Search Documents

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By H. H. Bein

Most western industrial sands are feldspathic and contain feldspars in variahle amounts. A few deposits will show alumina contents of less than one per cent while others will contain over twelve per cent alumina. Some industries are not especially concerned with the amount of contained feldspar but are interested only in color and in size gradations. Other industries, however, are very much interested in alumina content and set up quite rigid specifications as to this content. Several western plants are beneficiating crude sands both to reduce the iron content and to control the feldspar content. At present, most of these plants are using flotation processes for both controls although a few plants do use magnetic separators for the reduction of iron content. Some work has also been done with electrostatic separators for the feldspar-quartz splits. The Sand Division of Del Monte Properties Company, Pebble Beach, California, has been operating a flotation plant for iron removal and the separation of quartz and feldspar since 1950. As mentioned before, control of alumina, especially in the quartz product, is very important. Some users require an alumina content of less than two per cent and others will demand a product of less than one per cent Al2,O3,. The standard Quinolate method for determining alumina is lengthy and time consuming. The HF —H2SO4 evaporation step is especially critical and, if forced, spattering is apt to occur with a resulting loss of sample. Standard procedure is to evaporate to dry ness overnight at a low temperature. Even with forcing under optimum conditions the procerlnre will take two or three hours to complete. A new method has been developed which allows an alumina determination to be made, in 10 or 15 minutes, on a sample of the quartz product as it is being produced. This pocedure, although simply an approximation, has been most helpful in showing whether or not the product being formed is meeting specifications. This procedure has also allowed a great reduction in samples formerly taken and analysed by the orthodox method. Whether a sample assays 1.75% A12O3, or 1.95% .41,0, is not so important as the fact that it is below the allowable maximum of 2.00%. Similar thinking would apply to products required to contain less than 1.00% A1,0,. The step by step procedures for the method are as follows: 1. Collect sample, drain or filter, and dry. 2. Split sample through standard Jones sample cutter to quarter or eighth sample, depending on size of original sample taken, then split down to about 5 grams through Sepor micro-splitter. 3. Screen through 50 mesh sieve (U.S. Series) and reject undersize. 4. Weigh out 2 grams and place in platinum crucible. 5. Etch with 3-5 mls 38.40% HF for 1 minute at room temp. 6. Decant and wash. 7. Stain for two minutes in same crucible with a 1% water solution of Nigrosene dye. 8. Decant and wash well. 9. Dry.

Jan 1, 1961

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By R. F. Stewart

A sedimentation method involving the use of the Palo-Travis apparatus was found satisfactory for rapid determination of the size distribution of coal particles ranging from 10 microns in diameter to those passing an 840-micron opening (20-mesh sieve), The method is most useful for comparing the size distributions of samples of pulverized coal where the actual size of the particles is not required and is applicable to sieve and subsieve sizes of a wide variety of coals and chars that can be wetted and are heavier than water. An analysis, including all calculations, can be completed in 1/2 to 10 hours, depending on the time required for the finely divided coal to settle. A typical analysis requires about an hour, making this a rapid, precise method for routine size-distribution analysis of powdered coals. When used with coal particles smaller than 400 microns, the method is precise within 15 microns for wide variations in test conditions and within 5 microns for identical test conditions. The precision decreases as particle size increases, becoming unsatisfactory for particles larger than 400 microns (40-mesh). For precision within 15 microns, the samples must be equal in weight. Greater precision is obtained with 4-gram samples, but samples as small as l gram may be used.

Jan 1, 1961

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By H. N. Treaftis, J. W. Cahn

