Search Documents

By Young C. Kim

Use of geostatistics to solve mining problems is gaining importance as the cost of developing new mines is increasing and there is a need to mine more marginal deposits. But, until recently, coal companies have shown little or no interest in geostatistics. However, the stringent quality controls on coal burning has led to a surge in interest in improved methods for estimating clean coal characteristics. Until now, most of the geostatistical applications have centered on the problems of estimating in-situ coal characteristics (Sabourin, 1975; Wood, 1976, 1979; Fang and Stark, 1976; Pauncz and Nixon, 1979; and Knudsen et al., 1980). Little work has been done in applying geostatistics to coal washability, except that by Armstrong (1980). Applying geostatistics to coal washability basically means the estimation of cleaned coal characteristics, with the aid of geostatistics. Cleaned coal estimation plays a very important role in overall emission control strategy, as can be seen by the general flow diagram of such a strategy shown in Figure 1. The scope of this paper is limited to one aspect of the overall emission control strategy shown in Figure 1; namely, the prediction of cleaned coal characteristics using geostatistics.

Jan 1, 1982

By T. Kawashima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service port construction, transshipment and environmental control. The major problem is the transshipment of coal. Customary methods for bulk transfer must be improved and/or new systems developed. Slurry unloading has a key role in the new systems. The present report reviews progress in slurry transportation research which has been done in Japan since the 1960s when large scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are discussed.

Jan 1, 1982

By Dale Scott

"The Aggregate Resources Inventory Program was initiated 10 produce reports which assess the aggregate resources of municipalities designated under the Pits and Quarries Control ACI, 1971.Each report consists of three copies accompanied by a text. The text describes the local mineral aggregate resources, extractive activity and characteristics of the ""Selected Deposits"". The first map shows the known sand and gravel resources and their quality. The second map indicates selected sand and gravel resources of primary, secondary and tertiary significance. The third map indicates both bedrock resources and bedrock areas suitable f or extraction. These maps and the text are prepared in a formal suited for use by planning personnel.Recently, the Aggregate Resources Inventory Program has undergone evolutionary changes. New sources of data are being utilized in the inventory reports; in particular, detailed field assessment by inspecting, sampling, drilling and backhoe pitting. Liaison and joint assessment with district and regional Mineral Resources staff of the Ministry of Natural Resources, and personnel of the Ministry of Transportation and Communications, are key components of the Program.Twenty-two reports were available to the public as of December 1980, with a further thirty-six awaiting publication. Our present production rate is 3.5 reports per month. The reports appear to be well accepted by the municipalities and have proven effective in conserving prime aggregate resource areas.IntroductionThe urbanization of Southern Ontario has resulted in a major increase in the production of industrial minerals, such as sand, gravel, clay, shale, gypsum and stone, for use as cru shed aggregate, building stone, lime and cement.Although mineral aggregate deposits are plentiful in Southern Ontario, they are fixed-location, non-renewable resources. The potential for extractive development is usually greatest in urban fringe areas where land-use competition is extreme. Comprehensive planning and resource management strategies are required to make the best use of available resources, especially in those areas experiencing rapid development. Such strategies must be based on a sound knowledge of the total mineral aggregate resource base at both local and regional levels."

Jan 1, 1982

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By William P. Lorenz

Overlying the sulfide mineralization at Anamax Mining Company's Twin Buttes Mine is an oxidized zone up to one hundred meters in thickness. The principal copper minerals in this zone are chryso-colla, tenorite, cuprite, native copper and copper-manganese-iron wad. This ox¬idized zone also contains minor amounts of uranium ranging in concentration from 0.002 to 0.010 percent. Since pit development through 1980, some 38 million tonnes of oxide ore with copper contents greater than 0.6 percent have been brought to the surface. Copper in the oxide ore is extracted at Twin Buttes in, an agitated sulfuric acid leach plant followed by solvent extraction and electrowinning producing 90 tonnes per day of copper cathode. During leaching of the oxide ores small amounts of uranium are solubilized along with the copper values. This is not limited to Twin Buttes as most acidic copper bearing leach solutions throughout the southwestern United States contain small amounts of uranium.1

