowering of the previous ratio of concentration, and the pages that follow deal with the methods by which this result was obtained. An idea of the character of Noranda concentrating ore will be gained from an inspection of the following mineralogical analysis of the ore treated by the mill during 1933: MineRal Content Mineral ConteNt Chalcopyrite, per cent..... 6.8 Silica and silicates, per cent............ 18.3 Pyrite, per cent........... 22.1 Gold, native and as telluride, oz. per ton 0.15 Pyrrhotite, per cent....... 51.5 Silver, probably as argentite, oz. per tou 0.35 Magnetite, per cent....... 0.5 Thesr figures, which are typical, show that over 73 per cent of the ore treated consists of pyrite and pyrrhotite. Determirnation of the proportion of unrecovered gold associated with each of these minerals was therefore of primary importance in developing a suitable method for improving gold recovery. As pyrrhotite is magnetic, this information was obtained by making magnetic sorting tests on samples of the mill tailing and screening the material thus segregated. This showed that the magnebtic material finer

Jan 1, 1935

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By H. A. Doerner

"During the year which has passed since the last progress report on reduction of zinc by natural gas,3 the laboratory experiments on this investigation have been completed. In this concluding report, the whole subject will be reviewed and additional data presented.Chemical ReactionsIn a thermodynamic study of zinc smelting, Maier 4 discussed the use of methane for reducing zinc oxide, and predicted equilibria at various temperatures for the sore important reactions. The study has been extended to include the following list.Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1) at equilibria would be substantially complete at or above 927°C. A subsequent papers described experimental verification of these predictions and gave data on reaction rates under various conditions.It methane is passed through a heated bed of zinc oxide at a low enough rate reactions (1), (3), and (4) reach an equilibrium which can be expressed by reaction (10). The equilibrium concentrations for the products of this reaction in the temperature range 900° to 1100°C. were calculated by applying the thermodynamic constants to the stoichiometric relations. 6 The results of these calculations are listed in table 1 and shown graphically in figures 1, A and B. These data have major importance, and experimental work has shown that they are subtantially correct."

Dec 1, 1934

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By Gustav Wade

"INTRODUCTION Analyses of samples of crude oil from several Texas oil fields have been published from time to time in Bureau of Mines reports, some of which are out of print, but many other analyses of Texas crude oils have not been published. The purpose of this paper is to make available in condensed tabular form under one cover all analyses of the Texas crude oils that have been examined by the Bureau of Mines.DIVISION OF TABLEThe table of analyses is divided into six parts in accordance with the geographic subdivisions of the State. (See fig. 1.) This grouping of the oils corresponds only in a general way with the principal formations in each area from which oil is being produced. In general, the principal oil-producing formations in the Texas Panhandle and West Texas areas are of Permian age; those of North Texas are of Pennsylvanian and older ages; those of the East Texas Basin and of Central Texas are of Cretaceous age; and those of the Texas Gulf Coast are of Eocene and younger ages.For convenience in presentation the name of the geologic age has been assigned to each group of the table although same of the oils included in the group may be of another age.Group 1 includes oils of Permian age produced in the Texas Panhandle area, which comprises the following counties: Dallam, Sherman, Hansford, Ochiltree, Lipscomb, Hartley, Moore, Hutchinson, Roberts, Hemphill, Oldham, Potter, Carson, Gray, Wheeler, Deaf Smith, Randall, Armstrong, Donley, Collingsworth, Parmer, Castro, Swisher, Briscoe, Ball, and Childress."

Dec 1, 1934

By Chester L. Arnold, Reinhardt Thiessen, Alexander Lowy

"INTRODUCTION Peat is the accumulated mass of plant materials that remain after partial decay under specific conditions. In the swampy peat bogs dead material which falls on the surface immediately is attacked by fungi and aercbic bacteria. Decay under these conditions is rapid, but of relatively short duration, since the constant addition of new material soon forces the older layers below the water level, in this position, without access to oxygen, the plant constituents are attacked mainly by anaerobic bacteria, and decomposition proceeds slowly. The largest part of peat is contributed by the woody tissues of plants, the chief constituents of which are cellulose and lignin, together with a small proportion of hemicelluloses. During the normal process of biological decay celluloses disappear more rapidly than lignin. The result is a complex substance known as humin, from which the humic acids may be extracted.In 1826, Sprengel 5 found that when decayed plant materials were extracted with alinnli and the resulting black liquid acidified with mineral acid a brown gelatinous precipitate was formed. To this product, which was a brown amorphous powder when dry, he gave the name ""humic acid'. Since that time, chemists have used the name rather loosely to designate products which have been isolated by very diverse means from soils, decayed woods, peat, lignite, and coal. An excellent review of the early work on humic acids was published by Baumann 6 in 1909. This publication aroused the interest of Oden, who then investigated the humic acids. An account of Oden’s work, as a good survey of the literature, is contained in his monograph “Die Huminsauren”. 7"

