Search Documents

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By E. G. Davis

Large-scale ultrafine grinding tests of a coarse kaolin were made using the Bureau of Mines developed attrition grinding process in continuous open-and closed-circuit systems. A 20-inch diameter attrition grinder, designed and constructed at the Tuscaloosa Laboratory, was used. Studies included single- and multiple-stage open-circuit grinding, and also continuous grinding tests in closed-circuit with a 6-inch-diameter solid bowl centrifuge. Clay feed, containing 9.0 percent minus-2-micrometer esd, was used at fates up to 840 pounds per hour. Multistage grinding tests gave better results than single-stage treatment when equivalent clay feed rates were used. Closed-circuit grinding tests yielded ground products containing slightly more minus-2-micrometer-esd clay than the open-circuit grinding when using the same clay feed. Energy consumption was lower in closed-circuit grinding than in batch or open-circuit grinding. A modified two-stage closed-circuit grinding system gave the best grade of product and amount of minus -2-micrometer-esd clay produced per pound of clay feed. The ground product from this test contained 88.5 percent minus-2-micrometer-esd material and electrical energy consumption was 327 kilowatt-hours per ton of minus-2-micrometer-esd material produced.

Jan 1, 1973

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By L. J. Douglas, A. G. Kim

Methane and other hydrocarbon gases, byproducts of coalification, are emitted from coal at widely varying rates and often present ventilation problems during mining. The air in some coal mines apparently contains no methane. To determine if coals from mines which had no history of detectable gas emission contained adsorbed methane, samples of coal at the shaft bottom and at an active face were obtained and placed in sealed metal cylinders. The atmosphere around the coal was sampled and analysed by gas chromatography. Methane, ethane, ethylene, propane, propylene, and butane were found to have been desorbed from these coals. Hydrogen and helium were also detected. An estimate of the amount of residual gas per ton of coal indicated that coal samples from the active face generally contained more adsorbed gas than coal samples obtained from the shaft bottom, although in both instances the total amount of gas was relatively small.

Jan 1, 1973

By F. E. Spencer

Calculated equilibrium data are presented for three phases in the flue gas stream from a hypothetical open cycle MHD generator. A typical coal is "burned" with 1.0 gram-mole K2O seed per kilogram coal and with 101 percent of stoichiometric air. Tables of composition and the overt thermodynamic properties, enthalpy and entropy, are given for the temperatures 2200 (-100) 1100 kelvins, pressures 1.0 and 1.5 atmospheres, and slag rejection figures of 90 and 75 percent.

Jan 1, 1973

By C. J. Brown

"Access to the outside world is supplied by the Alaska Highway to continental Canada and the United States, the Haines Highway, and by the White Pass & Yukon Route to Skagway and Vancouver. Communities and mining developments located along the Alaska Highway are supplied daily by truck transport with commodities originating in Whitehorse, Edmonton, and Vancouver.The average payload on the Alaska and Mayo Highway is in the order of 16 to 25 tons and is subject to government regulations. Highway haulage distances to railhead at Whitehorse vary as does the direction. The Clinton Creek asbestos development is located 395 road miles north-west of Whitehorse whereas the United Keno Hill operation is 287 miles to the north. Cassiar Asbestos is located in Northern British Columbia at a distance of 357 miles south-east of railhead at Whitehorse. In order to service these various mines multipurpose highway vehicles have been designed to allow maximum backhaul of petroleum products. The White Pass & Yukon Route was established as an integrated transportation system from 1955 when it became apparent that three non-integrated systems (ship, rail and truck), with the various paper work and rising costs, could not continue to serve the needs of Yukon. Integration became the company policy and a system was developed. A special container ship (Clifford J. Rogers) was designed and built. This was the first specially built container ship in the world. The northern container integrated system was operational in 1955.In 1965 over 8.5 million dollars were spent in upgrading the container facility and the construction of a tanker-container ship designed specifically to serve Yukon and Northern B.C. This program was based largely on experience gained with the original container concept. Two tanker-container ships handled"

Jan 1, 1973

By V. F. Hollister

Although it is apparent that porphyry copper deposits may have formed in the Andean orogen from Permian time onward, commercial deposits thus far developed appear to have Cenozoic ages only. Following Chilean useage, the porphyry deposits are divided into either: (a) a stockwork, or (b) a tourmaline breccia model. Stockwork type deposits tend to occur on major strike-slip structures which may be either transcurrent or transverse faults related to plate movements, while the tourmaline breccia type may more frequently form independently of regional faults. Stockwork types may be conjugate fractures that intersect and ramify as a network of veins and veinlets, cutting altered rock, and genetically related to a major regional fault, or in other cases they may reflect the intersection of two large fault structures. Circular fracture patterns may more rarely occur in stockwork deposits in response to a specific intrusive. Tourmaline breccia types are characterized by circular and radial fractures genetically connected in some way with tourmaline breccia pipe development or an intrusive piercement that preceded it. Each structural model contains mineralized intrusive8 which have a close time-space relationship to ore and in each model, mineral paragenesis is similar, regardless of age or location in the plate. Also, each model contains the same type of alterntion halos (phyllic, argillic, prophllitic) as are developed in intru- sive centers in porphyry copper deposits found in North America. The potassic zone is exposed best in the older deposits. Examples of each type of deposit are illustrated, demonstrating the feature evolved.

