Search Documents

By H. Warlimont

In recent investigations of the microstructure and crystallographic features of martensite by electgon microscopy,', '9 thin films (about 50 to l000A in thickness) have been used as specimens. It was found by W. Pitschl ,2 that the lattice relationships between the supefiaturated fcc matrix and the martensite formed in thin films were different from those observed after transformation in bulk material. Corresponding differences are to be expected in nucleation and in reaction kinetics in the formation of martensite in thin films, but have not yet been reported. In the course of the preparation of thin films of iron-base alloys for investigation by electron microscopy it was observed that films of alloys, whose martensite formation temperature (Ms) was below room temperature, formed martensite during the electrochemical thinning process conducted at or above room temperature. The chemical compositions and approximate bulkM,-temperatures of the three materials on which this observation was made are listed in Table I. The alloys were vacuum-melted from high-purity metals. It can be seen that the effect occurred in alloys that contain only sub-stitutional components as well as in alloys that contain carbon as an interstitial solute. The appearance of martensite formed in this manner is illustrated in Fig. 1, which represents a polished film of alloy No. 1 at XI0 magnification. The martensite plates can be recognized by their surface relief effects. In addition, heavily strained (owrinkledo) austenite can be seen near the edges of the film where it is thinnest and transformation stresses or strains can be accommodated by plastic deformation most easily. The nonuniform distribution of transformed regions is probably due to the varying thickness of the film. These observations were common to all materials listed in Table I. Because effects of supercooling or straining can

Jan 1, 1962

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By Charles White Merrill, James W. Pennington

No metallurgical process developed in the 20th century compares with froth flotation in its effect on the mineral industry. Processes like gravity - concentration, amalgamation, and pyrometallurgical reduction are of ancient origin; others like cyanidation and electrolytic reduction were well established by 1900. Such metallurgical processes as heavy-media separation, ion-exchange, and solvent extraction belong to this century, but their influence is small compared with froth flotation. Data collected by the U. S. Bureau of Mines* in a canvass of 202 froth flotation plants reveal that, in 1960, 198- million tons of material was treated to recover 20-million tons of concentrates which contained approximately $1 billion in recoverable products. SIGNIFICANCE OF FLOTATION Froth flotation as described in this chapter refers to a wet process for separating properly ground mineral particles into two or more products. It involves the separation of mineral particles from each other in a liquid pulp by means of air bubbles. Finely crushed ore is agitated in water with the addition of air or other gases. Various chemicals and oils are added to cause the selected mineral particles to attach themselves to the air or gas bubbles. These bubbles, carrying the mineral particles, rise to the surface where they are removed in a froth, while the other particles remain suspended in the pulp. The earliest flotation divided the raw material into two products: a bulk concentrate that was removed as a froth and a tailing that remained in the flotation machine. The froth usually contained the valuable constituents. The successful application of such a process depended on the recovery of a single concentrate from which one or more valuable constituents could be recovered by a chemical or smelting process. With the advance of the art, however, the principle of selective flotation, by which two or more relatively pure products could be recovered from complex raw materials, was evolved. Other chapters in this volume describe the developments during the last 50

