Search Documents

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By William J. Campbell

This analytical method development and evaluation was undertaken by the Bureau of Mines to provide accurate determinations of eight minor elements in low-alloy steels prepared from ferrous scrap. Fluorescent X-ray spectrography was the principal method investigated. Confirming analyses were made by conventional instrumental and chemical methods. All X-ray data were processed by a timesharing computer. No corrections were found necessary for inter-element effects or overlapping spectral lines. Concentrations were calculated from the least-square fit of a linear calibration equation derived from measurements on three sets of standard steels. These studies show that X-ray spectrographic analysis of lathe-finished surfaces provides accurate determinations of aluminum, copper, chromium, manganese, nickel, phosphorus, silicon, and tin.

Jan 1, 1973

By Arthur H. Leigh

Anode mud, the residual material collected from the bottom of the electrolytic cells during the refining of copper is leached, roasted, fire-refined and cast into Dore1 metal anodes. Dore1 metal is a gold-silver-copper alloy containing 80 percent silver. The metal is processed electrolytically using the Moebius system to refine silver and separate gold, platinum and palladium. The Moebius cell cathodes receive a deposit of silver crystals which are melted and cast into 1000 ounce silver bars with 999 Fine minimum purity. Gold mud is collected in fabric bags and cast into gold anodes for further refining in the Wohlwill cells. Wohlwill cells are unique in that gold, the noble metal, can be put into solution electrolytically without the use of aqua regia. Gold is collected on high purity gold foil cathodes and cast into 400 ounce bull ion with 999.7 Fine minimum purity. Platinum and palladium remain in the electrolyte progressively increasing in concentration and are finally separated and purified by precipitation.

Jan 1, 1973

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By Yoon T. Auck, Milton E. Wadsworth

Column leach studies of two low grade prophyry copper ores were made with variables of size, flow rate, pH, drainage rate and tempature. Evidence is presented to show that, in some types of ores, sulfide minerals block leaching channels and regulate the rate of dissolution of gangue constituents. Basic iron sulfates, dissolved by introducing acid, provide oxidizing agent in the form of ferric ion in the absence of oxygen. Ferric ion then acts to release copper from the ore. Oxygen up-take was found to increase with the lowering of the pH and to follow parabolic kinetics attributable to the precipitation of basic iron salts within the pore channels. Slow drainage of residual gravitational water can seriously retard oxygen up-take during oxidation for particles in the coarse sand range. A model is presented for dump leaching in which a reaction zone connected by channels to the surface of the ore particle moves topo-chemically during the course of the reaction.

Jan 1, 1973

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By Arthur R. Still, Paul A. Bailly

5.1-PURPOSE, PROCEDURE, METHODS, MANAGEMENT Exploration can be technologically defined, with regard to the discovery of new mineral deposits, as all the activities and evaluations necessary before an intelligent decision can be made establishing size, initial flowsheet and annual output of new extractive operations. The purpose of mineral exploration is the discovery and acquisition of new mineral deposits amenable to economic extractive operations now or in the future. A prime objective of mineral exploration, however, is to find and acquire a maximum number of such mineral deposits at a minimum cost and within a minimum time. Immediately upon the heels of a successful ''exploration" discovery follow activities called, first, development, then operation. Under U.S. Internal Revenue Code regulations (Secs. 1.615.1 and 1.616.1) in effect at the time of this writing, which state that the "development stage" has been reached when "deposits of ore or other minerals are shown to exist in sufficient quantity and quality to reasonably justify commercial exploitation by the taxpayer," exploration in the technological sense may well continue after a mineral property has entered the "development stage" as defined for tax purposes. In many instances continued exploration, after reaching the tax defined "development stage," has disclosed additional reserves which justify a much larger, more efficient and more profitable operation than that which would constitute the minimum feasible. Even after a mine goes into production, continued ore search generally will increase the reserves, either justifying expansions in plant capacity or prolonging the life of the operation, but this work (actually "exploration") is normally considered, for bookkeeping and tax purposes, a part of mine development. Each exploration entity defines its own objectives in terms of acceptable mini- mum rate of return on investment for any deposit found and retained, and in terms of which commodities, and markets, are to be involved. For these reasons, exploration programs, and aims, will vary over a wide range, although all have the common objective of endeavouring to create new profit centers for the future. 5.1.2-EXPLORATION METHODS Exploration has evolved in the past several decades into a highly sophisticated and expensive endeavor in which large corporate entities, or subsidaries, normally are directed and staffed by highly trained exploration specialists. In some instances consultants, with expertise in a given field, are utilized to the benefit of such corporate groups. The "grasshopper" approach to exploration-searching only for outcropping minerals and/or investigating only mineral prospects offered by the discoverers of such outcrops has given us most of the past and present mines in the US., but this method is rapidly approaching the point of diminishing returns in areas that have been thoroughly prospected for currently marketable commodities. With

Jan 1, 1973

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By C. M. Kleemann

The paper describes the present milling practice at Western Mining Corporation Limited's new nickel mine at Kambalda in Western Australia. It details the crushing, autogenous grinding, flotation and spray drying circuits for the production of a nickel concentrate. It also indicates some of the metallurgical problems which have been encountered in concentrating this ore.

