Search Documents

By Thomas J. Peters

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 15,600 acre (6,310 ha) Freel Peak RARE II area (No. 5271) in the Lake Tahoe Management Unit. This study by the Bureau of Mines indicates that potential for economic mineral resources in the area is slight. The only mineralized structures in the area consists of two quartz veins. One quartz vein, at the Mountain Top Mine (fig. 1), located by Fred Denner in 1932, is estimated to contain 2,000 tons (1,800 t) of silver and copper-bearing resources. Chip samples from the vein averaged 0.61 oz silver per ton (20.91 g/t), and 1.59 percent copper. The narrow vein is not economically mineable. The other quartz vein is poorly exposed and contains traces of molybdenum. A second reported molybdenum occurrence could not be substantiated.

Jan 1, 1982

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

The range of environments which control the level of ground support required vary greatly in terms of rock type, rock structure and the mining method used. At the operating mines visited during this review the level of ground support was such that incidence of rock-fall- related accidents were rare. It was also found that methods existed to support most of the conditions encountered. The main problem areas were weak rock, major geological structures, areas of heavy jointing, high development density and areas affected by high mining-induced stresses and blasting. With stope support the level of success was much lower than that achieved in development; the larger spans and more rapid changes in geometry of open stopes compared with cut and fill stoping (where cables were originally used) led to significant problems. Before a useable design method for cable support of stope walls and pillars can be obtained the precise failure mode of the walls and pillars, and the interaction of the support and the rock mass must be investigated.

Jan 1, 1982

By Ray W. Ballmer

"For his leadership in developing and managing large, complex, and technically innovative mines, particularly the outstanding and successful Bougainville mine and for his lecture, 'The Moving Targets of Mine Development '. " Recipient of the 1981 D. C. Jackling Award

Jan 1, 1982

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By Nicholas T. Zilka

Mineral resource studies by the Bureau of Mines indicate three areas within the Selway Bitterroot Wilderness have mineral resource potential. Regional studies suggest that a granitic stock on the south side of the Wilderness has high potential for a Climax-type stockwork molybdenum deposit (pl. 1, no. 8); but detailed surface investigations failed to recognize a deposit. The Elk Summit area on the north side of the Wilderness contains subeconomic resources of columbium (niobium)-bearing ilmenite in placers (p1. 1, no. 19). Subeconomic silver-copper-lead resources occur in a vein on the northeast side of the Wilderness at the Clift Mine (pl. 1, no. 2-5). The study area has no known deposits of oil and Haas, coal, geothermal resources, or other energy-related commodities.

Jan 1, 1982

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

By Frederick Carr

1. The application of retreat longwall mining to the North American coal mining conditions is be¬coming more advantageous as more experience is gained. The productivity results being achieved and potential possible illustrates that this system can be the keystone of future underground coal production. 2. In the American coal fields multi-entry is normally practiced as this allows profitable longwall development with existing equipment and systems. Difficulties are being experienced however in the longwall retreat phase by the col¬lapse of multi-entry roadways and excessive use of supplemental support in the following panel tailgates. In some instances the headgate of an operating face can also be in difficulty. 3. Jim Walter Resources Mining Division is developed on a mining plan that calls for three retreat longwalls at each of its four deep mines which have varying depths of cover and immediate roof and floor conditions. The #3 Mine has experienced longwall entry difficulty and there were differing viewpoints with respect to the best development systems to adopt particularly regarding the number of entries and pillar sizes. In an attempt to reconcile these different points of view J.W.R. asked Dr. Wilson to examine the problem and this paper outlines the new approach developed.

Jan 1, 1982

By Fumio Wada

Kuroko deposit is a stratabound massive sulphide and sulphate deposit associated with Miocene submarine volcanics and has been considered to be a prototype of meta- morphosed Palaeozoic and Precambrian equivalents. Since the discovery of Uchinotai deposit of the Kosaka mine in 1959, Dowa and other mining companies have conducted intensive exploration work in the Hokuroku district of northeastern Japan. Dowa has been placing its first priority on the exploration of Kuroko deposits and made a series of remarkable successes in finding the Kuroko deposits, i.e. Uchinotai, 1959; Matsumine, 1963; Uwamiki, 1966; Fukazawa, 1969 and Ezuri, 1975. It is emphasized that our successes have resulted from the proper application of exploration technologies accumulated through our experiences. Firstly we defined the Kuroko horizon and favourable felsic volcanism based on the detailed structural and volczno-stratigraphic study of the Hokuroku district, and then delineated the promising areas by means of the quantitative evaluation of geophysical, geochemical and mineralogical parameters such as the magnetic susceptibility and contents of alkaline and alkaline earth metals in the foot wall dacites and clay mineral assemblages of both hanging and foot wall pyroclastics and dacites. Practical application of these techniques is essential to our routine Kuroko exploration.

