Search Documents

By R. L. Smith, J. L. Rutherford

ALTHOUGH considerable effort has been devoted toward the determination of the mechanical properties of pure metals, it is extremely difficult to compare the results of such work. This is because of differences in method and type of test, grain size, heat treatment, and purity of material. There is very little information on the properties of most of the high melting point reactive metals with purities greater than 99.9 pct. Previous evidence concerning the tensile properties of unalloyed metals show that: body-centered-cubic metals are brittle at low temperatures; face-centered-cubic metals remain ductile; some hexagonal metals remain ductile, others become brittle. It may be that traces of impurities decrease the low temperature ductility of the body-centered-cubic lattice. This would suppose that a body-centered-cubic lattice free from impurities would exhibit nearly the same ductility as a face-centered-cubic structure. The present investigation has been an evaluation of the tensile properties of zone refined iron in order to determine whether higher purity material than that previously evaluated behaves differently. Experimental Procedure In this investigation, high purity iron was zone purified using the floating zone method.' The starting stock was obtained from two sources. The first,

Jan 1, 1958

By Milton B. Hall

This report discusses in detail laboratory and pilot-plant tests conducted from January 1951 until January 1955 at the Northwest Electrodevelopment Experiment Station of the Bureau of Mines, Albany, Oreg., on defluorination and recovery of evolved fluorine from phosphate rock. Results of use tests of defluorinated phosphate rock by cooperating agricultural colleges and the United States Department of Agriculture are also included. In 1954 the consumption of fluorspar, the only domestic fluorine-bearing mineral of commercial importance, was approximately 478,000 short tons; 245,000 tons was from domestic mines. The production of marketable phosphate rock in the same period was about 13,800,000 long tons. Of this total amount, approximately 15 percent was produced in the West. From the viewpoint of conservation and utilization of fluorine as a natural resource, it is interesting to note that the total estimated quantity of fluorine in domestically produced phosphate rock is more than double that present in domestically mined fluorspar.

Jan 1, 1958

By Chester S. Conrad

SEVERAL years ago Pittsburgh Consolidation Coal Co. intensified efforts to combat the hazard of mine fires. The program consisted of three parts in the order of likely accomplishment: 1) Purchase and installation of newer and more practical fire fighting equipment. 2) Establishment of trained fire fighting teams at every mine plant. 3) A drive to remove the causes of mine fires. Experimentation with alternating current on section equipment is a major development in this part of the program. Use of alternating current to power mining equipment had been recognized as being most practical from the standpoint of safety. A means to re- place the d-c traction motor is all that has delayed complete section mechanization with a-c power.

Jan 1, 1958

By Gunderson C. T

The use of carbide tipped integral drill steels and detachable bits is discussed in relation to the means of drilling or cutting employed. It is stressed that only by correct use can the full value of these tools be realised.Factors affecting carbide quality, the design of shanking steels and the requirements and techniques of brazing in inserts are considered.It is essential that the brazed jointing between carbide and steel be strong but ductile. The methods used for the manufacture of carbide tipped tools are briefly outlined.INTRODUCTIONIn recent years the application of tungsten carbide to various mining tools in the mining industry, has developed to the stage where it is now regarded as an essential item in the production of coal and metal ores. In fact it is claimed that certain mining operations would not be possible if it were not for the benefits obtainable from the characteristic properties of tungsten carbide. The advantages of this hardmetal have, to some extent, influenced manufacturers to revise design specifiations of some machines, while againsome machines have actually been designed with tungsten carbide as their basic medium for operation.In general the applications fall into the following three categories:(a) Drilling hard rock by percussive means.(b) Drilling soft rock and coal by rotary means.(c) Coal cuttingThis paper is concerned with tungsten carbide tools associated with these three activities in Australia, the effectiveness of their application and significant points in their design and manufacture.

Jan 1, 1958

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By R. M. Wilson

Concentrating plants, in common with other types of industrial plants, cannot operate without lectric power. The elctric distribution system and utilization equipment; therefore, must be carefully considered in all phases of plant design. Two important aspects of proper distribution and usage of electric power are the selection of voltage levels and the methods of system grounding. These are not necessarily the most important design considerations, but are perhaps more controversial than other major points, Modern plants demand increasing amounts of power which, since electric power is the product of voltage and current means higher voltages or currents. Higher voltages require more insulation, higher currents more conductor. The equipment designer?s problem is to obtain in his transformer, cable, switchgear, controller, motor, etc a balance of insulation and conductor to obtain a satisfactory design at lowest cost. To provide the most economical system, both in initial and operating costs requires the system designer to select the proper voltage level. Adequate voltage also permits expansion to meet future requirements, and results in better operation of utilization equipment, Relatively little advancement has been made in recent years in improving conductors; however, great progress has been made in improving insulation. Thus modern plants, in general, now find it more economical to use higher voltages than they did previously. For example plants which only a few years ago would have used 2400 volts as a system voltage often find nowdays that 4160 volts is their proper choice. If the plant requires 10,000 kva br more, then an even higher voltage, such as 13,800 volts, will prove economical. However, for the average concentration plant, with less than 10,000 kva demand, the choice of distribution voltages is between 2400 and 4160 volts, and 480 volts will be used for the low voltage utilization system.