Jan 1, 1982

By Bujtor G. J, McMahon D. W

This guide to the understanding of ore reserve estimation is the revised version of a report with a similar title circulated within the CRA Limited (CRA) group of companies in mid-1980. It is the principal result to date of an Ore Reserve Study commissioned by CRA in late 1977.This guide to the understanding of ore reserve estimationis the revised version of a report with a similar titlecirculated within the CRA Limited (CRA) group ofcompanies in mid-1980. It is the principal result to dateof an Ore Reserve Study commissioned by CRA in late1977.The study was prompted by two ore reserve situations.The Zinc Corporation and New Broken Hill Consolidated,Broken Hill, had reached the point of havingto find a replacement 'for their traditional ore reserveprocedure and Mary Kathleen had to admit publicly thatore reserve predictions would not be realized. Thesewere not however the only problems to be looked at. Asmentioned more fully later, other ore reserve situationswere known, or were met during the study, in copper,gold and nickel as well, where poor realization: expectationratios had ranged from embarrassing to disastrous.These made it clear that ore reserve estimation had to belooked at afresh.The fresh look has resulted in a broadening of theconcept of ore reserve estimation from its traditionalpurely computational basis to an approach embracingall the many things that can affect expectation andrealization as essential factors. Hence this guiderepresents a gathering together of what has been learnedand what should be known to all those concerned withore reserves in any of its diverse aspects.The study has been marked"by a number of changesof thinking. At first the aspects that appeared to requireattention were two; recognition that an ore reserve statementwas an estimate, not a precise calculation; and asearch for im improved estimation procedure adapted tolow grade ores with narrow economic margins. Threeyears later the view was that the need was to incorporateinto ore reserve estimation all relevant aspects of theproposed mining operation from choice of a samplingmethod to sales contract specifications.This study is thought to be unique in being frankabout weaknesses in ore reserve estimation and intreating failures not as natural disasters (like drought orflood, which have to be endured) but as potentiallyavoidable. It has led to three principal conclusions.

Jan 1, 1982

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

This paper discusses some topical issues on the mining administration and legislation fields including:  1. Licensing û Administration and associated specialist functions including:Processing and volumes of mining privilege applicationsFuture organisation and possible decentralisationSpecialist staffFacilitiesGuide to the Mining Act 1971 2. Mining Amendment Act 1981 Transitional procedures 3. Planning Tribunal First hearing of objectionsPoints of principle resulted there from 4. Quarries and Tunnels Bill Currently before Parliament û implications for metallurgical mining

Jan 1, 1982

US 4,190,434 - In the thermal production of magnesium metal, a mixture of calcined dolomite, an iron- silicon-aluminum alloy as a reductant, and residual slag from the production of ferrochromium is smelted to evolve magnesium vapor, which is then condensed. The use of bauxite is lessened or eliminated because of the relatively high alumina content of the residual slag. R. Bonfils, A. Mena, C. Payn, and L. Septier, assigned to Ste. Francaise d’Electrometallurgie (SOFREM). Feb. 26, 1980. 6 pp. (75-10R). Filed: 6-14-78 (915,387). Priority: France, 6-24-77 (77/20,227).

Jan 1, 1982

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By V. J. McSweeney

This paper is directed at interested parties outside the Beach Sand Industry : the scope is quite broad. The geomorphology described is a successful working hypothesis which guided the author during prospecting and pegging campaigns : the author is not an expert in this field. The test data used in the text, for illustrative purposes, is original and may constitute a contribution to the state of the art. The operation- al and design philosophy embodied in the text is personal and describes the author's methods : all practising exponents would differ in some degree amongst themselves on these subjects. In this paper, no criticism of any existing operation or brand of equipment is intended and names are used to maintain a real contact with the subject matter. The author believes that the operational and design techniques evolved in the Beach Sand Industry under continual duress, have a wider application in the mining industry. This glimpse of the Industry is intended to enhance the respect for the present and past members. Space does not permit individual acknowledgements.