Jan 1, 1962

By Paul A. Beck, M. N. Parthasarathi

The vecrystallization texture. formed by selective growth of random nuclei in an 80 pct volled 99.997 pct A1 crystal of initial orientation mear (123) (41.21 was found to consist of components related to the single-component rolling texture by 40 deg. rota-tiows around [111]axes. The relative-volume fractiovz of the various recrystallization-texture componezts may be accouzted for 012 the basis of the Lou) mobility of twist boundaries, if it is assumed that the mobility of the tilt boundaries also varies with their orientation. Similar results with a, aluminum-alloy cystal of the (110) [112] orientation, containing iron, silicon, and zinc, show that these solute contents do not impair the effectivezess of the oriented growth mechanism of re cry s-tallization- texture formation. In a previous investigation1,2 it was found that a sharp recrystallization texture is formed as a result of the oriented growth of random artificial nuclei in an aluminum crystal rolled to 80 pct RA, on the (110) plane in the [ 112] direction. Four recrystallization-texture components were found to occur, with orientations corresponding to 40-deg rotations around [111 1 axes of the deformation texture. Reorientations of this type were already found in earlier work,3,4 where the presence of random nuclei could be reasonably assumed, but was not rigorously documented. The same orientation relationship was found also by Lucke and Liebmann, who actually measured the orientation dependence of boundary-migration rates in the recrystallization of A1 crystals slightly deformed in tension.5,6 The occurrence in the recrystallization texture of only four of the eight crystallographically equivalent orientations of the type referred to above remained unexplained,1,2 although it was clearly not a result of the absence of suitable nuclei. Recently Burgers7 suggested that this effect may be due to the aniso-tropy of boundary mobility observed2'6; it was found that the recrystallized grains of the 40-deg [111]-rotated type grow much faster in directions perpendicular to the [ 111] they have in common with the matrix than parallel to this direction, i.e., the tilt boundaries have much higher mobility than the twist boundaries. The four orientations corresponding to

Jan 1, 1962

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By R. L. Brown, E. A. Swanson

THE Buchans ore bodies are located in central Newfoundland, three miles north of Red Indian lake. The townsite of Buchans was named after a Royal Navy Captain who, while attempting to make contact with the Beothuck Indians, camped in the area in 1820. Ore was first found at Buchans by a Mic Mac Indian, Matty Mitchell, who discovered one of the three small orebodies in the bed of the Buchans river. The Anglo-Newfoundland Development Company, which holds mineral rights in the area, developed the orebody, but was forced to give up the venture because of difficulties encountered in separating the various sulphides. The American Smelting and Re-fining Company developed a flotation process which was capable of economically separating and concentrating the various sulphides, and, in 1926, they took a long-term lease on the property.

Jan 1, 1962

By R. S. Olson

The operation of a series wash thickener-two stage filtration circuit determines the soluble loss in many hydrometallurgical operations A study of this circuit yielded expressions which permit calculation of soluble loss for almost any condition of operation. The soluble loss over a range of the circuit variables is presented to illustrate and evaluate circuit performance, The interrelation of factors affecting filter performance and some of the wash circuit, variables are quantatively described. Filter wash, which is governed by wash zone size, filter pulp level and filter feed pulp density, has the greatest affect on soluble loss. Excepting clothing blinding and flocculation the factors which decrease filter capacity also decrease soluble loss. Repulping with water, under some circumstances, can bean important means of soluble loss reduction. Water for primary filter wash, leach pulp density repulp density and wash thickener underflow density have little effect on soluble loss. The dilution of both o the filter pulps with wash solutions is suggested as a means of reducing soluble loss, and at the same, time, controlling the performance of the filters. Blowback and filter cloth blinding seriously increase soluble loss.

Jan 1, 1962

By F. R. Brotzen, J. Taranto

SEVERAL investigators have computed stacking-fault concentrations from X-ray diffraction data.'-' The method generally employed relates the line shift to the stacking-fault probability. In this investigation platinum filings of 99.99 pct purity screened to -325 mesh were studied after having been subjected to various annealing treatments. The lines were measured on a General Electric XRD-5 spectrogoniometer using CuK, radiation. The centroid of the broad reflections was determined by the method proposed by pike.' The stacking-fault probability was calculated by the formula given by Warren and warekois,3 with the assumption that all stacking faults were on the (111). Various high-angle reflections were used, but most data collected refer to the shift in the (400) reflections. When the filed platinum powder was annealed at 1200°C for 20 min the stacking fault concentration was too small to be detected. The stacking-fault probability in freshly filed specimens, as determined by the line shift relative to the annealed specimen, was about 0.016, Fig. 1. If the faults would be created only by extended dislocations, the dislocation density in the filed specimen would be about 3X1012 cm-2. The average stacking-fault width of about 21 which was used in this computation, is that given by Thornton and Hirsch.7 The mechanism by which stacking faults are annihilated during annealing is not yet fully understood. The isothermal results obtained do not seem to support the simple hypothesis of a first-order decay. On the other hand, the analysis by Kuhlmann, Masing, and Raffelsieper8 for the loss of dislocations during recovery agrees much better with the experimental data of this investigation. This analysis yields an activation energy of 29 ± 8 kcal per mol for the disappearance of stacking faults in cold-worked platinum during annealing. Even if one takes into account the lack of accuracy inherent in this X-ray method, the activation energy found is substantially less than that of self-diffusion in platinum, i.e., 61.6 kcal per mol.9 The results therefore suggest that processes other than dislocation climb, which involves the activation energy of self-diffusion, are responsible for the loss of stacking faults in platinum during annealing. The broad reflection lines became sharper early in the recovery process, Fig. 1. The sharpening occurred well before the stage during which stacking faults disappear. This lends support to Nowick's10