Jan 1, 1958

By Alfred Bodenlos

El presente texto señala los depósitos de plomo, zinc encontrados en la mina Huallpac, Macón, Cerro Plumisa; los cateos del área de la laguna Shagallán, Uchco, cateo del cerro Cieren y la mina Buena Casma y Mangán, pertenecientes a la Cordillera Negra, ubicado en Ancash, Perú.

Jan 1, 1958

By Joseph B. Darby, Paul A. Beck

IN isothermal sections of several ternary systems, the a-phase was found1 to extend in the form of a relatively narrow elongated field, connecting the U-phases that are present in the adjoining binary systems. This was interpreted in accordance with the conception that the U-phase is an electron compound and the ternary U-phase fields were shown in several systems' to extend approximately in the direction of constant average d-shell electron vacancy number per atom. ' However, in the various isothermal sections of the Fe-Cr-Mo system" the ternary a-phase field was

Jan 1, 1958

By R. D. Joseph

This report deals exclusively with roof-fall accidents that occurred during 1955 and 1956 in both anthracite and bituminous-coal mines throughout the United States. The report stems from a cooperative study conducted by the Bureau of Mines and the Roof-Control Committee of the Coal-Mining Section, National Safety Council. The study includes an analysis of individual accident reports, sets forth the measurable factors, and compares such factors with a representative sample of average data from 39 anthracite mines and 117 bituminous mines (appendixes A and B). Particular emphasis is placed on fatal roof-fall accidents with respect to their causes, locations, and the methods of support used at the point of occurrence. INTRODUCTION The purpose of the report is to classify all measurable details of the occurrences of roof-fall fatalities so that the material presented will assist those promoting safety and will serve as a manual for those whose principal duty is inspection of mines.

Jan 1, 1958

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By W. R. Bendy

GRINDING is a large and costly part of Portland cement manufacture. Prior to clinkering in the rotary kiln, raw materials are ground to a fineness of 80 to 90 pct passing 200 mesh. Then, after burning and cooling, the resulting clinker is ground to about 92 pct passing 325 mesh. In the cement industry the most favored method of grinding has always been by impact and attrition of a ball charge in a rotating mill. Other types of mills, in which materials are ground between die rings and rollers, or between die rings and large balls, are sometimes used for single-stage grinding and often for preliminary grinding followed by grinding in ball-type mills. Their efficiency is usually high, but maintenance and repair costs are high also, and the ball-type mill continues to be the most widely used. Together with 4 pct gypsum to retard setting time, the kiln run clinker—consisting of hard, semi-fused lumps that may have been crushed to — 1/2 in.—is ground to a Blaine surface area of 3000 sq cm per gram and about 92 pct passing 325 mesh. Approximately 32 kw-hr per ton, or 6 kw-hr per 376-1b barrel, are consumed in the grinding mills alone, not counting auxiliaries. Open Circuit Clinker Grinding: Many early clinker grinding plants employed two-stage, open circuit grinding. Comparatively short mills of large diameter, loaded with balls 4 in. and smaller, first reduced the clinker to 95 pct passing 14 mesh. Tube mills of smaller diameter and greater length, loaded with balls 11/4 in. and smaller, carried out the fine grinding operation. An early development was to assemble two or more stages of grinding in a single mill having two, three, or four compartments separated by division heads. There were difficulties in balancing the compartments, but compartment mills were popular in the 1920's because the layout was simple and there were no elevators and conveyors. Oversize Particles: Open circuit mills, whether separate ball and tube mills or compartment mills, always encountered the problem of tramp oversize in the product. A small percentage of clinker survived passage through the first grinding stage as particles—perhaps 1/16 in. diam—that were too large for the smaller balls in the following stages to reduce to —200 mesh. When the feed rate was lowered to reduce tramp oversize, there were serious losses in grinding efficiency. Many ingenious designs were perfected to incorporate perforated screen plates or wire mesh screens in the ball mills or in the first compartments of compartment mills. Their purpose was to prevent mate: rial passing out of the first stage until it was small