Nov 1, 1934

By W. W. Adams

"Although rock-dust is an effective and generally recognized preventive of wide-spread explosions in bituminous-coal mines and although in explosions many lives have been saved by its use that almost certainly would have been lost otherwise, yet more than two thirds of the yearly production of bituminous coal from underground mines in the United States is still being obtained from mines that do not use rock-dust, and more than two thirds of all men that work underground in bituminous mines are employed in nonrock-dusted mines. These facts are revealed by a statistical survey of all mines in the United States that were in operation during 1930, 1931, and 1932. The survey was conducted by the Demographical Division of the Health and Safety Branch of the United States Bureau of Mines and was based upon reports from operating companies received in connection with the Bureau's annual statistical surveys of accidents in the mining industry.In 1932, the latest year for which complete figures are available, rock-dust was used, to some extent at least, in 393 bituminous-coal mines whose total production of coal during the year was 83,632,327 tons, or 30.6 percent of the entire output of bituminous coal from all mines in the United States not including opencut mines. The number of men employed underground at mines that used rock-dust was 25.7 percent of the total number employed underground at all bituminous mines, and the number of man-hours worked at these mines was 27.1 percent of the total number of man-hours worked underground at all bituminous mines during the year."

Nov 1, 1934

By V. E. Erwin, W. W. Adams, E. V. Walters

"Increased production of explosives in the United States in 1933 compared with 1932 is shown by statistics compiled by the Demographical Division, Health and Safety Branch, United States Bureau of Mines. The figures relate only to explosives used for industries purposes, such as mining, quarrying, and road building, and do not cover nonindustrial explosives, such as ammunition or fireworks. Industrial explosives include black blasting powder, permissible explosives, 5 and high explosives other than permissibles figures in the tables of this report were compiled from reports covering sales by the individual companies manufacture of explosives in the United States in 1933. Because of the close agreement among the several series of figures, the quantity of explosives sold is considered as reflecting production and consumption, and the three terms ""sales"", ""production"", and ""consumption"" are used interchangeably in the discussion unless otherwise stated.Of the principal industries that use high construction operations accounted for the largest percentage of increase in consumption during 1933; metal mining and quarrying also used more of this class of explosives than in the previous year. Coal mining is the chief consumer of permissible explosives; the figures for 1933 showed that bituminous-coal mining used a larger quantity than in 1932, and that anthracite mines also showed a small increase. Although a net increase of less than 1 percent in consumption was reported for black blasting powder, large increases in use of this class of explosives were reported for metal mining, miscellaneous types of work, and bituminous-coal mining. (See table 1.)"

Nov 1, 1934

By A. U. Miller

Since coal -mining records have been kept , reports of all mining States show that each year the lives of many workers have been sacrificed in the production of coal , and Illinois has contributed its share , Illinois reports for the 50 years 1882 to 1932 , inclusive , show that 6,673 men were killed -- 6,121 underground , 340 in the shaft , and 212 on the surface . Of the fatalities underground , 3,116 were caused by falls of roof or sides , 1,111 by haulage , 630 by explosives , 577 by gas explosions , 139 by electricity, and 548 by other causes ; 166 of the shaft fatalities were caused by falling down the shaft , 143 by the cage , and 31 by other causes ; 108 of the surface fatalities were caused by railroad cars , 46 by machinery , and 58 by other causes . Most of those engaged in mining are still of the opinion that it is an extremely hazardous occupation and that it is practically impossible to operate without accidents ; however , students of safety in mining now believe that with the proper attention to accident prevention mining may be conducted with little , if any , greater accident rate than that of other supposedly hazardous industries . There is no mystery connected with accidents in mining ; reports show that the majority are due to two main causes , falls of roof and sides and haulage . Mining companies in Illinois , as well as in other States , have proved in the past few years that the hazards of mining , like those of other industries , can be controlled to a large extent and the mines operated with few if any accidents , provided a great enough effort is made by employer and worker . Although the past accident rate of Illinois may compare favorably with that of other mining States it is higher than it should be ; the fact that 6,673 men (an average of 133.46 per year) were killed in and around the mines of the State between 1882- and 1932 indicates that accident prevention should receive more consideration in the future than in the past .