Jan 1, 1962

By E. P. Abrahamson II

The effect of transition element binary solid-solution additions upon the recrystallization temperature of vanadium has been investigated. Cr, Fe, Co, Ni, Mo, Ru, Rh, Os, and IY lower the recrystallization temperature, while Ti, Mn, Zr, Cb, Pd, Hf, Ta, W, Re, and Pt raise it. The majority of elements have their greatest effect in less than 0.15 at. pet. Both the rate of change of recrystallization temperature with atomic percent solute and the limit of initial linearity are found to Correlate with the free atom grozdnd state outer electron configuration of the sollte element. THE work of Abrahamson and Grant1 and Abraham-son and Blakeney2 has shown that the solute's elec- tron configuration appears to be a prime determinant of both brittle-to-ductile transition and recrystallization temperature in dilute binary alloys. It has also been shown by Abrahamson3 that the limit of linearity, i.e., the limit of initial linear change of recrystallization temperature with atomic percent solute, is also a function of the electron configuration of the solute in iron base alloys. Because of the systematic nature of the solute electron configuration correlation, it is to be expected that some systematic variation might be observed upon changing the solvent. Thus, this study of recrystallization in vanadium base alloys is the first of a series aimed at defining the role played by the electron configuration of solute in determining the recrystallization characteristics of dilute transitional alloys. PROCEDURE All alloys were made using 99.8 pct V containing 0.011 C, 0.024 N, 0.08 0, 0.006 H, 0.035 Ta, and

