Search Documents

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By Andrew M. Leszcykowski

This report represents the first comprehensive accounting of lode mining sites in the Sheep Mountain mining district, Custer County, Idaho. Twenty-one mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were checked and the updated information added to the data base. The district's deposits are mainly confined to metasedimentary xenoliths in granodiorite and quartz monzonite. Those deposits in the north and west parts of the district are lead-silver-zinc replacement veins in dominantly calcareous facies; those in the southern part of the district are polymetallic fissure-veins containing pyrite, chalcopyrite, arsenopyrite, galena, and sphalerite hosted by micaceous schist and phyllite. The dominant structural trend in the southern part of the district is northwesterly and on strike with major deposits in the adjacent Seafoam mining district.

Jan 1, 1983

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By Mark S. Sanders

Six underground coal mine shuttle cars (three high seam and three low seam) were used to assess visibility using the concept of visual attention locations (VALs) and an improved human eye reference measurement instrument (HERMI Mark II). Each machine was assessed in the inby and outby direction of travel with no canopy and with the canopy in its highest, and lowest position. In addition, the illumination level at each VAL was determined. Results showed that the most important variable determining visibility was operator eye position. When this variable is controlled, the addition of a canopy has no effect on visibility. Further, with eye position controlled, there is no difference in visibility between high and low seam machines. The visibility and illumination assessments found blind spots in the operator's field of view located on the opposite side of the car from the operator and ahead of the machine. Suggestions for reducing the blind spots were made. The report also included a procedure manual for using HERMI and the system of VALs to assess visibility from underground shuttle cars, continuous miners, and scoops.

Jan 1, 1983

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By W. C. Babcock

This report covers Phase V of .a continuing program to apply a new liquid membrane process called coupled transport to the recovery pf metals from hydrometallurgical leach solutions. During this phase of the program, a membrane system of moderate scale was constructed and field-tested at the Exxon Highlands Mine and Mill Co. site near Douglas, Wyoming. The test unit contained four hollow-fiber membrane modules, each with 100 ft2 of membrane area. In the field tests, about 1000 gallons per day of leach solution was processed. The unit was operated on the leach solution for about 50 days. Leach solution entering the unit contained 100 ppm uranium. This concentration was reduced to about 5 ppm by coupled-transport treatment, and the uranium was concentrated to about 2 wt% as a uranyl carbonate product. Under these conditions, a transmembrane uranium flux of about 2.5 lb/ft2-year was obtained. An economic analysis showed that the cost of recovering uranium from this leach solution via coupled trans-port is about $1.20/lb. At higher concentrations of uranium in the leach solution this cost is reduced. For example, at 1000 ppm the cost of uranium recovery is about $0.30/lb.

Jan 1, 1983

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By J. G. Eacott

This paper reviews the role of oxygen potential and the advances that have been made in the application of tonnage oxygen in copper smelting. Brief reference is made to reaction kinetics before attention is turned to the thermodynamic considerations in copper melting to illustrate the importance of oxygen and. oxygen potential in the component parts of the overall smelting process. The chemical potential diagram for the Cu-Fe-S-O-Si02 system is used to elucidate the difference b etween the conventional matte smelting process and the modern continuous processes. A progressive oxidation scale' is constructed to show the common elements which exist, and the matte grades produced, during the smelting of concentrates to blister copper in commercially available copper smelting processes and those under development. The common route in producing blister copper from molten mattes, regardless of process, is illustrated on the Cu-Fe-S equilibrium phase diagram. The essential features of oxygen enrichment, in terms of its effect on combustion conditions (i.e. oxidation of fuel and sulphide minerals) and the heat balance are outlined. The benefits of oxygen enrichment are listed. The influence of tonnage oxygen and its effect on productivity, fuel savings, gas volume and strength in various copper melting processes are examined as a state-of-the-art review. Reference is made to the economics of tonnage oxygen utilization.

Jan 1, 1983

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983

By Charles A. Gargano

The current state of the mass transit industry in America will be examined. How and why this important urban activity shifted entirely, or almost entirely, from the private sector to the public sector. Who pays for transit? For day to day operating costs? For capital investment? The prospects for transit's future will be the next major issue addressed. In a word, they are rather good. Over the past decade there have been major new transit investments made in Atlanta, Baltimore, Washington, D.C. and Miami, as well as constant re-investment in such cities as New York, Boston, Philadelphia and Chicago. While the current administration has put a temporary halt on the initiation of any major new rail transit projects using Federal funds, there are several mechanisms localities have for using other resources for such projects. These will be explored.

Jan 1, 1983

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

Programmes of environmental investigations to identify and minimise impacts and satisfy government and community requirements have become an integral and rate determining component in the planning and development of new mines in Australia. This paper reviews the essential features of the environmental project management Function.

Jan 1, 1983

By W. J. Nosek

Reserve Mining Company completed construction on a major process modification project in June of 1980. These modifications enabled Reserve to reduce and control its final iron ore pellet silica content from 9.0 20.77 percent to 5.0 50.26 percent. The paper outlines the implementation of neutron activation on-line analysis and associated computer control loops for measuring and closely controlling the silica content of the iron ore concentrate at Reserve Mining Company. It contains a general overview of Reserve's taconite processing facilities and a presentation of the theory and operation of the neutron activation analysis equipment coupled with the computer silica control loops.

Jan 1, 1983

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983