Search Documents

By Robert K. Guthrie, James W. Amyx, D. B. Taliaferro

"INTRODUCTION Secondary recovery of oil by water-flooding is practiced more extensively in North Texas than in any other section of the State, and the progress and experience of the operations in that area are of continuing interest to all branches of the oil industry. The first Bureau of Mines report on water flooding in North Texas 7/ chronicled the activities from December 7, 193f', when the Railroad Commission of Texas granted The Texas Co. the first permit to inject water into an oil-bearing sand, through 1944. This second report has been prepared as a supplement to Report of Investigations 3906 to show the progress and expansion of water-flooding. The format of this report is almost identical with what of report of Investigations 3906, except for a few miner changes. For the sake of brevity, certain basic information contained on the first report has not been repealed, and the reader is urged to consider the two reports as corporation writings.The North Texas area, as encompassed by the two reports, corresponds Railroad Commission of Texas Districts 7P and 9. Oil-development operations in the two districts, since oil was discovered in 1904, have resulted in the recovery of approximately 1,400,000,000 barrels of oil from a proved area that has been estimated to exceed 413,000 acres. During October barrels of oil was produces by primary and secondary-recovery methods from 1,746 flowing wells and 25,211 pumping wells, a daily average 6.6 barrels per well. Of this total volume of oil recovered in October 1947, 47,965 barrels (0.87 percent) was recovered from leases on which water-flooding operations were in progresses."

Feb 1, 1948

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

The standard method of employing preliminary air-drying to determine the moisture in coal has been criticized with respect to the loss of heating value from excessive air-drying. By this method, the coal is air-dried at approximately 10-15° above room temperature with the loss in weight being less than 0.1 percent per hour, and then the residual moisture at 105°C is determined. The total moisture is calculated from these two values.

Feb 1, 1948

By W. H. Ode, W. A. Selvig

Briefly, this swelling test consists in heating 1 gram of pulverized coal in a silica crucible over a gas flame under prescribed conditions to form a coke button which is compared in size and shape with a series of standard profiles numbered 1 to 9. These profiles are intended to cover the size and shape of buttons obtained from coals covering a wide range in plastic properties. The number of the standard profile with which the maximum cross-sectional area of the button most nearly corresponds is recorded as the swelling index. Although the swelling test showed poor relationships with the various tests that were used for measuring expansion or contraction of coal during carbonization, it gave indications of having value in measuring free-swelling and coking properties of coals when burned on fuel tests. An opportunity to investigate this occurred when an engineering company reported pronounced differences in burning characteristics on grates of various shipments of Pocahontas coal. Some of these coals gave trouble by swelling excessively and clogging the grate. Samples were obtained, and it was found that the troublesome coals gave radically higher free-swelling numbers than did the coals that performed satisfactorily. Also, it was found that the free-swelling index test gave better differentiation between coals than could be obtained from the coke buttons from the standard volatile-matter test or iron agglutination-value results. The results of the free-swelling test were confirmed by the Subcommittee on Plasticity and Swelling, Coal, a special group of the Subcommittee, under the chairmanship of R.A. Shuman, worked along with the test method. Estberg, Limacher, and Shuman of the Battelle Memorial Institute investigated the various factors affecting the test and found that the swelling index was a good indication of the suitability of coal for performance on residential-type stokers from the swelling characteristics of the coal. Data were presented that also showed that the index was helpful in the selection of coal for industrial underfeed stokers.