Jan 1, 1962

By W. M. Albrecht, W. D. Klopp, R. I. Jaffee, B. G. Koehl

Kinetic studies were made of the reactions of tantalum with oxygen, nitrogen, and air at 400o to 1500°C. The tantalum-oxygen reaction is linear from 500° to 1250°C. The tantalum-nitrogen reaction follows a cubic rate law at 400° to 700°C and a parabolic rate law at 800" to 1475°C. The reaction behavior in air is initially parabolic followed by a transition to linear behavior. In the search for high-temperature materials, considerable interest is being shown in the refractory metal, tantalum. It is the third highest melting metal with a melting point of 2996°C. Also, tantalum has excellent ductility, making it one of the most workable refractory metals. In considering high-temperature applications of tantalum, the oxidation kinetics of the metal must be known. Such information also serves as a basis for the development of corrosion resistant tantalum-base alloys. Therefore, this study was made to investigate the reaction of tantalum with air, nitrogen, and oxygen. LITERATURE Several oxides of tantalum have been reported. The pentoxide, Taz05, is the only oxide of tantalum whose identity has been established. A high-temperature modification, aTa2Os, has been reported by several investigators.1-4 A low-temperature phase, ßTa2O5, undergoes an allotropic transformation at 1320o to 1350oC. 5-8 Four other oxides of tantalum have been reported. The oxides TaO2, TaO, and Ta4O have been reported by schonberg.9 A suboxide Ta2O, was observed by Wasilewski 6. However, the presence of oxides lower than Ta2O5 is questioned by Lagergren and Magneli.7 In oxidation studies, vermilyeal0 and Peterson, et al.,12 reported one possible phase intermediate between Ta and Ta2O5. Only Ta2O5 was formed in the tantalum air reaction, as reported by Michae1.l3 Several studies have been made on the kinetics of the tantalum-oxygen reaction. vermilyeal4 investigated the range 50° to 300°C and found that the rate of growth of a thin adherent oxide film could be described by the Cabrera-Mott theory. Gulbransen and Andrew15,18 studied the reaction kinetics of tantalum in oxygen pressure of 1/10 atm at 250° to 450°C. At all temperatures the reaction followed the parabolic rate law for periods up to two hours. The oxidation behavior in the range 500" to 1000°C was found to be linear at oxygen pressures of 0.2 to 600 psi according to Peterson. et al.l1 At very low pressures (1 x 10-3 to 2 X lo-' mm of Hg) Gebhardt and seghezzi17 reported linear oxidation at 800° to 1500°C. The reaction of tantalum with air is similar to the reaction with oxygen. Studies have been made by Waber, et a1.,12 and Michae1.l3 Two nitrides of tantalum, TaN and Ta2N are known. Their structures have been determined by Brauer and Zapp 18,19 The tantalum-nitrogen reaction kinetics have been investigated by Gulbransen and Andrews. 15, 16 The reaction follows the parabolic rate law at 500° to 850°C at a nitrogen pressure of 1/10 ,atm. At the same temperature, the tantalum-nitrogen reaction is much slower than the tantalum-oxygen reaction. EXPERIMENTAL TECHNIQUES Material— The material used in this study was high-purity, electron-beam-melted tantalum obtained from the Temescal Metallurgical Corp. The hardness of the as received ingot was 76 Vhn. The analysis of the material is given in Table I. Methods—Cylindrical specimens of tantalum approximately 0.9 cm in diam and 0.5 cm in length

Jan 1, 1962

Early theories of coal formation are outlined, with special emphasis on the arguments for allochthony and autochthony. Various aspects of the nature, growth, and decay of the characteristic vegetation of the brown coal peat moors, their conversion into coal, the origin of banding, and the influence of tectonics are discussed.A description of the banding in Victorian brown coals is followed by a discussion of their vitrain, fusain, and natural carbonized coal; and concludes with the nature of the coal resin and the possibilities of its extraction.The nature and derivation of inorganic matter in brown coal, based on Lessing's classification, is described. Assimilation of mineral substances in specific plants with variations due to environmental factorsare illustrated by analyses of present day trees. Consideration is then given to possible sources of salt, marcasite, and quartz in brown coal.It is shown that part of the inherent and extraneous ash may have been removed during and after coal formation. The nature and abundance of the organically combined substances in brown coal emphasizes the anomalies that may arise from estimating the total inorganic matter from ash contents.After classifying deposits on external heating surfaces of boilers, theoretical and practical aspects of slag formation, alkali matrix deposits, and the effect of sulphur and chlorine are considered.Analyses of deposits in boilers burning Victorian brown coal are tabulated.Slagging at the Yallourn power station from sand in the Yallourn open cut, and difficulties with Yallourn North Extension coal at the Maryvale paper mills are described.Tests carried out on Morwell and Yallourn coals showed that with the former, impacted deposits formed on boiler heating surfaces, and left a high percentage of chlorides on probes. Morwell briquettescompared with Yallourn briquettes also reduced the running time of a semi-industrial boiler through deposits with sodium sulphate as...