Jan 1, 1982

By B. J. K. Sullivan, Brian Hornsby

INTRODUCTION Mount Isa Mines Ltd. operates a copper and silver- lead-zinc property at Mount Isa in northwest Queens- land, Australia. Mount Isa is located in the tropics at latitude 20°43'S and longitude 139°30’E (Fig. 1). It is on the upper watershed of the Leichhardt River and at an elevation of 365 m above sea level. The average rain- fall is 360 mm/y, the greater part of which falls in January to March (the hot summer months). The mean summer temperature for these months is 30°C (dry bulb), with a maximum temperature of 43°C; the mean wet bulb temperature is 25°C with a maximum of 28°C. Mount Isa is located geologically towards the western edge of the Precambrian Shield of northwestern Queensland. This complex forms a north-tilting dissected peneplain which extends in the north-south direction for 640 km, with widths varying from 32 km to 190 km. The combination of differential erosion, regional strike, and steep dips has produced a corrugated topography of low north-south orientated hills and valleys. The field was first discovered in 1923 as a silver- lead-zinc field. Mount Isa Mines Ltd. was formed the following year and subsequently became the sole operating company on the field. Lead and copper ore have been mined and treated separately and simultaneously at Mount Isa since 1953. Intensive exploration commenced in 1954 and an active exploration program provided the justification for a series of production expansion programs in both silver- lead-zinc and copper (see Table 1 ). The most recent and largest production expansion program at Mount Isa commenced when a decision was reached in December 1969 calling for an increase in copper production from 100 000 to 150 000 t/y of blister copper. A major factor which influenced this decision was the substantial additions to the ore reserves in the so-called 1100 ore body which is a massive copper sulfide ore body with a known strike length of approximately 2500 m, a height which is variable up to 300 m, and a width of generally 300 m up to a maximum of 370 m (see Figs. 2 and 3). Host to the copper mineralization is a complex and variable rock generally called "silica dolomite." The ore body strikes 6.02 to 6.1 rad (345° to 350°), dips west between 0.78 and 1.13 rad (45° and 65°), and is truncated at depth by fault implaced basement rocks. It first occurs some 600 m below the surface and bottoms at about 1000 m below the surface. The unconfined compressive strength of the silica dolomite ore varies from 150 to 250 MPa, whereas the basement rocks, carbonaceous mylonite, slaty shale, buck quartz, and greenstone (a chloritic schist) are considerably weaker, varying in strength from 20 to 80 MPa. The distribution of mineralization within the ore body is variable, but can be considered as generally high grade at or just above the basement contact and diminishing towards the upper reaches of the ore body. The current

Jan 1, 1982

By Alan Rhodes

This study is initiated to investigate the efficiency of separation of mineral slimes using electroflotation as compared to that of column and conventional flotation techniques. Important parameters such as collector concentration, pH, current density, aeration rate, etc., have been studied. The results indicate that electroflotation can be used more efficiently in processing rutile slimes (10 µ) under certain operating conditions.

Jan 1, 1982

By J. J. Pavlica

Grinding in steel mills adversely affects the flotation removal of pyrrhotite from magnetite ores. To elucidate the effect of grinding media on the floatability of pyrrhotite, rest potential and short-circuit current measurements were made on electrode combinations of pyrrhotite-mild steel and pyrrhotite-stainless steel. Galvanic contact of pyrrhotite with mild steel increased the rate of surface reactions on pyrrhotite in air-exposed and oxygenated solutions. It was postulated that the formation of ' an iron hydroxide coating on the pyrrhotite adversely affected its floatability. Its formation was minimal when pyrrhotite was contacted with stainless steel. Fine magnetite particles caused slime coating on pyrrhotite surfaces by magnetic interaction and impaired the flotation of pyrrhotite.