Jan 1, 1973

By Joseph Grumer

Reported fiscal year 1973 studies of fires and explosions seek to develop capabilities during mining operations to detect and quench ignitions of gas in the face area, to detect and quench by means of passive or triggered barriers explosions propagating in rock-dusted coal dust, and to detect incipient fires early enough for easy extinguishment. Research discussed includes minimum air velocities to lift coal or rock dusts, surveys to determine adequacy of rock dusting, chemical agents to quench gas or coal dust explosions and their relative efficacies, spectra radiated by explosions, and nozzle sprays of extinguishants.

Jan 1, 1973

The phosphorus content of the banded iron formation (BIF) and of the associated iron ore deposits in the north west of Western Australia is known to vary widely, a fact which has considerable econ~mic significance. Trendall and Blockley (1970) have described the variety of textural appearances of apatite in the Hamersley Group BlF, and suggest that apatite may account for the entire phosphorus content of the unaltered BIF.A preliminary investigation using an M.A.C. electron microprobe analyser has shown that, at least in some iron ores and in partially enriched BIF and associated shales, the phosphorus occurrence is more complicated than this. A suite of samples was examined from one location which covered the entire Dales Gorge Member and some adjoining macrobands in the Mt. McRae shale, together with samples selected for their high phosphorus content, degree of ore enrichment, and position relative to the enrichment zone. Calcium apatite was not observed in any sample of ore from this sequence, despite its ubiquitous occurrence in the BIF. Silicate mineralogy in the enriched regions also differs from that in the BIF, but this change has not yet been studied in detail.The phosphorus content of goethite in one orebody is often high and appears to be in solid solution in the goethite structure. It shows little or no variability on a micro-scale within a grain, except where theremay be a zoned enrichment near boundaries and solution channels. There is also a limited solubility of phosphorus in hematite (the maximum observed by the author is 0·1 per cent P); but where the hematite is martitic (after magnetite) its phosphorus content is always low or zero. In some bands, martitic hematite has been hydrated to goethite, and this also has a very low phosphorus content. Phosphorus was not found in the silica or silicates in the ore, and even when iron enrichment is just beginning, a limited suite of samples from the BIF suggests that the phosphorus content of the chert microbands is almost entirely in the microscopic goethite nuclei (after riebeckite) scattered throughout the chert. The ability of goethite and hematite to accept phosphorus...

Jan 1, 1973

By Theodore H. Eyde

In 1971, the Minerals Division of The Superior Oil Company acquired exploration rights to an unpatented claim group in the Superior (Pioneer), Arizona mining district, lying west of the Concentrator fault. This major post-mineral fault displaces the Magma vein-fault, which is mined in the Magma Mine at Superior, Arizona. The Magma vein-fault and the enclosing section of pre-mineral rocks consisting of Paleozoic and younger Precambrian sediments and diabase, is overlain by a thick section of post-mineral rocks, consisting of the Gila conglomerate, the Apache Leap dacite, and the Whitetail conglomerate. Geologic information on the thickness and attitudes of the rocks obtained from previous diamond drilling indicated that the section of post-mineral rocks might be from 3,000 to over 4,010 feet thick in the target area. (Figure 1) The Magma vein-fault is a steeply dipping vein which has produced nearly a billion dollars of copper, zinc, silver, and gold. It has been mined continuously for nearly 10,000 feet along the strike and nearly 5,000, feet vertically down the dip. It ranges from less than a foot to over 50 feet wide and contains sulfide mineralization con¬sisting of pyrite, chalcopyrite, bornite, and chalcocite.

