Search Documents

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By Arthur Miller

Most of the production of copper in the United States comes from a few large companies. Often overlooked, however, are the more numerous small mining operations, which collectively produce a significant portion of the nation's copper. The objective of this paper is to describe the operations of a small mining company - Ranchers Exploration and Development Corporation - how it views its place in this industry of giants, how it exploits the advantages offered by its relatively small size, and how it protects itself from the hazards being small introduces. Environment is, of course, a critical factor for such a company because it does not have the resources which help large companies weather periods of financial stress. Ideally, this environment is characterized by a heal thy economy, strong product demand, relatively stable prices , adequate grades and tonnages of ore commensurate with depth and over-burden, ready access to utilities, a dependable labor pool, and suitable technical "know how". When the environment is right, properties which were previously uneconomical to operate attract the attention of companies whose primary interest is a return on investment commensurate with risk over a reasonable period of time. Naturally, the amount of the investment and the duration of operation determines the size of the company which would be interested in such a venture. Such is the case with Ranchers Bluebird Mine at Miami, Arizona - a small property operated by a small company in a favorable economic environment.

Jan 1, 1967

Jan 1, 1967

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967

Jan 1, 1967

By J. P. Pritchard, J. T. Pierce, O. G. Slay

This paper discusses the results of a technology-evaluation program to ascertain the feasibility of a piotornask-photoresist technology developed for fabrication of multiple-layer thin-film superconductive circuitry. The uehicle selected for this evaluation was a 120-bil associative data processor requiring a set of nine photomasks to define a similar number of patterned material layers of lead, tin, and polymer insulation. A total circuit area of 4 sq in. involved 2500 actitle and 12,000 passive crossings. Several short-free, electrically continuous specimens were satisfactorily completed under this program. Problems encountered in the preparation and use of the requi-ed set of Photomasks are discussed, as also are the problets of providing suitable external connections. A major retarding factor in the development of the superconducting thin-film cryotron technology for many years was the absence of batch fabrication means yielding necessary device density and count per substrate for practical applications. Early workers in the field desired only limited numbers of devices to permit careful study of discrete devices and representative circuitry integrating logic and memory capabilities. For these purposes mask stencils could be formed to selectively control the placement of materials, sequentially vapor-deposited in vacuum, to form the multilayer structure. In general a distinct pattern was required for each material layer; therefore, mechanical provisions were required to change not only the material source, but the patterning mask as well, before each deposition. All deposition steps were preferably performed in a single evacuation of the deposition chamber. Thus the means for storing, transporting, and registering masks and sources with respect to the substrate existed and were operated within the vacuum environment. In the authors' experience, the approach was and remains serviceable for preliminary device study, but was not extensible to an economical manufacturing method by virtue of the difficulties inherent in mask stencil preparation and use, and the capital investment implicit in the mechanization requirements. Since the commercial attraction of the cryotron technology stems principally from its potential for economical batch fabrication, the authors' program has placed major emphasis on fabrication methods. A highly useful method has evolved through adaptation

Jan 1, 1967

Considerable improvements in diamond drilling equipment have been made since the early 1950s. A recent drilling programme, however, at Williamtown, near Newcastle, carried out by the Joint Coal Board on behalf of the Electricity Commission of New South Wales, emphasized deficiencies in existing equipment when particularly diflkult coring conditions were encountered.Spurred by unacceptably low recoveries in coal seams in this area, the Joint Coal Board devised and developed, with the assistance of the Electricitv Commission, a new typc core lifter and a special 26 ft triple tube core barrel, designed to operate in conjunction with it in bad coring conditions.The core lifter, whieh is propped open clear of incoming core during drilling, is activated by fluid impulses generated inside the core barrel. It can be used with double tube barrels when drilling firm rocks whichdo not change diameter by compaction inside the barrel.Softer rocks. such as clayey types, require the use of a rriple tube barrel.Results from testing carried out to date in difficult areas in New South Wales coalfields have shown that greatly improved results can be obtained with the new equipment. Although developed essentially for coaldrilling, the new core lifter and barrel could be adapted to other fields of diamond drilling. Even in areas where no great coring difficulty is encountered the cost advantage deriving from the greatly inereased life of the core lifter and the adaptor in which it is housed could justify its use.