THE previous determinations of the solvus of tin in solid lead disagree with one another by as much as 40°C or almost 10 at. pct. Even determinations that appear to be careful differ considerably in both the solubility and its temperature coefficient. Recent kinetic workl -3 on the rate of precipitation of tin from lead-tin alloys and thermodynamic work4 on the heat of solution of tin in lead have given some insight into the time necessary to reach equilibrium in this system. As this time is longer than that used in almost all previous determinations of the solvus, these determinations are questionable. Since the interpretation of recent kinetic results requires accurate values of the equilibrium solubility the present work was undertaken. DISCUSSION OF PREVIOUS RESULTS The methods used in previous studies may be placed into three classes: 1) Several alloys covering a range of compositions are allowed to reach "equilibrium" at a certain temperature.5-7 Some property, such as the X-ray lattice parameter of the lead-rich phase or the re- sistivity of the alloy, is then measured as a function of composition. The solubility limit for that temperature is taken to be that composition at which a discontinuity in the property occurs. However, the recent kinetic work has shown that tin precipitates in two stages. The first stage is rapid but leaves the lead still supersaturated. The second stage is very slow, and it seems from the equilibration times quoted by the investigators of the solvus that the end of the first stage of precipitation was usually mistaken for equilibrium. This is especially true at temperatures below 100°C where the first reaction is still quite rapid (from minutes to months), but where the second stage is so slow that very long holding times are required to reach equilibrium. Alternatively micrographic work8 on several alloys of different compositions seems to have given good results if done carefully. 2) The beginning of precipitation in a homogenized alloy is measured as it cools slowly8-10. Since reactions in solids undercool easily, such determinations will always give too low a temperature for the solvus. 3) Some property of an alloy is measured as a function of temperature while the alloy is above the solvus.5,9,11 The range of temperature can usually be extended slightly into the two phase region. Then the alloy is precipitated at a much lower temperature and slowly reheated. The solvus is taken to be the lowest temperature where the property of the reheated alloy is equal to that previously determined for the homogeneous alloy. Usually one also expects a discontinuity at the solvus in the temperature variation of the property for the reheated alloy. The difficulty in this method is the sluggishness of the dissolution process, and this method may give too high a solvus temperature. EXPERIMENTAL The phase boundary or solvus temperature was determined by a modification of method 3 for a series of chemically analyzed high-purity alloys, ranging from 5.1 to 26.4 at. pct Sn. The resistance, as a function of temperature, of a sample of homogenized alloy (which could easily be undercooled) was compared with the equilibrium resistance which that alloy sample attained after precipitation at room temperature followed by long isothermal anneals at various temperatures. Before each anneal the sample was rehomogenized and reprecipitated. The solvus temperature could be located to within 1°C as the intersection of the resistance vs temperature curves for the homogenized and equilibrium alloys. No attempt was made to locate the phase boundary more accurately since the limiting factor was the precision with which the alloys could be analyzed. This precision was ±0.1 wt pct Sn and corresponds to an error of 1 deg in temperature. This use of isothermal anneals differs from some of the previous investigations in which method 3 was used with baths of slowly rising temperatures. It was found early in the investigation that solvus temperatures tended to be high if the latter method was used even at extremely slow heating rates. For example a

Jan 1, 1961

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By C. E. Melbye

A serious problem confronted the city of Gunnison early in 1958 in that, for a few months during each spring runoff, the water supply derived from the Gunnison River became polluted to an unsafe point. The city management had the choice of building a new filter plant to replace the old unworkable one or drilling wells to develop a ground water supply. The cost of a new filter plant was estimated at $180,000 compared to $50,000 for 6 wells, pumps, and additional water lines, hence their decision to attempt the development of sufficient ground water. Six wells at 300 gpm per well were estimated as necessary to handle the peak usage of 1800 gpm, compared to only 600 gpm winter usage. Although the water table is only about 7 feet below the surface, existing private wells drilled at random locations were producing much less than 300 gpm. The problem was to find sufficient quantities from about 6 wells. Since the presence of an ancient bedrock channel was suspected, which would be expected to localize greater quantities of water, the city of Gunnison authorized a resistivity survey to investigate bedrock topography below unconsolidated gravels. Survey results were highly satisfactory and led to the preparation of a fairly detailed bedrock contour map, Fig. 1. This map was used in selection of all well sites. The city of Gunnison is situated in a flat, broad, Quaternary gravel-filled valley (terrain dips south at 20 feet per mile) at the junction of the Gunnison River and Tomichi Creek. The valley, about 2-4 miles wide, is bordered by hills of Tertiary volcanics to the northwest, Cretaceous and Jurassic sediments to the north and northeast, and pre-Cambrian granite and gneiss to the south. One previous deep test well at the west end of the city hit pre-Cambrian granite at 496 feet, which, allowing for 40 feet of surface gravels, makes the older sedimentary section 456 feet thick. This section is probably all Jurassic Morrison formation, consisting of the Saltwash sandstone overlain by the much thicker section of Brushy Basin shales and mudstones. According to the driller's logs, each well was bottomed in what is believed to be Brushy Basin shale. FIELD PROCEDURE A standard Gish-Rooney type of resistivity apparatus was employed, which used 45-volt dry batteries as a direct-current power source. Applied voltages could be selected from 45 volts to a 270-volt maximum. Copper-coated steel stakes were employed as current electrodes and porous porcelain pots as potential electrodes to avoid possible polarization effects with direct current. The expanding Wenner electrode configuration was utilized for this investigation and measurements were made at 20 40, 60, 80, and 100-foot spacings,

