Search Documents

By Benjamin Gi ldersleeve

Uniquely colored, thin-bedded quartzite is quarried between Crossville and Crab Orchard in Cumberland County, Tenn. It is produced in all sizes up to the limits of transportation from beds usually ranging in thickness from less than 1/2 in. to 6 in. The stone is very resistant to wear and weathering and is marketed throughout the country for many different purposes in exterior and interior construction. The annual production exceeds 36,000 tons, valued at nearly $1,000,000.

Jan 1, 1950

By E. C. Wright

FOR many years the cost of making pig iron and steel in the Birmingham district has been about the lowest in the United States. The close proximity of the important raw materials such as coal, iron ore, limestone, and the large available scrap supply made it possible to assemble all of the important ingredients necessary for steel- making with only nominal costs for transportation. Both iron ore and coal were being mined in this district at one time for about $1 per ton from underground operations. At that time mining wages were low everywhere and the labor rate in the South was considerably below that of other mining districts. This situation persisted until the emergence of labor unions as an economic and political force, emigation of southern labor to northern plants, and continued growth of industry in the South in the years following the depression of 1932. Since that time union organizing of miners and steel workers throughout the nation has increased labor costs in mining and steelmaking. This influence has been felt particularly in underground mining operations since the proportion of labor cost to total cost is still high. The previous advantage in basic labor rate in the South has been almost entirely eliminated by the equalization of labor rates in basic industries by national unions. Since 1945 these influences have been especially noticeable in increasing the cost of mining coal and iron ore in the South. The northern steel districts are still being largely supplied with iron ore from the Minnesota open-pit mines and the cost of this ore has not increased nearly as much as the cost of ore obtained from underground mines in Birmingham. A similar situation exists in coal mining; the thinner seams in Alabama are not so amenable to mechanization as the northern mines and, as a result, the output per man-day in southern mines is only about three tons of coal as compared to five or six tons per man-day in the large captive mines of West Vir-

Jan 1, 1950

By R. E. Zimmerman

Wide attention is being placed upon various methods for cleaning the fine sizes of bituminous coals. The author describes and analyzes the results achieved on wet concentrating .tables of modern design on unclassified feeds of - 1/2 in. particle sizes, including tests on high-sulphur coals.

Jan 1, 1950

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By Kefton H. Teague

This paper deals with the practical application of the Dutch State Mines cyclone separator for fine-coal cleaning. The more important operating variables are discussed, and results of a number of continuous-scale tests on various fine coals with a 6-in. cyclone separator are given. Descriptions of the Cyanamid Pilot Plant and the 50 tph Cyclone Separator Plant at the Emma Washery in Holland are included.

Jan 1, 1950

By AIME

Burton J. Westman-Besides decreasing the diamond size, there appear to be two other approaches open to overcome excessive diamond loss and, more particularly, the rapid diamond polish that took place in this quartz-feldspar rock. First, however, a short discussion of the diamond characteristics should be made in order to discuss the situation more clearly. The West African diamonds which we can assume were used. for this drilling have two disadvantages when drilling hard, exceptionally fine-grained rocks. These are rapid polishing and, if .the bit isn't "drilled in" carefully, a tendency to damage, resulting in excessive diamond loss. The normal wear resistance of any diamond is inversely proportional to the compressive strength of the diamond, therefore only the highest grade, of diamonds free from insipient fractures should be employed. Using upwards of 90 diamonds per carat instead of the20 to 30 per carat not only decreases the total projected area of the cutting points but increases the stress per point which, in turn, causes greater depth of penetration into the rock. Considering this depth of penetration, therefore, suggests an approach other than increasing the, number of diamonds per carat and that is to decrease the actual number of diamond points (also the carat weight per bit) so that the penetrating force on an individual diamond is increased. This penetration increases the chipping or rock shearing action.

Jan 1, 1950

By Richard Hamburger

Calculating machines permit the use of the more rapid cotangent and semigraphic solutions of plane triangulation. The results of these methods are as accurate as those of other methods. Simple adjustment of the net, and ease of calculation encourage more complete field work. Errors in field work or in computation are easily localized.

Jan 1, 1950

By J. P. Smith

Permian salt measures carry extensive lenses of soluble potash salts in north central Germany. Potash deposits of Oligocene age are found in the Upper Rhine Graben of Alsace (France), and in the Catalonian Basin of Spain. These deposits are found in a wide range of structural settings. Reserves are large, and the production of potash salts is an important phase in the economy of each of these countries.