Jan 1, 1967

Jan 1, 1967

By D. M. Urich

This paper is a follow-up on a previous paper presented at the A.I.M.E. Meeting in Chicago, Illinois, on February 17, 1965, by Mr. D. Kelly Campbell. Mr. Campbell's paper was presented prior to the operation of the Eveleth Taconite-Company's Plant, and this paper outlines and reports on the operation and performance of the Plant after the first nineteen months of operation.

Jan 1, 1967

By S. R. Goodman, Hsun Hu

The formation of secondary - recrystallization tex-tlires in cube-textured 18-8 stain less steel (Type 304) Ilas been studied at three temperatures. Prolonged annealing at 100°'C protluces a PredoninanGly (520) [OOZJ-type texture, which is related to the cube te.ture of the primary lnatrix by a rotation of approxivzately 22 deg around the [001] axis in the rolling direction. Annealing at 1200 or 1300°C facers the formation of the (123)[272/-type texture, which is related to the matrix texture by a [111] rotation of app.voxiniately 40 deg. These observations suggest that in the secondary recrystallization of cube-texlut-ed stainless steel an apparent actilation energy for growth is higher for grains related to the tncrtuix Og [111] rotations thun those reloted by [100] rotations. THE formation of secondary-recrystallization textures in cube-textured primary matrices of fcc metals has been studied widely by various investigators. For Fe-40 pct Ni alloys, Pawlek' and wassermann2 reported that the orientations of secondary grains were related to the cube texture by rotations of 30 and 38 deg around [001] in the rolling direction. However, Rathenau and custers3 found that, while in one Fe-48 pct Ni alloy, most of the secondary grains were oriented with respect to the cube-textured matrix by rotations around [001] of 26.5 deg, in another alloy of a different origin, the orientations of secondary grains were related to the cube texture by rotations of approximately 35 deg around a [lll] axis. Similar orientation relationships were also observed between the secondary grains and the cube-textured primary matrices of copper.4"a No attempt was made to differentiate these two types of orientation relationships; reorientation by either a [111] or a [100] rotation was considered to be equally favored. The present investigation consisted of a study of the secondary recrystallization textures in cube-textured stainless steel. It was noted that the secondary grains formed in stainless steel were considerably smaller than those of Fe-Ni alloys or copper. This offered the advantage that the secondary recrystallization texture could be determined by the texture-goniometer technique, and a more detailed study of the textural development during the course of secondary recrystallization could be made. The effect of annealing temperature on the formation of secondary-recrystallization textures was also investigated. MATERLAL AND METHOD It was shown earlier"-" that a strong cube texture can be obtained in 18-8 stainless steels by rolling at 800°C to produce the copper-type deformation texture, followed by annealing at 800" to 1000°C for recrystallization. To improve the cube texture for the present study, a commercial-grade 18-8 stainless steel (Type 304) was rolled at 800°C first to 5 mm (0.2 in.) thick plates. Three of these plates were then stacked and welded together along the edges into a sandwich assembly. After annealing at 900°C for 20 min: the assembly was finally rolled at 800'C to 90 pct reduction in thickness with reheats and end-for-end reversals after each pass. Only the central strip, which was reduced from 5.0 to 0.50 mm (0.7 in. to 0.020 in.) thick, was used. The chemical composition of the steel in weight percent was as follows: C, 0.06; Mn, 0.38: Cr, 18.71; Ni, 9.56: P, 0.011; S, 0.009; and Si, 0.39. The purpose of rolling the strip in a sandwich assembly was to prevent direct contact between the central strip and the rolls. It was observed earlier" that, when the strip was rolled at 800°C without being enclosed in a sandwich assembly, the cube texture obtained by subsequent annealing at 900" or 1000° C for recrystallization was largely confined to the central section of the strip, while most of the recrystallized grains formed in the surface section of the strip were not cube-textured. This was obviously due to the fact that the actual temperature at the strip surface during rolling, as a result of direct contact between the strip and the cold and massive rolls, was considerably lower than 800°C. By using a sandwich assembly for hot rolling, the cube texture obtained upon subsequent annealing for recrystallization was found to extend through the entire thickness of the strip. After rolling, the central strip was taken from the sandwich assembly. and cut into specimens. Prior to annealing. the specimens were etched to 0.25 mm (0.010 in.) thick. A tube furnace provided with a purified, dry argon atmosphere was used for annealing. Textures were determined by the reflection technique. using a Siemens automatic texture-goniometer and ZrOz-filtered MoKa radiation. With a time constant of 4 sec. the preferred orientation of the secondary grains could be measured satisfactorily by the integrated intensities. Both (111) and (200) reflections were measured, and corresponding pole figures were constructed according to the techniques described previously.10 The agreement between results deduced from these two reflections was excellent. RESULTS AND DISCUSSION Secondary-Recrystallization Texture due to Prolonged Annealing at 1000°C. Fig. 1 shows the primary-recrystallization texture of a specimen annealed at 1000°C for 30 min. A substantial improvement in both sharpness and intensity of the cube texture, owing to the present processing method, can be noted readily by comparing Fig. 1 with similar pole figures shown earlier in Refs. 9 and 11. Secondary recrystallization

