Search Documents

By P J. Minehan

The investigation of the potential of the Webb/Baynes block of the Buller coalfield for anode carbon manufacture has generated much information on the physical beneficiation characteristics of the Buller coals in general. A further 36 drill holes of the block in question and several other samples have been analysed by sink/float analysis, either at a single density or over a range of densities. In addition, many samples have been beneficiated on a laboratory shaking table or by flotation. The ash content can be reduced by a variable factor. The reduction factor of between two and four by sink/float analysts is understandably less for tabling where separation is not perfect. All Buller coals behave similarly, there being greater ash reduction factors for higher ash coals.

Jan 1, 1983

By Robert H. Mattes

The Lake Lynn Laboratory is a multipurpose mining research laboratory operated by the Bureau of Mines and located in Fairchance, Pa, It consists of both surface and underground facilities. The initial focus of the facility, scheduled for full operation in fall 1982, will be on the problems of fires and explosions in mines. The initial experimental explosion was fired on March 3, 1982. The intent of this document is to provide the reader with detailed information on the physical capabilities of the Lake Lynn Laboratory. Subsequent publications will focus on the capabilities of Lake Lynn as compared with those of other similar facilities worldwide, and a comparison of initial explosion test results realized at Lake Lynn and comparable results from the Bruceton Experimental Mines.

Jan 1, 1983

The ore deposits of the Oobar mining field are confined to sediments of the Early Devonian Cobar Supergroup. The mineralisation is discordant to bedding and parallel to cleavage. The structural association is variable with the deposits near the eastern margin of the Cobar Basin formed in zones of deformation and faulting. The Elura deposit located further to the west is in less deformed sediments within the core of a small anticline. There are wide variations in ore type fran lad sulphide chalcopyrite - pyrrhotite - pyrite to high sulphide sphalerite - galena - pyrrhotite - pyrite assemblages. The deposits ccnmonly contain an inner zone of quartz - sulphide - chlorite veining grading outwards into a chlorite halo containing quartz - carbonate veining. The Elura deposit differs in having an inner massive sulphide zone surrounded by a zone of big-Fe carbonate formation. The mineralisation probably formed during regional metamorphism and deformation in the Early Carboniferous. A possible genetic model involves the injection of metal bearing hydrothermal fluids formed in the upper mantle or lower crust up basement structures into the overlying Cobar Supergroup sediments. An alternate model proposes the leaching of metals from the sediments by brines formed during metamorphism and subsequent emplacement in favourable structural zones.

Jan 1, 1983

By Nixon TR

The Australian Coal Industry Research Laboratories Ltd. (A.C.I.R.L.) MINVENT computer program can be used to simulate existing and projected colliery ventilation requirements. New collieries can be planned using a database of ventilation parameters which were ascertain- ed by A.C.I.R.L. surveys at selected collieries in N.S.W. and Queensland. Several techniques are used in both the formulation of the database and in the evaluat- ion of a ventilation system, prior to analysis by the MINVENT program. The analysis of a ventilation system requires the measurement of air quantities, pressures and hence airway resistances. All resistances are calculated at standard air density of 1.205 kg/m3. Air densities are derived from barometric pressure and wet and dry bulb temperature readings. Airway frictional and shock losses, leakage through stoppings and overcasts, flow of air through regulators, face resistance and resistance of anomalous ventilation features are related to the typical Australian measured data presented.

Jan 1, 1983

By James E. Lawver

At the present time, the Florida phosphate industry is experiencing one of the worst marked slumps in its one hundred year history. Recent agriculture over-production has caused low grain prices such that the net income of U.S. farmers is expected to drop to its lowest level since the 1932 depression. The farmers' low income, along with high interest rates that preclude them from borrowing to purchase fertilizer, make the immediate U.S. phosphate market outlook bleek at best. The export outlook is also pessimistic due to world recession and the U.S. dollar's high exchange rate. In June, 26% of the phosphate industry's workers were laid off for an indefinite period of time. Despite the immediate painful slump, the long-term outlook for the industry looks good. Florida has enormous reserves and will continue to produce a third of the world's phosphate supply simply by making changes in the present system of mining, beneficiation, waste disposal and land reclamation.

Jan 1, 1983

By F. E. Diebold

The methodology for describing the geochemistry of elements in a coal seam have been developed. This has been applied to the Rosebud Coal Seam, which is an economically important member of the subbituminous coals of the Fort Union Formation in Eastern Montana. The method development has involved a detailed study of two popular techniques for determining the metal geochemistry of coal, namely, whole coal analyses and coal physical fractionation. The mathematically contrived element associations (whole coal analyses technique) and the element concentration trends in the float and sink fractions (physical fractionation technique) are considered to lead to only qualitative conclusions concerning the chemical associations of the elements in coals. Additionally, the processes taking place with the coal during low temperature ashing in an oxygen plasma are experimentally investigated and shown to be of sufficeint extent that the use of such low temperature ash for deciphering element geochemistry is questionable. The method developed in this study is a chemical fractionation that involves the sequential leaching of coal with water, 0.5 N HC1, 3 N HC1, 2 N HNO3, and 48% HF. These leach solutions are shown to selectively dissolve the predominate inorganic phases, sulfates, Ca and Mg carbonates, Fe sulfides and K alumino-silicates and quartz, respectively. These phases were identified with the use of XRD, SEM, EM and leaches (water and 0.3 N HC1) of whole coal and low temperature ash. The incorporation of the anion-exchange step in the leaching scheme was investigated and was observed to warrant further study of such intensity to be, at the time, unuseable. The use of this sequential leaching technique on several coal samples from the same seam generates element concentration trends that can be quantitatively interpreted with respect to the chemical associations of the minor and trace metals in the coal seam. The properties of the various seams of economic importance in the Fort Union Formation in Eastern Montana are compiled and presented. The subsequent conclusion is that there is not a large variation in the properties of these coal seams and that the variations within the Rosebud are within one order of magnitude. The chemical fractionation technique, investigated in this study, was applied to composite tipple samples of the Rosebud seam. Each composite sample represented 76,800 tons of coal. A minimum of 32% of the Ca and Mg are present as separate water soluble sulfates. An excess of the sulfate ion in the water extracts shows the predominating influence of the ion exchange capacity of the organic compounds in the coal. Based upon the CO content of the coal and the HC1 leachate data, 25 to 30% of the alkaline earth elements exist as separate carbonates and the remainder are associated with the organic compounds. The small fraction of the illite that dissolves in the HC1 and HNO3 leachates accounts for the K and Al. Slight dissolution of the pyrite in the HCl solvent occurs, the small amounts of Li and As do not relate to any known phase and Mn is present as a separate carbonate phase. Fe and a significant amount of the As exist in the pyrite that is dissolved in the HNO. Se is equally partitioned between the pyrite and the organic compound~. Most of the trace elements are found in the HF solutions. Li, V, and Cr were interpreted to be associated with the clay minerals (kaolinite and illite). Ni and Pb appear to be present as separate phases and 50% of the Hg is HF soluble but is not chemically related to any known inorganic phase.