Jan 1, 1950

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 1, 1950

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950

By Homer W. Riley

ANTHRACITE SMALL power-driven, toothed, cast-iron rolls were used first to break anthracite in 1844. Prior to that time, men with hammers, who stood on perforated cast-iron plates, broke the large lumps into commercial sizes. In order to convert run-of-mine into the various sizes required by the anthracite industry, about 20 million tons must be broken, annually, into smaller sizes. This phase of anthracite preparation is of major importance, because the degradation accompanying reduction in coal sizes should be kept at a minimum. The exclusive use of toothed rolls for that purpose indicates that comminution by rolls is the best solution of the problem. Many improvements have been made in tooth design, but the most important was a reduction of the peripheral speed of the rolls from 1000 to 300 ft. per minute. The higher speed was based upon and approximated the velocity of a falling piece of coal when it entered the rolls, Exhaustive roll tests at the slower speed showed that the same size reduction could be affected with less degradation. The adoption, therefore, of slow-speed, compound geared rolls, especially for breaking the larger sizes, became quite general after 1912. A high-speed roll is shown in Fig. 1 and a slow-speed roll in Fig. 2. Anthracite Crushing Problems.-Crushing anthracite presents the problem of selecting a series of rolls that will produce the greatest percentage of the prepared sizes of nut and over. The size distributions to be expected are shown in Table 1. Coal breaking and crushing practices in anthracite breakers involve the use of equipment for comminuting the following classes of material: 1. Run-of-mine-plus 6 ½ -in. coal. 2. Sized coal-steamboat, broken, egg, stove, nut, and pea. 3. Flat coal--coal that is flat and hence not suitable for the market. 4. Bone--a piece of laminated coal and slate, crushed for the purpose of reclaiming the coal. 5. Breaker refuse, reduced to a size suitable for flushing into a mine for back-filling purposes.

Jan 1, 1950

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

By Almon F. Robertson

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are being made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power developments within the Missouri River Basin. This report has been designed to permit public distribution of the factual data obtained . Virtually all known metallic -mineral occurrences and some nonmetallic mineral deposits within Fergus County were investigated in 1948. The investigations cannot be considered complete , however , because some long inactive mines or prospects may have been missed . Most of the old mine and prospect openings now are caved ; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from available Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

D EC. 20-The spirit of Christmas and good will toward men has managed a few brief appearances on the front pages, welcome relief from man's usual ill-will toward man. A couple politicos did their best to brighten the scene by well-publicized romances. There was a general exodus to Florida to patch up nervous systems, and even the UNO quieted down as Mr. Vyshinsky departed for home via Eastern Germany. Before going he opened up a preliminary bombardment for the worldwide "communist peace offensive," and it is now the duty of the 600 million (according to the Cominform) ideological converts to press home the attack. In Washington, Mr. Lilienthal resigned as Chairman of the Atomic Energy Commission and demonstrated again the difficulty of government to retain the services of capable men. The President has yet to appoint another victim- possibly someone nicely noncontroversial and timid. So might the critics be appeased, but it would bode ill for the rapid exploitation of peaceful uses of atomic energy, the relaxation of excessive secrecy, wider sharing of developmental work with friendly nations and possible revision of the Acheson-Lilienthal proposals for inter- national control of the atomic bomb.

Jan 1, 1950

By S. H. Ash, J. J. Forbes

Probably the newest thing in mining safety, or safety for mines, is the apparent dissatisfaction on the part of the mineral industries, as represented by both management and labor, and the general public of the Nation, with the safety record of the mining industry. This is reflected by published comments and papers in the technical press;l-9 in labor periodicals,10,11 in popular journals and periodicals,l2, 13 and in the daily press; also by discussions of the Safety Committees sponsored by the National Safety Council,9, 14-15 the American Mining Congress,l.l6 the American Institute of Mining and Metallurgical Engineers,2,4 the Mine Inspectors' Institute of Amerthe Coal Mining Institute of America,5 19 the American Standards Association, and others.20.21 Mining safety is a joint problem of management and the individual workman. Safety is not attained and will not be attained solely by laws, decrees, and commands because, if it could be done in this manner, acceptable mining safety would have been achieved long ago by the individual states in our Nation and by the nations abroad. The best safety performance is found at plants where management provides a safe environment for the workers; where supervision is efficient and super- visors, others concerned with promoting safety, and the individual worker know through training, experience, and personal contact the safe and unsafe practices of their field; and where the trained individual worker has become safety-minded by experience, quiet influence, unconscious suggestion, and personal guidance. Despite what may be said to the contrary, progress has been and is being made in mining safety. This is shown in Fig 1 to 4. It is beyond the scope of this paper to give possible reasons for the valleys and peaks in the fatal-injury rates. Some recent factors that appear to be contributing to the improvement in these rates are briefly discussed. Aside from mining equipment, "what's new in mining safety" for some mines has been in effect or was tried by others long ago. A safety pro- gram is a living thing; as such, it must be vitalized and continuously fed with enthusiasm, constructive action, and improvements. Because safety is concerned with human conduct, it is necessary to practice safety at all times; if not, it is soon forgotten, and accidents occur. Mining-safety Records The large employment and production concerned with anthracite contribute much to the mining-safety records of the mineral industry. Approximately 81,000 persons are. employed in this industry having mines concentrated in an area of 480 square miles in northeastern Pennsylvania. Because of the achievement of the anthracite industry in safety during 1948, the other branches of the mineral industry can profit by a study of what has been done to achieve that record. Where one mineral is produced by other large groups having methods of mining that are similar in many respects to the anthracite-mining methods, an achievement in such a large industry is important. Salient factors concerned with safetye in the anthracite industry are: no radical change has occurred in the mining-safety regulations pertaining to anthracite mines. Because anthracite mining is a branch of the coal-mining industry,