Jan 1, 1961

By D. J. Hains

IN this paper we shall examine the Why, Where and How concerning the agglomeration of iron ores and concentrates. Fig. l answers the questions @f why there is so much interest at the present time in the art of agglomeration. The use of sinter or pellets in the blast furnace has materially increased their rated •capacity. ':'President Hains Company Ltd. Engineering J. S. McMahon ( 1) reports an increase from 653 tons of .pig iron per day to 1140 tons of pig iron per day with the use of a 100 per cent sinter burden on one of his blast furnaces. In the United States the use of 100 per cent pellets has increased pig iron production from approximately 1800 tons per day to over 3000 tons pig iron per day (2). In our economic system the general objective is to produce more and better commodities cheaper. Fig. 2 shows the decrease in coke consumption with increased tonnages from the furnaces when using -

Jan 1, 1961

By Raymond G. Travis

This paper, which describes mining methods and practices at the Hurricane Creek bauxite mine of Reynolds Mining Corp. in central Arkansas, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Hurricane Creek mine is in sec. 12, T. 2 S., R. 14 W., and sees. 7 and 18, T. 2 S., R. 13 W., Saline County, Ark., about 4 miles east of Bauxite. (See fig. 1.) Bauxite has been mined underground at the Hurricane Creek property since 1942. The operation is notable for relatively high recovery of bauxite under the adverse conditions of unconsolidated water-bearing overburden and unstable clay floor. Controlled caving, timbered stope walls, and efficient drainage systems on the surface and underground have minimized the problems and raised ore recovery about 25 percent above that formerly obtained.

Jan 1, 1961

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By W. H. Boyer, J. W. Gabelman

The concept of metal zoning has long been recognized (Spurr, 1907, 1923; Emmons, 1924, 1926; Lindgren, 1933; Rateman, 1950), although it has been considered indistinct for most epithermal districts. The geometric relation of barren zones of hydrother-mally altered rock to ore deposits was emphasized in the work of Lovering (1941, 1949, 1950), Sales and Meyer (1948, 1949, 19501, Burbank (1941, 1950), Schwartz (1939, 1950), and Kerr (1947). Lovering (op. cit.) and Sales and Meyer (op. cit.) emphasized the consistent presence of barren alteration envelopes enclosing individual ore bodies, particularly of the vein type. Schwartz (1950) noted a difference between the distribution of alteration zones described by Lovering and by Sales and Meyer, as compared with those associated with the porphyry copper deposits of the Southwest. The disseminated deposits of the Southwest usually occur within large bodies of altered rock whereas most veins do not. In the following discussion the mineralization process is conceived of consisting of two distinct phases: pre-ore nonmetallic alteration and metallization. In the present investigation the position, size, and shape of all known hydro thermally altered areas and the position, size, and metal type of all known ore deposits were plotted on base maps of southwestern and west-central Colorado (Figure 1). The maps indicate a generally consistent geometric relation between altered and metallized areas. The addition of alteration to the pattern of metal deposits establishes a temperature zoning pattern of much greater clarity than that formed by the epithermal metal deposits alone, and allows a more precise definition of mineral belts. The center of strongest mineralization is indicated to be the area of greatest barren alteration, and metal deposits are grouped about it both under structural control and crudely in response to temperature zoning. The combination of an area of strong alteration and associated marginal clusters of metal deposits is defined as a mineral district. The strong similarity in individual deposits, in groups of different types of deposits, and in the alteration-metallization relation in districts throughout the region implies that a single metallogenic province is represented in southwestern and west-central Colorado. The occurrence of deposits in Tertiary voi-canics indicates a late Tertiary metallogenic epoci., although an early Tertiary epoch is known locally as at Ouray. Patterns formed by mineral districts can be