Jan 1, 1967

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By Lake H. E.

The request to participate on your theme panel was accepted with some reluctance but indeed as an honor. My subject was outlined to cover 'Energy Resources - both nuclear and conventional' as related to your theme 'Minerals - Treasure Trove of the West'. This is indeed quite an order and I hope you will forgive me for concentrating mainly on the nuclear-uranium portion with brief references only to conventional fuels some of which will be covered in detail later in your conference. In regard to Uranium, I am speaking on the fringe of the area containing half the uranium reserves in your country and no doubt to many who are very conversant with knowledge of these resources. Nevertheless since our two countries have been very closely allied in both nuclear developments and uranium supplies I hope an exchange of information may be mutually beneficial. Concentration on the nuclear fuel resources is I hope understandable as nuclear energy is the coming source of power which will augment the rapid demand in the industrialized countries and provides hope for economic power in many of the more underdeveloped countries. The situation regarding conventional fuel resources is more widely known and their expanding future revolves around production cost reductions, research into diversified uses, plus more assurance of imports from countries less effected by international controversies determining export policies.

Jan 1, 1967

By S. D. Irons

With the passage of recent national and state legislation aimed at tighter regulation of air pollution and smoke control, attention has been focused on a problem which has long confronted the coal industry--the disposal of coal waste with its inadvertent ignition. Even as recent as 1935, a decision from the Allegheny County Court of Common Pleas confirms the stand taken on control of burning coal refuse disposal areas. "The uncontroverted testimony is that there is no feasible method of operating a coal mine without a gob pile on the surface, as no use has ever been found for this troublesome by-product of mining; that every large coal mine has a large gob pile close to its tipple; that sooner or later these piles all ignite through spontaneous combustion; that practically every large mine in Western Pennsylvania has a burning gob pile, and that there is no known means of averting such a fire." 19* As a result of the past "no regulation policy," there are presently on the order of 500 burning refuse banks, of which 213, 142, and 49 are found in West Virginia, Pennsylvania, and Kentucky, respective¬ly. 18 Many of these refuse banks have burned for 40 years or more; many others may continue burning for a like period. It is estimated that the annual emission from these smoldering piles approaches 183,000 tons of pollutents which may produce many deleterious effects on the populace, property and vegetation in the proximity to the sources.16 To date, little progress has been made in alleviating the pollution from the currently burning refuse banks; however, numerous investigators who are researching the causes of ignition, as well as preventative disposal techniques (refuse compaction, layering and crushing to finer sizes) have met with some success in handling the newly discarded coal refuse.