Jan 1, 1962

By W. C. Hagel, J. H. Westbrook

Usittg a sectioning technique with Agl10 as the tracer, the diffusion of silver in silver-excess (45.8 at. pct Mg), near-stoichiometric (49.8 at. pct Mg), and magnesium-excess (52.0 at. pct Mg) cylinders of CsCl-type AgMg was determined from 500" to 700°C. Diffusion coefficients conform to the expression D = Do exp (-q/RT) where the respective Do values are 1.53, 0.280, and 0.134 sq cm sec-I and the Q values are 41.3, 40.6, and 38.0 kcal g-atom-'. Lnttice-parameter and density measurements were performed on a more numerous assortment and wider range of compositions. Substitutional defects were found on both sides of stoichiometry. Activation energies for other rate processes in these alloys show related trends with changing composition, although silver may not be the rate-detemining species. KNOWLEDGE of diffusion coefficients is necessary for a quantitative understanding of the many rate processes (e.g., grain growth, precipitation, sintering, oxidation, or mechanical deformation) occurring in solids. Although these data are available for most metals and common alloys, they are quite limited for intermetallic compounds—a group of materials whose unique physical and mechanical properties are presently attracting great interest. From a fundamental viewpoint, diffusion in intermetallic compounds also offers several engaging aspects owing to: their ordering, the possibility of introducing large, stable concentrations of lattice defects, and the variety of bonding types and crystal structures which can be found. In the case of CsC1-type compounds, some previous work has been directed at examining the role of vacancy defects by changing their concentration compositionally. The diffusion of Co60 was measured in 0 NiAl1- and in P COA., Except for the results of Smoluchowski and Burgess, isothermal diffusion coefficients were found to pass through a minimum at the stoichiometric composi- they decreased sharply on what was reported by Bradley and co-wrkers' to be the vacancy-rich (aluminum excess) side of stoichiometry. This investigation of the diffusion of Agl110 in AgMg was undertaken both as an adjunct to a concurrent study of its deformation behavior and for the purpose of obtaining information on the influence of lattice defects and temperature on diffusion in another CsC1-type intermetallic compound. Bcc AgMg remains ordered up to and melts congruently at 820°C. Solubility limits at 300°C are about 41 at. pct Mg and 53 at. pct Mg. It is one of the Hume-Rothery electron compounds with a 3/2 electron-atom ratio. Previous investigations of its properties include hardress,' tenile,'-' electrical reistivity, and thermodyna-mic1',14 studies. Indications of a high bonding strength may be found in the large heat of mixing1' and in the 6-pct vol contraction on compound formaticp, as calculated using atomic radii of l.40 and l.55a for Ag and Mg. EXPERIMENTAL PROCEDURE Alloys were prepared by the induction melting of selected fine silver (99.95) and low-iron magnesium (99.95) in magnesia crucibles under 1 atm of A. Supplied by the Handy and Harmon and Dow Chemical Cos., respectivelv. Melts were poured under argon into graphite molds providing 1 1/8-in.-diarn. by 4-in.-long ingots. These were homogenized in evacuated and argon-filled fused-silica capsules by heating for 16 hr at 750'. Three 1 in.-diam. by 3/4-in.-long cylinders were machined from the mid-portion of each ingot for diffusion measurements. Three alloys, analyzing 45.8, 49.8, and 52.0 at. pct Mg were taken as representing the extremes of interest, with 49.8 at. pct Mg being very close to the stoichiometric composition of 50.0 at. pct Mg.

Jan 1, 1962

By G. M. Schwartz, J. N. Gundersen

John W. Gruner (Professor Emeritus, College of Science, Literature, and the Arts, Dept. of Geology, University of Minnesota, Minneapolis) — It is surprising that two men as well acquainted with the taconite rocks of the Mesabi District as Drs. J. N. Gundersen and G. M. Schwartz should have concluded that the taconite of the Eastern Mesabi before the intrusion of the Duluth gabbro consisted largely of quartz and magnetite. These minerals were "locally reconstituted" into "a wide variety of silicate mineral assemblages" by the gabbro. It is well known, of course, that the silicate mineralogy of the Eastern Mesabi ('about 14 miles in length) is quite different from that of the Main Mesabi which is over 60 miles long. The change from one to the other is abrupt and cannot be attributed to any other cause than the thermal effects of the gabbro. Are we to assume or believe that the taconite of the Eastern Mesabi was radically different from that of the Main range before the gabbro metamorphosed it?