Jan 1, 1973

By Wright R, Stock E. C

The Windarra nickel deposits known to date comprise two sulphide orebodies located at Mount Windarra and South Windarra. These orebodies, which are 15 km apart, lie within an ultramafic complex at or near its footwall contact with a banded iron formation. The Windarra deposits are 270 km north-northeast of Kalgoorlie in West- ern Australia which was the centre of a major nickel exploration programme fol- lowing the discovery of nickel deposits at Kambalda in 1966. Surface indications of the Mount Windarra orebody were discovered in 1969 by Mr. Ken Shirley while prospect- ing the Laverton area for Poseidon Ltd. (then NL). The mineralisation was loc- ated by systematic prospecting for goss- anous material associated with aero-mag- netic anomalies and ultramafic rocks. The South Windarra deposit was dis- covered in 1971 by the Union-Hanna- Homestake Joint Venture, by exploring along the strike extension of the mount Windarra ultramafic-banded iron format- ion contact. A detailed ground magnet 1. Acting Operations Superintendent, Windarra Nickel Project, Windarra, W.A. 2. Senior Geologist, Windarra Nickel Project, Windarra, W.A. 3. Mine Geologist, Windarra Nickel Project, Windarra, W.A.

Jan 1, 1973

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By Parviz F. Rad

This Bureau of Mines report reviews laboratory and in-mine techniques for determining mechanical properties of coals, with special emphasis on the relationship between these properties and the minability of coal. An extensive bibliography is included.

Jan 1, 1973

By Gerhard Braüner

The report gives a review of the methods of predicting mine subsidence; these methods are used particularly in European coalfields. The methods are subdivided into two groups, based on mathematical expressions either for the trough profile or for the influence of infinitesimal extraction elements. The fundamental relationships common to all methods described herein are the principles of superposition and of equivalent extraction areas. The involved parameters are derived from field observations. For calculating horizontal displacements, their relation to the slope of the subsidence profile is applied. The time-dependent development of the subsidence process is characterized by the empirical "time factor." Modifications for the case of inclined strata are considered. A brief review of experimental and theoretical model investigations is given.

Jan 1, 1973

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By L. K. Barker

The purpose of this research was to determine how much, if any, improvement would be made by subjecting hydrogenated shale-oil naphtha to a catalytic reforming process. Preselected ranges of temperature and pressure within the commercial reforming ranges were chosen for investigation and other possible variables were held constant. All tests were made with a liquid hourly space velocity (LHSV) of 3 volumes of liquid feed per volume of catalyst per hour (Vf/Vc/hr) and a hydrogen feed rate of 3,000 scf/bbl. Operating temperatures of 850°,875°, and 900° F were used at pressures of 200,400, and 600 psig. The greatest octane improvement in the naphtha was obtained at a temperature of 900° F and pressure of 200 psig. The reformed naphtha had a clear research octane number of 89, a liquid yield of 80 vol pct, and a yield-octane number of 71.1. The data indicate that a higher temperature could have produced a higher yield-octane number.

Jan 1, 1973

By Brian F. Osborne

A continuous on-line particle size analysis system for solid/liquid suspensions is described. The basic sensor utilizes a centrifugal principle to separate particles according to size, the resultant separation being measured by means of beta-ray attenuation. Results obtained when analyzing a variety of materials at sizes from 65 mesh (210 microns) to 20 microns are discussed in de- tail. Accuracies better than 2% are demonstrated. The effects of particle specific gravity, and mixtures of materials of diverse specific gravities, are discussed from a practical and theoretical viewpoint. It is demonstrated that particle specific gravity has a minimal effect on the size reading obtained. This renders the instrument suitable for handling materials where the ratio of light to heavy component may change. The design of the first commercial installation of this instrument is described in detail. This installation will be capable of analyzing three streams in sequence, measurement at three particle sizes being effected on each stream.

Jan 1, 1973

By Gerhard Braüner

The present knowledge on ground movements and mining damage is mainly based on observations made when mining seamlike deposits. The studies, rules, and regulations in different countries agree in that the differential ground movements, especially the strain, account for the damage to structures. Accordingly, large buildings are particularly susceptible. The opinions on what amount of ground deformation induces what degree of structural damage are not quite uniform. Mining damage can be reduced or prevented by structural and/or underground precautions. The latter comprise measures for generally reducing the ground movements (leaving pillars, filling, partial extraction) and for reducing temporary movements (rapid extraction, specially arranged workings). Because the differential movements decrease with increasing depth of mining, safety pillars are largely dispensable at greater depths. Shafts are mainly affected by the vertical derivatives of rock displacements, but extraction in the vicinity of shafts is feasible even under difficult conditions. The theoretical concept of the ground movement process established in part 1 of this work is in qualitative agreement with the facts herein observed. As a quantitative approach, it should be applied to calculating ground surface movements rather than rock movements about underground openings. It can be extended by introducing more detailed strata characteristics.

Jan 1, 1973

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By P. G. Lazenby

This paper describes the latest instrumentation improvements in the INPUT Airborne E.M. System, particularly the new electronic signal-processing techniques. Several anomaly examples illustrating these techniques are shown.

Jan 1, 1973