Jan 1, 1950

By C. M. Brinckerhoff

Safety work in mining at the Andes Copper Mining Company, Potrerillos, Chile, is divided into three parts: (1) accident prevention, (2) fire prevention and protection, and (3) silicosis prevention and control. In the company's operations a steady campaign has been waged to reduce accidents and silicosis, and to prevent fires. In the following pages the safety record for the past twelve years will be examined and the methods explained by which the accident rate was reduced. Table 1 contains yearly data pertaining to the scale of the mining operations and the accident record. Block caving is used for all ore production and the tonnage mined has averaged 30,000 short tons per day for the past seven years. Table 2 classifies 44 fatal accidents which have occurred since 1935. The leading causes of accidental death are transportation of ore and use of explosives, followed in order by persons falling, falls of ground, and by asphyxiation. In the case of serious accidents, however, the greatest cause is falls of ground, followed, in turn, by ore transportation, persons falling, explosives, and asphyxiation. Accident Prevention The improvement of the safety record was obtained by a combination of many factors. In surveying the results at Andes for the past twelve years, it is possible to select some features of the present operation which have contributed to the accident record. The most important of these are: (1) good staff planning, (2) good equipment, (3) an alert safety organization, and (4) education and selection of the workmen. GOOD STAFF PLANNING As a result of good staff planning, the mine has good working conditions, namely, good ventilation, moderate temperatures and humidity, and good lighting. These factors not only reduce accidents but also improve efficiency. In haulage work, accidents have been reduced by having traffic move in a forward direction only. The latter makes possible a one-man train crew. Trains are centrally dispatched from loading drifts which are interconnected by signal lights, so that when a train in a lateral drift is given permission to move into a main line drift, a red light signals in all other lateral drifts in that area. Good track is maintained, and safety niches are required at all switch throws. Since safety niches were provided there have been no fatal or serious accidents at such points. All main line haulage drifts are illuminated by electric lights. Haulage drifts are kept clean. Adequate clearance has been provided between cars and between cars and the sides of the haulage drifts. The 4 1/2 ton Cranby type cars are equipped with roller bearings, and the 10 ton loconlotives with trolley shoes instead of wheels. These two features are responsible for improved ore haulage conditions and contribute to greater efficiency and safety.

Jan 1, 1950

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

By J. J. Forbes

Problems connected with the incidence, effects, determination, and control of dusts are still much before the public, although more information is available to the layman than when Bulletin 400, of which this publication is a revision,5 was issued in 1937. Bulletin 400 attempted to assemble information in convenient form on various phases of the dust problem, largely in the mining and allied industries. This revision includes data that have accumulated since 1937 and some that appeared previous thereto but were not available to the authors at that time. The literature on this subject is so voluminous that no attempt has been made to include all published material or all types of dust diseases, but only to assemble some of the more outstanding data on several aspects of the subject.