Jan 1, 1962

By C. H. Li, R. J. Stokes, T. L. Johnson

The effect of alumina particles on the nucleation and growth of cracks through a silver- chloride matrzx has been investigated. It has been found possible to promote fibrous cracking in dispersion-strengthened silver, chloride under notch-impact conditions at temperatures at which silver chloride alone cleaves brittlely The modification) of fracture beIzavzor is thought to be due to the relaxation of hydrostatrc stress beneath a notch by the nucleation of cavities near alumina particles. In recent years, composite or dispersion-strengthened materials have been studied primarily to understand their high resistance to plastic flow particularly at elevated temperatures. Dislocation models have been developed with which it is possible to deduce with fair success the effects of interparticle distance, particle size, temperature, upon yielding and creep behavior.l-4 Much less attention has been paid to the fracture behavior of these materials (with the notable exception of common structural steels) and little is known experimentally about the manner in which inclusions affect the nucleation and growth of cracks through a matrix. Nevertheless a beginning has been made in connection with fibrous cracking in ductile matrices where inclusions appear to play an essential ro1e.5-7 During the severe localized plastic deformation which accompanies necking in a tensile test, cavities are believed to develop at inclusions; these cavities subsequently grow and coalesce by plastic flow until separation is complete. It is of interest to consider whether inclusions can affect fracture behavior under loading conditions which restrict the plasticity of the matrix itself (for example, cleavage under conditions of a high imposed strain rate at low temperatures). It is particularly interesting to study these effects in a solid which shows a spectrum of behavior ranging from fully ductile to semi-brittle behavior. Such a solid is silver chloride whose mechanical behavior depends sensitively upon temperature and strain rate.'," The present paper is concerned with a study of the influence of inclusions (in the form of alumina particles) on the fracture behavior of silver chloride loaded uniaxially at low strain rates at room temper- ature and also under notch impact conditions over a wide range of temperature. In particular, it will be shown that the alumina particles can exert a startling effect on the ductile-brittle transition temperature of notched silver chloride and that the magnitude and nature of the effect depends upon both the quantity of alumina and the shape of the alumina particles. 1. EXPERIMENTAL PROCEDURE 1.1 Materials Used. Silver chloride powder of analytical reagent (AR) quality having an average particle size 6 was supplied by the Mallinckrodt Chemical Works (st. Louis, MO.). Acid washed 900 mesh alumina powder, designated A38-900, was supplied by the Norton Co. (Cambridge, Mass.). This powder was added to silver chloride in two forms: a) the as-received condition in which the individual particles were of random irregular shape; their statistical average size was 7; b) in a condition in which each particle was spherically shaped by a fusion technique. In this case, the statistical average particle size determined with the optical microscope was approximately the same (about 5p) but electron micrographic evidence indicated that many ultra fine particles were present in the spheroidized powder. 1.2 Preparation of Composite Materials. Silver chloride-alumina composites containing 2.5, 5, and 15 pct by volume of alumina were produced by the extrusion of mechanically mixed powders blended in a ball mill for 24 hr at room temperature. The mixtures were compacted at 50,000 psi at room temperature in the form of billets 3/4 in. in diameter and 1 in. long which were then extruded with a 16:l reduction ratio at 370°C through a radius-type steel die having a 5 deg lead-in angle. An extrusion temperature of 370°C was selected to ensure that all composites had sufficient plasticity to be extruded. Apart from this general requirement, the choice was arbitrary. 1.3 Microstructure of Composites. Attempts were made to check the distribution of alumina metallo-graphically by polishing transverse and longitudinal sections of the extruded rod. Specimens were wet-ground to 600 emery paper and lapped successively with 5 and 0.25-p grades of diamond paste. They were etched for 10 sec in 10 pct sodium thiosulfate solution and lightly polished in concentrated ammonium hydroxide. The most effective way to render the alumina particles and grain boundaries visible was to radiate the surface with intense white light to decorate the grain boundaries and the particle-matrix interfaces photolytically.

Jan 1, 1962

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962