Jan 1, 1982

By George K. Schenck

This Bureau of Mines publication describes and evaluates a Standard Industrial Classification (SIC) based end-use data system for minerals that is designed to link the demand for minerals to economic activity in commercial uses. The new data system is two-dimensional. The first dimension of technical product classes (TPC's) measures the consumption of minerals in major primary intermediate products. The second dimension measures the consumption of these TPC's in SIC end-use sectors in sufficient detail to identify the major determinants of demand for each TPC. Intercomodity comparisons are achieved at the level of SIC two-digit major groups. The methodology was developed so that all available sources of information from Government and industry can be utilized at minimum cost. This information will be supplemented with additional data to be obtained by modifying existing Bureau of Mines canvasses so as to elicit additional quantitative responses from mineral producers. The new data system is expected to improve significantly the ability to forecast demand for minerals, and provide an information base that would, for the first time ever, permit resolution of such questions as trends in substitution among materials and the intensity-of-use of materials in end-use sectors. For the 42 TPC?s identified in the report, data are available for the new system from current sources or, except for three TPC?s that require new canvasses, can be obtained by modification of existing Bureau canvasses.

Jan 1, 1982

By Douglas W. Huber

During the past decade, a general awareness of the need for and subsequent development of increased safety in United States coal mines has taken place. Government and industry alike were stimulated into accelerating their actions through unacceptable accident statistics and costs (in terms of human misery dollar values). Those of us who work in the United States coal industry are aware of the development of governmental controls on nine safety. Both Federal and State regulations have placed increased responsibility upon mine owners and operators to insure a safe working environment and to provide training for miners. No other industrial group of workers has received such attention or, in our opinion, deserves it more.

Jan 1, 1982

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By Pablo Velasco

After becoming an oil exporter in 1972, Ecuador experienced a remarkable economic upswing until 1978. However, in 1979 and 1980, a combination of only slight improvements in agricultural output and stagnating petroleum output lowered rates of real gross domestic product (GDP) expansion to 5.3% and 4.3%, respectively. In current prices, the GDP in 1980 was estimated at $11.3 billion.2 The slowdown in growth is attributable in large part to the low level of petroleum exploration in the 1972-79 period. Ecuador's production of petroleum declined 4.5% in 1980 compared with that of 1979. The consortium of Corporación Eatetal Petrolera Ecuatoriana (CEPS), the State oil company, and Texaco, Inc., operating in Ecuador's eastern jungle region was responsible for nearly all of 1980 production, The volume of total crude petroleum exports from Ecuador dropped from 44.7 million barrels in 1979 to 40 million barrels in 1980, although crude petroleum export revenues rose from $1,032 million in 1979 to $1,294 million in 1980- The latter figure represented 54% of Ecuador's 1980 merchandise exports. Crude oil exports accounted far about 46% of the value of 1979 merchandise exports. The total nonfuel mineral exports in 1980 were valued at less than $1 million.

Jan 1, 1982

By Kadri Dagdelen

Design of the ultimate pit limit to direct long range mine planning has been a celebrated problem in the mining industry, and in mining academia, since 1965. Although many papers have been presented on this topic, even today, there is not a single solution technique which is widely accepted and considered universally best. Many philosophical differences exist among the pit planners concerning the use of different methods and it appears that resistance is very strong towards accepting other techniques if you are a believer in one. Whatever the case might be, the pit parameterization technique for the ultimate pit limit design is the latest and takes a different approach than its predecessors. There are already a number of papers which discuss the concepts involved (Francois-Bongarcon, 1976; 1978; 1980; 1981); however, the aim of this paper is to fill in some of the gaps which are thought to be missing in the previous discussions and, in addition, to present the recent research done on the subject at the Centre de Geostatistique de l?Ecole de Mines de Paris in Fontainbleau, France. This paper is divided into two parts. The first part will discuss practical aspects and interpretations of pit parameterization concepts with- out using mathematical or theoretical arguments; the reader who is interested in the theory should refer to Francois-Bongarcon (1978). The second part will present an approach to obtain a complete double parameterization of reserves using an inexpensive (computer costs) single parameterization algorithm. A case study of this approach is also included.

Jan 1, 1982

By C. R. Edwards, J. R. Smith

"INTRODUCTIONThe purpose of this paper is to give an overview of the ALSANDS PROJECT, with emphasis on the approach taken in the design of the Primary Extraction and Froth Treatment Plants.The Alsands Consortium (Table 1) is a Joint Venture of 9 companies formed in 1978, with its prime objective to obtain governmental approval and concomitant suitable commercial terms to build and operate a third oil sands mining and upgrading facility in the Athabasca Oil Sands Deposit.Alsands Energy Limited is the Consortium Manager.The Alsands Project will provide about 10 percent of Canada's forecast crude oil production by 1990, which will be 20,700 cubic metres per day (130,000 barrels/day) of synthetic crude oil plus 1,100 cubic metres per day (7,000 barrels/day) of liquid petroleum gases. To construct Alsands the time required by construction labour, field non-manual and engineering support personnel as well as those trades involved in project-related urban development will total approximately 100,000,000 manhours or 50,000 man years. During regular operations, 4,800 people will be employed by Alsands.Approximately $13 billion will be spent to design, construct and start up the plant by the scheduled 1988 completion date."

Jan 1, 1982