Jan 1, 1982

Used in conjunction with geology and geophysics, geochemistry provides powerful exploration tools of special relevance to Australian environments. New methods are needed that will confront the forthcoming emphasis on locating concealed orebodies. Deep weathering is conducive to techniques using groundwaters or gaseous emanations as sample media. Increasing use is anticipated for isotope measurements and for recognition of country rock characteristics that denote proximity to mineralization. Improvements in the sensitivity, reliability and portability of analytical instruments will underpin the contributions of geochemical methods to future mineral exploration.

Jan 1, 1982

By M. L. Jeremic

"The syngenetic and epigenetic mechanics of sedimentation and deformation of coal seams resulted in various types of internal structure, as listed below:TYPE I-massive structure with evenly distributed coal constituencies of integrated mechanical properties.TYPE II-broad-banded structure, with bright and dull coal bands of differential mechanical properties.TYPE III-heterogeneous structure, with sheared coal bands and partings of sectional mechanical properties.TYPE IV-contortional structure, with refolded coal layers and deteriorated mechanical properties.TYPE V-porous structure of orogenically crushed and pulverized coal, with disintegrated mechanical properties.The study suggests criteria for the estimation of coal seam internal structure (gamma-gamma density log and cracks density log), which might be related to the evaluation of strata stability and coal mineability.IntroductionIt is common knowledge that coal seams have various internal structures due to different syngenetic and epigenetic events. Investigations of the internal structure of coal seams have been carried out in the coal fields of Western Canada, as follows: geological field studies of coal-bearing strata;?,geophysical borehole surveying studies;?,geological borehole logging and crack density;?,underground phenomenological studies of mine structure;?,chemical coal analysis; and?,mechanical testing of coal samples.These investigations eliminated a large number of criteria previously established for the estimation of coal seam internal structure and indicated that, from an engineering point of view, only two of them are sufficient:(I) density of seam profile (inferred from gamma-gamma log);(2) density of crack s (inferred from geological log).On the basis of these criteria, five main structural types of coal seams have been classified, which might be related to mechanics of deformation and ' failure of mine structures."

Jan 1, 1982

By T. Takamori

This paper reviews the present status of coal preparation in Japan concentrating on the process in coal cleaning and waste water treatment. This paper also discusses recent topics on maintenance, automatic control, raw coal management, etc.

Jan 1, 1982

By David B. Gladwin

Regional characteristics in the coal resource base have resulted in application of different mining methods across Canada. Longwall methods predominate in eastern Canada, whereas open pit, hydraulic and room-and-pillar methods are utilized in the west. Both provincial and federal agencies have regulatory responsibilities and both also share in the development of R&D programs. This paper outlines the scale and scope of the various agencies involved with health and safety R&D in our expanding coal mining industry. Specific R&D activities in ventilation, dust control, explosion hazards, tunnel boring, strata control and truck braking, which form part of the national program, are outlined.

Jan 1, 1982

By Byron R. Berger

Epithermal Ag-Au deposits form at low to moderate temperatures in near-surface environments. Historically, these deposits have been the source of high-grade ores. Increases in the market prices for gold and silver make lower-grade ores economically viable when available in large tonnages. Both the high-grade and bulk-tonnage ores are a consequence of the same processes, and general models of epithermal systems can be useful in the search for new precious-metal resources. A detailed study of deposits at Round Mountain, Nevada; Balei, Russia; Creede, Colorado; Guanajuato, Mexico; and Chanarcillo, Chile, indicates that the hydrodynamics of the fluid systems as determined by fracture geometries, the permeability, and composition of the host rocks are the key factors in the creation of both high-grade and bulk-tonnage epithermal deposits. End-member models that explain the range of observed deposit characteristics are: (1) the hot-springs deposition model; (2) the stacked-cell convection model (where mineral deposition occurs laterally along the interface of two partially separated fluid reservoirs); and, (3) the closed-cell convection model (where deposition occurs in vertical zones due to the relatively unimpeded vertical flow of hydrothermal fluids). Boiling and fluid mixing appear to be agents of precious-metal deposition with the self-sealing of the hydrothermal system being an important adjunct to boiling. Imaginative application of model concepts in exploration has led and can lead to the discovery of new high-grade and/or bulk-tonnage precious-metal deposits.

Jan 1, 1982