Search Documents

By Arthur F. Colombo

The selective - deslime - flotation process developed by the Federal Bureau of Mines as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The operating parameters for the selective flocculation - cationic flotation of oxidized taconites from the western Mesabi range in Minnesota are discussed. Data from the operation of a 410 kg/hr (900 lb/hr) pilot plant employing reclaimed water are summarized for 2 types of oxidized taconites.

Jan 1, 1979

By Tyler R. J

Methylene blue dye adsorbs on chalcopyrite concentrates slurried in aqueous solution. Saturation adsorption can be achieved within about 24 hours for dye equilibrium concentrations greater than about 10-5 M. The dsorption coverage is obtained from a measurement of the' colour change of the solution. Comparison with BET measurement of the concentrate surface area shows that 2.4 ± 0.1 µmol of methylene blue are adsorbed per square metre of surface accessible to the dye cation. The procedure described can be used as a single-point measurement and values for the surface area can be otained to within about 10 per cent with inexpensive instrumentation.

Jan 1, 1979

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

"7.1. Glossary of the Platinum-Group Minerals7.1.1. IntroductionA glossary of the platinum-group minerals (POM) serves as a useful introduction to a chapter on their mineralogy. Earlier glossaries (Cabri, 1972, 1976) were prepared for different purposes and composed in a different manner. As for most mineralogical textbooks, from Dana's System of Mineralogy, 3rd Edition (1850) , to Fleischer's Glossary of Mineral Species (1980), this glossary is primarily a chemical classification, arranged here in two tables. Table 7.1 groups the mineralforming compounds of the six platinum-group elements (POE) according to their essential anion(s) or according to the nonPOE element in intermetallic compounds. Table 7.2 is a similar listing for the native metals and alloys of the POE. Both tables include unidentified POM considered to be bona fide new minerals requiring additional study for complete characterization and recognition (see Chapter 9*). Some information on the chemistry of the POM is given in the sections on X-ray data (7 .2) and ore microscopy (7 .3). Because the overwhelming majority of POM have been characterized by the electron microprobe, a more detailed account of representative analyses is given in Chapter 8**. The total POM listed in Tables 7.1 and 7.2 is about 100, after deleting some which would not qualify as discrete species if found today, but which are still recognized on historical grounds; e.g. iridosmine, osmiridium, platiniridium. Tables 7.1 and 7.2 also include 28 unnamed POM; included because they are considered to be probably new species (Cabri 1981 b). The referral scheme for unnamed minerals is the same as in Chapter 9. There are considerably more palladium minerals known than other POM; the proportion of total species (listed in Tables 7.1 and 7 .2) for the POE is: Pd 48%, Pt 21 o/o , Ru and Ir 9% each, Rh 8% and Os 5%. These proportions are in marked contrast to the estimated cosmic abundance, as compiled for average type C1 chondrite by Naldrett and Duke (1980): Pt 29%, Ru 20%, Pd, Ir and Os 15% each, and Rh 6%."

Jan 1, 1979

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By J. B. Stephenson

The Bureau of Mines, under an interagency agreement with the Department of Energy (DOE), investigated the feasibility of hardfacing the critical surfaces of valves and similar devices by chemical vapor deposition. The purpose of this research was to increase the wear resistance of these components for use in the abrasive and erosive environment of coal gasification units. Tungsten and molybdenum coatings were produced on nickel-plated carbon steels and stain-less steels by hydrogen reduction of the metal hexafluoride at 325° to 600° C. Titanium nitride coatings were produced on low-carbon steels by the reaction of titanium tetrachloride, hydrogen, and nitrogen at 1,000° C. Titanium carbonitride coatings were produced on low-carbon steels by the reaction of nitrogen, hydrogen, and methane at 900° C. Tungsten, molybdenum and titanium nitride coatings were formed on 6-, 10-, and l2-inch (0.15-, 0.25-, and 0.30-meter) ball valve seats for evaluation in the low-Btu coal gasification pilot plant at the Morgantown Energy Research Center, Morgantown, W. Va.

Jan 1, 1979

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By L. H. E. Weyher

A mine is essentially a vast materials-handling system. All other systems found in the mine exist to one degree or another to support the materials-handling functions, from the cutting at the face to the hoisting in the shaft. In this chapter computerized planning of underground materials-handling systems will be examined by dividing this function into: (1) the planning of the production section, and (2) the planning of underground rail or belt haulage from the production section to the shaft, slope, or surface. While alternative divisions might focus on the different materials- handling functions, i.e., production, supply, and manpower transportation, historical computer analysis has focused on the various systems rather than functions. The emphasis in this chapter is directed toward coal mine applications; however, most of the programs and methods are equally applicable to other underground mines. Markedly different methods are encountered in each system, and moreover, marked differences exist in the nature and the degree to which the materials-handling subsystems in each interact with the environmental or support systems. The most intimate interaction exists at the faces where geologic, human, and machine performance factors are closely related and constantly varying. In view of this, the planning of the materials-handling systems for the face will usually stress flexibility, while the outby materials-handling systems will generally place decreasing emphasis on flexibility and more on system reliability, capacity, and cost effectiveness. Thus, hoisting and main haulage systems are generally designed and constructed as permanent installations and cannot be readily changed, whereas secondary haulage systems and face operations are relatively mobile. These differences may have considerable significance for the mine planner in making technical and financial comparisons of alternatives to provide the scheduled mine production.