Jan 1, 1958

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By G. G. Sarkar

SHARPNESS of separation and washing efficiency are often confused. The sharpness index indicates the precision of a washing unit; the washing efficiency takes into account not only the unit's precision but also the washability characteristics of raw coal and the near-gravity materials at the effective density of cut. A sound basis for evaluating the sharpness index is essential in comparing the sharpness of separation attained by different cleaning units. Sharpness Index and Related Criteria: Washing plant sharpness of separation has been well represented by Hancock's efficiency chart and Tromp's curve of migrated materials. Some useful coefficients derived from Tromp's curve—the error area, probable error, and imperfection value—have been widely used to measure sharpness of separation. These are defined in a number of papers presented at the first and second International Coal Preparation Colsference held in Paris (1950) and Essen (1954).1-5 In evaluating the performance of a dense medium separator at four different gravities, Yan-cey and Greer6 bserved that even with similar operating conditions and the same size grading of feed, the imperfection value of a washing plant varies through a greater range than the probable error. The present writer also observed the same type of anomalies in comparing the imperfection values of one plant which were determined under almost identical conditions. He therefore devised a graphical method to evaluate a washing unit's sharpness of separation and define it by a single coefficient, which is substantially independent of coal characteristics under normal operation of the unit. Unlike imperfection value, the new coefficient can be expressed on a percentage basis. Coal preparation engineers generally agree that the amount of misplaced material resulting from any separation in a washing plant is almost directly related to the amount of +0.10 sp gr (near-gravity) materials. In actual practice, however, misplacement is not restricted to the 20.10 sp gr range. It will be evident from a study of Tromp curves that this misplacement often extends over unequal specific gravity ranges on the two sides of the actual density of separation. The same condition exists for near-gravity ash distribution and the resultant misplacement of ash units during any separation. But so far as the same unit is concerned, the total misplacements bear a definite ratio to the amount of near-gravity zone materials that is affected by misplacements. This ratio should be constant not only for various densities of separation but also for different qualities of feed coal treated in the same plant. This ratio, multiplied by 100, directly represents the inefficiency of the plant. When the plant inefficiency value is subtracted from 100, the re- ' sult is designated as sharpness index. Evaluating the Sharpness Index: The method of evaluating the sharpness index is explained here with reference to Fig. 1. Fig. 1 is a reproduction of the familiar diagram used by Cerchar of France to represent the inefficiency of a separation in terms of "triangle of errors," which is a measure of organic loss. It will be observed that the characteristic (yield/fractional ash) curve of the raw coal represented by GHAPR

Jan 1, 1958

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958

By F. W. Smith

To determine whether preheating coals before carbonization would improve the coking properties of the coals, particularly the weaker coking coals, 3 coals, 1 each from Illinois, Kentucky, and Pennsylvania, and a blend of the Illinois with a Pocahontas coal were preheated before testing for coking properties in the Bureau's BM-AGA pilot oven. The effects of preheating on the chemical and physical proper-ties of the coals and on the yields of carbonization products and strength of the coke produced from the preheated coals were determined, as were also the effects of bulk density, gaseous atmosphere, and residence time during preheating. Most benefit from preheating was found with weaker or oxidized coking coals, whereas the more strongly coking coals and blends showed little effect. Direct charging of preheated coal to the coke oven without cooling gave better coke, increased yield of tar, and decreased yield of gas. INTRODUCTION Although 94 percent of today's coal production comes from fields east of the Mississippi, the Eastern States have only about one-third of the Nation's recoverable reserves. West Virginia, which now produces more than any other State, has much smaller reserves than Utah, Colorado, and Wyoming.5/ However, the manufacture of iron and steel in Western States, which has increased greatly since World War I, is handicapped by the scarcity of high-grade coking coals, such as are plentiful in the Appalachian region. Unless a practical method of improving the cokemaking property of local coals is developed, ferrous metallurgical industries in the West must continue to use inferior coking coals and to pay high shipping charges for better coals.

Jan 1, 1958

By F. R. Archibald

A STATEMENT on this subject by A. D. Turnbull, presented and discussed at the Annual Business Conference of the Metallurgy Division, C.I.M., held in Ottawa on April 22nd 1957, led to creation of a committee "too see if the Metallurgy Division of the C.I.M. can improve this situation". Without discounting the general problems of education and short-ages in other fields, the committee is primarily concerned with deficiencies related to metallurgy. The committee members are: F. R. Archibald, Chairman, A. D. Turnbull, L. E. Djingheuzian, J. U. Mac-Ewan, and L. M. Pidgeon. Following exchange of views among the committee members a general attitude of approach was established and a background of reference material assembled. It is the purpose of this review to acquaint those interested with the reference material, to offer an appraisal of the situation, and to suggest a programme for action by the Metallurgy Division of the C.I.M. Before proceeding with the ?presentation it is fitting to point out that, notwithstanding some rather important developments in public concern for educational matters, as well as changes in the level of activity in the metallurgical industry, the statement (April 1957) by Mr. Turnbull still stands as a sound article of reference.

Jan 1, 1958