Feb 1, 1948

By Alfred L. Ransome

The consumption of slab zinc in the United States increased sevenfold in less than a half century since 1900. Therein is reflected the innate characteristics of this versatile and nearly indispensable nonferrous metal whose use has grown at more than twice the rate of industrial production. The total metal consumption was substantially stimulated during the two World War periods, which were likewise marked by notable changes in use pattern accompanied by shifts in geographic distribution. This information circular summarizes basic data collected for many years by the Bureau of Mines, but in particular presents for the 1940-45 period details derived from the comprehensive slab zinc consumption survey inaugurated in 1940. The total consumption of slab zinc has been broken down into four major categories galvanizing, brass products, rolled zinc, and zinc-base alloys -- with minor applications grouped under a fifth heading, other uses. Ex- cept for the inclusion of zinc-base alloys with other uses before 1926, the above-named segregation has been shown for the entire period 1900-45. 11- though a substantial tonnage was taken by all groups in all years, there were large shifts in the use pattern in both World War periods. In both, the Allied Powers depended heavily on the United States for zinc-bearing products, especially those required by war industrius. The departures from usual uses were, however, much more marked during the second than in the first period, mainly because the United States could not have met the tro- mendously expanded war-materiel demands had the greater slab zinc needs of a period of high industrial activity been supplied. The geography of consumption is known in detail only for 1940-45. Even in that short period, substantial shifts are observable, largely the reaction from conversion to war production in 1940-41 and reconversion to peacetime consumption in 1945. However, there is so evidence of other shifts in consumption centers that appear to reflect longer-term develop- ments.

Feb 1, 1948

By Robert J. Hundhausen

This information circular is one of a series of Bureau of Mines reports dealing with mining and milling methods and costs . It describes the operations at the Little Pittsburg mine in the Pine Creek area of the Coeur d'Alene mining region near Kellogg , Idaho . The mine and mill have been operated successfully from 1942 to the present .

Feb 1, 1948

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By D. W. Butner

The blast -hole method for drilling and breaking ground is not new to the mining industry . For several years it has been used rather extensively in Canada , particularly in the gold mines , where it was first developed and where the major advances in the technique as applied to present - day mining problems have been made . At present , 40 mines in Canada and the United States are using the method in one form or another , and from all indications its use will increase in the future . In two California mines , blast -hole diamond drilling is now used for a part of or for all stoping operations , and in one of these it is used to some extent in development work . At the Mountain Copper Co.'s Hornet mine in Shasta County, about 50 percent of the pyritic sulfide ore produced is mined by the blast - hole method , and the U. S. Vanadium Corp. mines 80 percent of the ore produced at its Pine Creek tungsten mine in Inyo County by this method . At Pine Creek , long -hole drilling and blasting is used for mining pillars also , and in pre - stoping development . The blast -hole diamond - drilling method is not applicable to all types of ore bodies . A third property in California , the El Dorado Limestone Company , El Dorado County, tried the method for several months in 1943 and 1944 , but , owing to certain factors that greatly increased mining cost , the company soon returned to conventional mining methods .

Feb 1, 1948

CONTENTSIntroduction.Ore Bodies.Variations in Ore Dressing Practices.Stage I .Gravity Concentration for the production of a Lead Concentrate. 1909-1918.Stage Il Gravity plus Flotation Treatment for the production of a Lead Concentrate and a Zinc Concentrate. 1918-1929.Stage III All Flotation Treatment for the production of a Lead C~mcentrate and a Zinc Concentrate. 1930-1939General Summary - Stages I, II, III.Stage IV Gravity plus Flotation Treatment for the Production of a Lead Concentrate and a Zinc Concentrate. 1939-1947.1. General.2. Notes on Ore Dressing Practice.A. Gravity Section - Re~oval of Free Galena.B. Secondary Ball Mill Grinding Section. .a. Mineral Association.b. Composite particle problem.c. Degree of grinding required.d. Free Gangue Minerals in Table Tailing.

Jan 1, 1948

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By F. A. Rutledge

The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively prospected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941. The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program. The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.

Jan 1, 1948

By S. J. Pearce

There are a number of methods for determining relatively small quantities of sulfur dioxide in air. However, those methods require fairly elaborate apparatus and laboratory facilities. Frequently in industrial hygiene surveys it is desirable to have a simple arrangement to obtain "on the spot" determinations. This has been accomplished for concentrations of sulfur dioxide of hygienic significance by using the midget impinger and decolorizing a starch-iodine solution.

Jan 1, 1948

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By T. J. Ballard

The Conrad Hill mine vas first opened as a gold mine about 182 and has been operated at various times since then. The Bureau of Mines, as part of the strategic minerals program, mapped and sampled the accessible mine workings. The work failed to reveal appreciable copper values or evidence of additional ore deposits.

Jan 1, 1948

Jan 1, 1948