Jan 1, 1979

By P. A. Korpi

The angular spiral lining system reduces energy consumption and grinding media consumption in grate discharge ball mills. This paper discusses the effect of this lining system on mill product size distribution. Performance comparisons of a grinding circuit outfitted with angular spiral liners in the ball mills are made with respect to standard double-wave liner installations. The angular spiral lining system was developed by Waagner-Biro of Austria. The installation of this lining system at Magma Copper Company, San Manuel, Arizona, is the first of its kind in a grate discharge ball mill used for wet grinding.

Jan 1, 1979

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By R. M. G. S. Berezowsky

An atmospheric ammoniacal thiosulphate leach system was developed to recover gold and silver from residues of the ammoniacal oxidation leaching of sulphidic copper concentrates. Extractions of 88 - 95% Au and 83 - 98% Ag were attained within 2 to 4 hours at 40 - 60°C in thiosulphate leaching of the oxidation leach residues of Manitoba chalcopyrite concentrates analyzing 24.6% Cu, 0.18 oz/ton Au and 4.26 oz/ton Ag and a complex British Columbia chalcopyrite/tetrahedrite concentrate analyzing 18.5% Cu, 0.27 oz/ton Au and 276 oz/ton Ag. Parameters affecting the Au and Ag solubilization included thiosulphate, ammonia, and cupric ion concentrations, temperature, retention time and the degree of Cu extraction and sulphide oxidation in the primary oxidation leach. The precious metals were recovered from the thiosulphate liquors by zinc dust cementation.

Jan 1, 1979

By Donald L. Everhart

The National Uranium Resource Evaluation (NURE) program since 1974 has been designed to accomplish a comprehensive coverage of the 48 conterminous States and Alaska to evaluate the total uranium resources of the USA. This resource base includes both ore reserves and potential resources. Techniques include airborne radiometric and magnetic surveys, by hydrogeochemical surveys, surface and subsurface geologic studies, and the application of improved geochemical exploration and resource assessment methods (Table 1). In brief review, the current status of each of the five basic NURE elements is as follows: In the Aerial Surveys, in the conterminous 48 states, the flying has been completed in 89 of the NTMS 10 x 2° NURE quadrangles, and is in progress in 39 more (Figure 1). Complete quadrangle data have already been open filed for 46 additional quadrangles, for a total of 174 for which data gathering is either complete or in progress. In Alaska, the flying is complete in 42 quadrangles, and quadrangle data have been open filed for 34 more, for a total of 76 (Figure 2).

Jan 1, 1979

By Stewart W. J

The volumetric method of estimating hydrocarbon resources and recoverable reserves is and probably will remain a dominant method in petroleum engineering. The method is technically very simple, but has one main problem: how to express, measure and properly handle the variable and complex uncertainty of each estimate. The computer age brought in the Monte Carlo Simulation method which enables correct arithmetic operation using data with specified probability distribution. However, several problems are still not solved uniquely and still exist. For instance, the determination and description of the distribution of single parameters, the determination of the degree of dependency between parameters (e.g. hydrocarbon saturation-porosity), and standard probabilist- ic definition of generally used categories (e.g. proved, probable, possible). Methods for handling these problems are discussed.

Jan 1, 1979

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

The mercury, gold, silver, copper, lead and zinc values of soils over altered and mineralised rock were determined to establish the potential use of mercury as an indicator element in geochemical prospecting. The results are presented to show that mercury can be used successfully in prospecting for precious metal mineralization in the Thames-Waihi area.

Jan 1, 1979

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By Ricardo Gomez, C. T. Ogryzlo, A. A. Dor

This paper reviews the historical background leading to the development of the project. It gives a description of the exploration program and resulting geological and ore reserve information together with plans for mining. A discussion is included of the three processes investigated for the project: 1. Rotary Hearth and Magnetic Concentration 2. Shaft Furnace and Electric Furnace 3. Rotary Kiln and Electric Furnace Results of pilot plant campaigns conducted at Fiskaa, Norway, and Riddle, Oregon, on the process chosen for the production of ferronickel are presented. The paper continues with a review of the considerations involved in selection of commercial plant equipment and concludes with comments on the current status of the project.

Jan 1, 1979