Jan 1, 1961

Jan 1, 1961

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

[Appalachian Petroleum Section: Chairman: Robert H. Edele, 1st V.C.: Robert Vutech, 2nd V.C.: Robert Tullis, Sec.-Treas.: Frederick T. Solomon. Meets last Tuesday of each month in Charleston, W. Va. Balcones Section: Chairman: Dr. Frank W. Jessen, 1st V.C.: Gilbert M. Andreen, 2nd V.C.: Lloyd N. Johnson, Seo.-Treas.: W. C. Vercellino. Big Horn Basin Subsection: Chairman: B. E. Yester, 1st V.C.: Robert J. Woodhall, 2nd V.C.: Herbert A. Koch, Secretary: Dean Costello, Treasurer: Thomas W. DeLong. Meets 2nd Wednesday; alternating between Cody and Worland. Billings Petroleum Section: Chairman: George O. Ellis, 1st V. C.: Robert L. Spottswood, 2nd V. C.: Robert M. Watkins, Sec-Treas.: Joseph H. Bato. Meets 5:30 p.m., 3rd Tuesday at Billings Press Club.]

Jan 1, 1961

By M. O. Holowaty, C. M. Squarcy

1750 to 1850: The scene shifts westward across the Alleghenys to the young town of Pittsburgh; charcoal gives way to mineral coal as furnaces grow larger and the blast is heated; above all, Pennsylvania iron is adding strength to the new Nation and building an empire in the West. TWO names are inseparably associated with the Pittsburgh iron industry-those of George Anschutz and John Hayden. The iron ore deposits of southeastern Pennsylvania were found and developed early in the 18th century, and several forges and furnaces were built and operated. It was only after the revolution that the iron men crossed the Susquehanna River, built furnaces in the neighborhood of ore deposits of Franklin County, then along the Juniata River and its valley. Juniata Iron found a ready market in the Pittsburgh area. However, difficulty in transporting it across the Allegheny Mountains induced iron mas¬ters to seek ore and plant locations in the Pittsburgh district. One of the first to reach this area was George Anschutz, who migrated to America in 1789 at the age of 36, reaching Pittsburgh in the fall of 1790. Anschutz immediately set out to organize an iron company in Pittsburgh, and was able to interest some residents in his project. After being informed of an iron ore deposit located only three miles out of town (on the site of the present 26th St. and the Allegheny River) he decided to build there his blast furnace and foundry plant. Total cost of the installation was $300. When the furnace was put in operation, Anschutz, now known as Red George, found that the ore deposit was only an insignificant one and would last no more than a few weeks. A new deposit was found on Roaring Run, in the southeastern corner of Armstrong County. Anschutz transported some of this ore to the mouth of Two Mile Run, where it was loaded on horse wagons and transported to the furnace. In this way, he operated off and on for several months, until the furnace was blown out in 1794. After working for a year as plant manager for John Probst at Langhorntown, he built the Hunting-

Jan 1, 1961

By H. D. B. Wilson, W C. Brisbin

The Thompson-Moak Lake nickel belt lies along the root of a Precambrian mountain range of the island-arc or alpine type. This range coin-. cides with the boundary between the Superior and Churchill blocks of the Canadian Precambrian shield. The nickeliferous peridotites and nickel ores occur along a negative gravity strip, which also coincides with strong thrust faulting and the axis of greatest deformation of the mountain range. Similar structures and highly nickeliferous peridotites occur in present-day island arcs. Much of the belt is covered by Paleozoic rocks, but a length of 270 miles may be explored by present-day methods. Nickel deposits have been located along 60 miles of the belt. The length of the favorable structure and the size of the known deposits suggest that this will be one of the world's major nickel regions. The regional gravity anomalies, which consist of a branching negative strip bordered by two positive strips, are best explained by major warps of a crust consisting of a granitic and basaltic layer. The ore deposit

Jan 1, 1961

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961