Nov 1, 1934

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION The investigation of the general hazards of combustible gases and vapors in manholes owned by the Edison Electric Illuminating Co. and the study of methods for eliminating these hazards, conducted by the Bureau of Mines, the Edison Electric Illuminating Co. of Boston, and the Boston Consolidated Gas Co. since 1929, was continued during 1933.From May and through December 1933 these tests were supplemented by a study of the manholes of the New England Telephone & Telegraph Co. The test crew was under the direct supervision of John Campbell, superintendent of the Special Service Department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Boston Consol¬idated Gas Co.The procedure of sampling manhole atmospheres and of shipping the samples to Pittsburgh was the same as that used heretofore. In previous reports the relative explosibility of the samples was calculated by adding the percentages of the illuminants, hydrogen, carbon monoxide, methane, and ethane, dividing the total by 6.5, and multiplying by 100. Experience has shown that the factor 6.0 is more nearly correct; therefore, this has been used in calculating the relative explosibility of all the samples listed in appendix A and B of this report. If gasoline vapor is present a smaller factor must be used.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of W. C. Bayliss, president of the Edison Electric Illuminating Co. of Boston; W. C. Beckjord, vice president and general manager of the Boston Consolidated Gas Co., and A. C. Fieldner, chief engineer, Experiment Stations Division, United States Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department of the Edison Electric Illuminating Co., cooperated heartily in furnishing both men and information for the work."

Oct 1, 1934

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934

By C. W. Owings, J. J. Forbes

"Although coal-mine explosions rank third among causes of underground fatalities, they receive more wide-spread attention than any other accidents in mines because frequently many persons lose their lives in a single disaster. Each bituminous coal-mine explosion endangers the lives of approximately 100 persons--the average number employed underground in a commercial mine. A critical analysis of coal-mine explosions in a restricted district gives a cross-section of relative existing explosion hazards, of common causes of ignitions of gas and dust, and of effective prevention measures. The Safety Division of the United States Bureau of Mines is collecting data on coal-mine explosions in the various States, and this circular is one of a series analyzing the causes and recommending methods for thy prevention of similar occurrences,The data on this circular are based on records of the United States Bureau of Mines and the West Virginia Department of Mines. Unfortunately practically all of the early records were destroyed by fire in the State House at Charleston, W. Va.; the remaining records were made available to the authors by N. P. Rhinehart, chief of the Department of Mines, and his cooperation is gratefully acknowledged.The earliest available reference to coal in West Virginia is that made by John Peter Lally who in 1742 found ""a great plenty of coals"" near a river later called Coal River. In 1809, Nicholas Roosevelt found coal along the Ohio River and used it on the New Orleans, said to have been the first steamboat west of the Allegheny Mountains. In 1810, Conrad Cotts opened a mine near Wheeling and sold coal for domestic purpose in 1812, a mine was opened on the Ohio River opposite Mason City and produced 1,200 bushels of coal that year. In 1840 the total West Virginia coal production was 298,691 tons; in 1863, the production had increased to 444,468 tons, and in 1883, to 2,335,833 tons. During this period apparently most of the coal was extracted from coal outcropping on the hillsides; little danger of gas ignition existed at that time, but explosions from blown-out shots occurred frequently. On February 22, 1383 the West Virginia legislature enacted legislation providing for a mine inspector to inspect the mines of that State, to prevent mine accidents, and to insure properly ventilated mines.In a special report to the Governor on December 31, 1884 the Inspector of Mines reported:We have 5 shafts, in 4 of which there is more or less gas; and in 1 of our drift mines there was an explosion on the 27th day of March 1880, whereby 2 men were killed and a boy badly burned.Table 1 lists 287 explosions in West Virginia coal mines. Several early explosions were listed in the annual reports of the West Virginia Department of Mines as ""blown-out shots"" or ""powder explosions"". The injuries usually were described; explosives accidents have been eliminated from these and other available data, and only those in which dust or gas were involved have been included in this paper as explosions."

Sep 1, 1934

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Arthur L. Crawford, R. E. Head, Glen Burgener, F. E. Thackwell

"INTRODUCTION This report embodies the results of a detailed statistical microscopic examination of the ore and the mill products of the Silver King Coalition Mines Co., Park City, Utah.The study was conducted under the joint auspices of the United States Bureau of mines is cooperation with the University of Utah at Salt Lake City, Utah. The work was done in the cooperative Microscopic Service Laboratory, which was equipped by contributions from the following companies: Utah Copper Co., International Smelting & Refining Co., American Smelting & Refining Co., United States Smelting, Refining & Mining Co., Tintic Standard Mining Co., Silver King Coalition Mines Co., and Park Utah Consolidated Mines Co. The salaries and the other costs involved in operation of the laboratory were met by contributions from certain supporting companies. In addition to the regular personnel of the laboratory the Bureau of Mines contributed the part-time services of a microscopist-consultant to direct and assist with the technical work.ACKNOWLEDGEMENTSThe authors acknowledge the courtesies extended by the Silver King Coalition Mines Co., through its general manager, M. J. Dailey, in furnishing the various ores and products on which the study was made, together with general information concerning the problems encountered or recognized in connection with the milling of the Silver King ore."

Jun 1, 1934