Jan 1, 1950

By S. H. Ash

The Pennsylvania anthracite region is composed of four fields, namely, the Northern, Eastern Middle, Western Middle, and Southern. It is in the eastern part of Pennsylvania and is shown on figure 1. The anthracite industry is confronted with a crucial problem of inundation by water impounded in underground pools in many mines and by infiltration of water from streams and pools on the surface (3). The deposits of anthracite in the United States are limited virtually to Pennsylvania, and the difficulties of this industry have been commonly considered as a State problem rather than a national one (1, 4, 6, 7). Anthracite was discovered in Pennsylvania in 1762, and the first mining company was formed in 1793. It was not until 1812 that anthracite began to receive recognition in the Philadelphia market as a domestic fuel, and by 1838 the annual production was nearly 1 million net tons. Since anthracite mining began, mine water has become progressively more difficult and costly to handle because of the extraction of anthracite both underground and along the outcrops of the beds, until at the present time mine drainage is a major anthracite-mining problem. Mine water is handled at the anthracite mines as follows: (a) by pumping, (b) by drainage tunnels, (c) by combination of pumping and drainage tunnels, and (d) by water hoists (hoisting water by means of large buckets) (4, 5,6, 7). This paper covers removal of the water from mines by means of pumping plants. Pumping is indispensable in the production of anthracite (5). The cost of pumping mine water has increased progressively since anthracite mining began. Some collieries have been forced to discontinue mining because of the high cost of pumping.

Jan 1, 1950

By N. S. Wagner, R. S. Mason

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Norinally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now heing used as lightweight aggregates in Oregon. The present piche will surely change, perhaps quite radically within even a short space of time. Lightweight Aggregates Used in the Northwest PUMICE Interest in Oregon pumice is not new. Deposits are abundant. Successful development, however, dates only from 1946. During 1948 a total of nine operations was engaged in full or part-time production of aggregate. The postwar building boom and increased public consciousness regarding the value of insulation are the immediate reasons behind the current development. Just how firmly this production of pumice aggregate may be established is something which cannot be foretold at the present time. Much will depend upon how successfully the pumice aggregate construction already installed stands the test of time. Some fine pumice aggregate products have been made and it seems probable that because of its unique properties a certain demand for pumice aggregate will continue in the future. Fire-proof, rodent-proof, decay-resistant properties supplement the lightness in weight and insulation properties of pumice aggregate products in rendering them particularly ideal for many types of construction. In addition there has been fabrication in the form of reinforced fence posts, street markers, and similar products of a specialized-product nature and these are not to be overlooked in terms of future production. Also pertinent to how soundlj pumice aggregate production is established will be possible future competition with other lightweight aggregates. However, this situation will be governed largely by competitive costs of production and marketing. For its present use, which is almost exclusively limited to the manufacturing of building blocks, the market for Oregon pumice aggregate has been extended from the mining area around Rend and Chemult to points as far distant as San Francisco and Seattle. Naturally enough the bulk of the production goes to the Portland and eastern Oregon consumers. Shipments are made by both rail and truck. Early in 1947 the State Department of Geology and Mineral Industries made a canvass of all pumice producers in the state. The production for 1956 amounted to 26,614 cu yd and was valued at $13,649 at the plants. The United States Bureau of Mines estimates the production for 1947 as 33,240 short tons valued at $111,380. This is roughly 65,000 cu yd. No data are available for the 1948 production but it is understood to exceed that for 1947. The Oregon pumice occurrences originated largely from the eruption of Mount Mazama, the name of the formerly active volcano and the location of Crater Lake. Other lesser volcanoes throughout the area contributed to the present occurrences, however, and it has been estimated by Moore' that the pumice deposits cover an area of some 3500 square miles. This area lies east of Crater Lake between Bend and Klamath Falls and embraces the southern portion of Deschutes County, the northern part of Klamath County, and the northwest corner of Lake County. Thickness of the pumice ranges from thin skims to local thicknesses of as much as 30 to 40 ft. Fragment size also varies greatly. Any attempt to describe the situation by giving screen analyses would be confusing because of the wide variations to be found in all area of this size. The picture can best be summed up by stating that places showing great variations in fragment size can be found if a search for extremes is made. For mining purposes in connection with aggregate production, it call be stated that miles and miles of pumice exist in which the fragrnent sizes range from an inch or so downward. The usual color of the pumice is a light gray to off-white. A typical pumice analysis shows a silica content of about 69 pct, alumina 15 pct, and sodium oxide about 5 pct. Potash, lime, and water are the next three most abundant constituents, running just a little over 2 pct each. Iron oxides are fairly constant at 2.75 pct. Titanium, manganese, magnesium, and phosphorus occur in amounts of less than 1 pct. All of the foregoing substances are combined as a glass exhibiting cellular structure. The weight of crushed but otherwise pit-run (undried) pumice runs around 1100 Ib per cu yd according to figures furnished by various producers. The minimum and maximum weights per cubic yard reported are 1050 and 1400 lb, respectively. The 1400 lb per cu yd pumice contrasts with the pumice from most of the other

Jan 1, 1950