Jan 1, 1973

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By Dalton. J. L., H. P. Dibbs

An account is given of investigations into the application of two neutron methods to the on-line analysis of slurries. One deals with the application of the neutron moisture gauge principle to the determination of the water content of iron oxide slurries, and the other with the application of gamma radiation from thermal-neutron-capture to the determination of the composition of aqueous slurries of iron oxide, copper oxide, zinc oxide and sulphur. Linear relationships were found between the composition of the slurry and the neutron count-rate in the first study, and between the slurry composition and the prompt-gamma-ray count-rate in the second study. A mathematical relationship has also been developed which relates changes in the prompt-gamma-ray counts from hydrogen to changes in slurry composition.

Jan 1, 1973

By Russell F. M

Following the accident in the Peterson section of Mufulira mine in September, 1970, a method had to be found of extracting up to 300 000 tonnes of ore per month from this area without inducing caving. Sandfill mining methods were chosen, necessitating a plant capable of producing both cemented and uncemented fill on a large scale. The paper covers the design and construction of this sandplant which is thought to be unique for its size, as it incorporates three 3 000 tonne capacity settled storage silos, a 500 tonne capacity cement silo, mixing tanks and a control room situated underground. The plant is designed to handle an aver- age of 440 tonnes per hour with a maximum of 660 tonnes per hour for limited periods, delivering either uncemented fill or cemented fill in proportions varying from 1:6 to 1:30. The instrumentation and equipment necessary to give one man operation of the plant is described and the fill mining methods now in use at Mufulira are briefly outlined.

Jan 1, 1973

By Palmer W. T

The successful re-opening of the Cobar min- eral field was dependent upon the success- ful introduction of highly productive, low cost mining. Mechanised cut and fill stop- ing with incline access was selected for the C.S.A. mine because it permitted flexi- bility, complete primary extraction with no secondary pillar recovery, minimised dilu- tion and oxidation, a minimum of pre-pro- duction development and because diesel powered load-haul-dump (L.H.D.) units were proving reliable and highly productive in the U.S.A. Although L.H.D. vehicles are the key to the success of the mining method, four other main groups of vehicles are utilised in the mine - trucks, scaling vehicles, ser- vicing vehicles and specialist vehicles. The operating requirements at the C.S.A. mine are more stringent than those encount- ered in many other underground mining oper- ations. The first L.H.D. vehicle used at Cobar - the Transloader - had considerable difficulty in loading and discharging coarse production ore. The Wagner ST5 Scoop Tram performed this duty much better. However, the first generation Scoop Trams were not robust enough to withstand the heavy duty and many modifications were necessary before acceptable availabilities were obtained. Similar modifications were necessary for the Eimco 916 vehicle but the Eimco 915 unit came much closer to meeting the duty requirements. Eventually Cobar technical personnel design- ed a L.H.D. vehicle to meet specific C.S.A. mine conditions. These units have proven most satisfactory. Over 8 years of operation the underground vehicle fleet has become a proliferation of vehicle types. A standardisation pro- gram has been initiated based upon common prime movers being mated with "trailer" units to serve specific functions. Standardisation will reduce inventory levels and facilitate training of operating and maintenance personnel.

Jan 1, 1973

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By Brian M. Harney

The technique of remote sensing, used for many years by earth scientists, is being applied to the detection and monitoring of air pollution. Instrumentation being developed is of a very diverse nature and is effective, Fn varying degrees, at ranges from 1,000 meters to the altitude of a space satellite. This paper describes a number of the recent developments in this new field. Instruments based on spectroscopic, laser, and photographic systems are discussed. Sensors are being developed which utilize correlation spectrometry, interferometry, Raman scattering, Mie scattering, laser line absorption, and simple photographic detection.

Jan 1, 1973

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By Abdo F. Bayazeed

A survey of the underground injection of steel processing waste pickle liquor (WPL) was made by Bureau of Mines engineers. Hydrochloric and sulfuric acids WPL are being injected into deep wells completed in the Cambrian age Mt. Simon Sandstone Formation in Illinois and Indiana. The Mt. Simon Formation ranges up to 1,800 feet in thickness. The average depth of WPL injection wells is 4,000 feet, and injection is mostly by gravity flow at rates as high as 4,000 barrels per day. The details of the design and operating history of a WPL well located near Gary, Ind., are discussed. Laboratory tests showed that the Mt. Simon Sandstone is sensitive to fresh water. The adsorption of iron and neutralization of acids by sandstone cores from deep wells and an outcrop were determined.

Jan 1, 1973

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973