Jan 1, 1967

By N. N. Breyer

A specially built "hard" tensile machine with characteristics permitting the precise detertnination of the drop of the load at the yield point has been used to study the magnitude of the yield-point phenotnenon in prestrained martensitic 4340 steel. A new phenonzenon, the appearance of a secondary yield point, has been observed by holding the specimen at constant strain in the plastic region. Furthermore, it has been found that a series of yield-point drops could be introduced by successive constant strain holds in the plastic region. The isothermal kinetics of the development of the secondary yielding point lave been studied at four temperatures: 24° 0° -18°, and -79°C. From the results of the kinetic investigation, equations for the In a previous investigation1 it was shown that, contrary to generally held opinion, steels of medium carbon content, such as 4340, 4140, and 86B30, in the as-quenched martensitic condition, can be cold-drawn through a die with reductions in area of up to 10 pct without cracking. Tensile specimens of 4340 machined from bars quenched and prestrained in this manner exhibited tensile strengths of about 400,000 psi coupled with 30 pct reductions in area. In addition, it was found that each sample of such steels exhibited a yield point in the quenched, cold-drawn condition. Since these studies were conducted on a commercial hydraulic testing machine of a type which is not well-suited to detailed study of yield-point behavior, it was decided to study this phenomenon more thoroughly on a rigid straining machine. In this new investigation, use of such a "hard" machine not only allowed study of the magnitude of the yield-point drop but also revealed a new phenomenon—secondary yielding of the martensite introduced by stopping crosshead motion after plastic deformation of the sample had begun. The present paper is a report of these findings. MATERIALS AND PROCESSING The material used was a commercial 4340 steel of the composition shown below: 0.41 0.80 0.013 0.019 0.31 0.85 1.76 0.28 1 0.42 0.77 0.015 0.024 0.30 0.84 1.69 0.28 0.08 2 1 = Ladle analysis. 2 = Laboratory analysis. Bars of this steel were processed in the following way: 1) machined to predetermined diameters; 2) austenitized at 870°C for 1 1/2 hr; 3) oil-quenched; 4) cooled to -115°C for 1/2 hr; onset and increase in magnitude of the secondary yielding in this temperature region have been found to fit the relationship ?Ys = Atn where ?Ys is the magnitude of the secondary yield Point in psi, t is the time in seconds, and A and n are parameter characteris-tics of the material. Although the occurrence of the primary and secondary yield points could be rationalized qualitatively on the basis of stress-induced ordering of carbon atoms in the stress fields of dislocations, as postulated in an earlier paper, the kinetics of the secondary-yield-point development were interpreted to indicate that the ordering involves more than just single jumps of carbon atoms from high-energy to neighboring low-energy sites. 5) pickled and lime-coated; 6) drawn through a carbide die. The predetermined diameters were chosen so that drawing through the same die gave the various reductions desired. Tensile specimens of 0.252 in. diam with a 1 1/4 in. gage length were then prepared from the drawn bars and tested. In order to study the stress-strain behavior at the yield point in detail, a rigid tensile machine with a high spring constant was constructed. Columns of large cross section (relative to the specimen cross section) constituted the machine frame. A dc motor was used to drive a screw via a gear reducing train and a "crane" thrust bearing. In this relatively simple device small deformations could be observed un-blurred by the slow response and lower spring constant inherent in hydraulic machines.' A strain-gage dynamometer permitted load changes as small as 8 lb to be read. RESULTS Tensile test samples machined from bars in the as-quenched condition with no subsequent drawing and samples from bars with 3.8 pct reduction after quenching gave stress-strain curves typified by those shown in Figs. I and 2. The time lapse between predrawing and tensile testing varied but usually ranged between 3 to 6 days at room temperature. The strain rate during testing was 0.003 in. per in. per min. The as-quenched curve is seen to have a broad serrated maximum whereas the stress on the specimen prestrained 3.8 pct rose linearly to point A, Fig. 2, fell abruptly to B, and then gradually to C. The abrupt drop to B was accompanied by evidence of incipient necking. The drop of the stress at the yield point in the prestrained samples (A to B in Fig. 2) changed with the percent prestrain, as illustrated on Fig. 3. Although the tensile strength increased continuously with the amount of previous cold drawing, the magnitude of the yield point drop first increased—up to about 6 pct prior reduction—and then decreased. Specimens from bars predrawn more than 8 pct broke in a brittle fashion in the elastic portion of the stress-strain curve.

Jan 1, 1967

By T. M. Korzekwa, R. L. Cavanagh

Following considerable experience with the beneficiation of Wabana iron ore by standard methods, a study was made of the benefits to be obtained by semi-reduction. The basis of the laboratory program was an extensive mineralogical and liberation investigation which guided subsequent work. Partial reduction and beneficiation on a laboratory scale was carried out on lump ore and fines. The reduced ore was magnetically concentrated and the concentrated fines were briquetted. Data are presented on reducibility, sizing vs reduction rate, magnetic cobbing and separation, and the elimination of phosphorus. Past work is reviewed briefly and comments are made on the relation of laboratory to pilot-scale tests.

Jan 1, 1967

By D. D. Bell

This paper presents the history of uranium procurement and demand, and takes a look at future requirements. The three basic conclusions drawn are: (1) the productive capacity of former and existing producers whose operations may be profitably reactivated is insufficient to meet demand projected beyond 1975; (2) reserves in the $5 -$10 price range do not provide the flexibility to sustain production at the high rates required in the late 1970's; and (3) only higher prices can overcome these deficiencies, as this would provide sufficient inducement for the industry to explore for and develop new reserves and productive capacity.

Jan 1, 1967

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967