Jan 1, 1983

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By Madgwick J. C

A novel, microaerobic, heterotrophic microbial leaching system for manganese dioxide is described. Mixed natural microflora were enriched by addition of sugars and crude plant nutrItIOnal supplements. Between 84 and 104 mg MnH was solubilized per gram sugar at I per cent (w/v) concentrations for fructose and galactose in the presence of 0.03 per cent w/v dried microalgae (a Chlamydomonas species). Some 42 per cent soluble manganese was dissolved by microbial action on MnO, (3 per cent (w/v) pulp density) using a 10 per cent (w/v) molasses growth substrate.

Jan 1, 1983

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

By Mahoney BK

The development of simulation models to reflect accurately the operations of a port and its associated transportation systems can be an expensive and time consuming process. However the complexity of such operations leaves little choice for other than simulation techniques since analytical methods are rarely appropriate. The development of suitable software has now reached the stage that these techniques can be used with confidence. Types of simulation models and their requirements are discussed together with the results from some recent applications to the planning and management of bulk terminals.

Jan 1, 1983

By R. L. Wiegel

The generation of operating information for mineral beneficiation processes has become more sophisticated as a result of the use of improved laboratory analytical techniques, some of which provide multiple component assays, as well as the introduction and gradual industrial acceptance of process sensors for the measurement of flow, density, size, and chemical composition. In general, however, the mineral processing engineer's ability to tie together this wealth of information has not kept pace with these developments. In fact, in almost all existing plants, the metallurgical inflow-output balance, wed to indicate current process performance, is still being calculated from only a small portion of the information routinely available. There is substantial activity in the development of techniques for using all available process information to significantly improve the reliability of the metallurgical balance. While the use of these improved techniques does require access to computing facilities and a slight change in perspective on the part of the mineral processing engineer regarding the inviolability of process information, there are numerous practical benefits to be derived from their application. In addition to summarizing some of the concepts basic to these techniques, this paper describes the experience of the author in applying one of these advanced metallurgical balance techniques to a variety of pilot plant and commercial plant flowsheets during the past eight years.

Jan 1, 1983

By B. J. Scheiner

The Bureau of Mines, U. S. Department of the Interior, is conducting research on a dewatering technique for fine particles generated during the mineral beneficiation process that will recover a portion of the water now being lost using conventional waste disposal methods and significantly reduce the time required for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong stable flocs that can be dewatered rapidly on static and/or rotary screens. In field tests, phosphate clay waste has been dewatered from a nominal 2.5 percent solids to greater than 20 percent solids. In other field tests, coal-clay waste has been dewatered from a nominal 3 percent solids to greater than 55 percent solids, in addition, small-scale continuous tests have shown that bentonitic clays can be dewatered from 12 percent solids to 40 percent solids.

Jan 1, 1983

By Roy C. Bartholomae

This Bureau of Mines report presents the results of a laboratory investigation of coal cutting mechanics and noise. These experiments were performed using linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts was ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to formulate analytical models of the coal cutting forces and noise. The analytical model for coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as provide benefits to other important areas of health and safety in underground mining.

Jan 1, 1983

By D. C. Dahlin

The Bureau of Mines has investigated podiform chromite deposits in three ultramafic bodies in the Caribou Mountain and lower Kanuti River areas of central Alaska. The investigation, reported in two parts, was done as part of the Bureau's mission to help insure an adequate supply of minerals to meet the Nation's needs. Part I describes an extensive field investigation and mineralogical studies by personnel from the Bureau's Alaska Field Operations Center. This report, part II, describes the mineralogy of 11 samples that were high-graded from surface exposures at 10 sites and presents the results of laboratory batch beneficiation tests designed to concentrate the chromite. The 11 samples, peridotites and chromitites that consisted of variable amounts of chromite or chromium-bearing spinets, olivine, and serpentine, were beneficiated by grinding and sizing, gravity concentration, and electrodynamic separation. Three high-chromium chromite concentrates, two high-iron chromite concentrates, and one high-aluminum chromite concentrate were produced. Three other concentrates were marginal, and two were submarginal. Chromium recoveries ranged from 54 to 92 pct. These results indicate that the areas may be significant chromium resources. Potential platinum association with the chromite was also investigated. Analysis of these 11 samples indicates that the areas are not good platinum resources.

Jan 1, 1983

By Stephen Phillips, Luigi P. Gonano

Vertical circular shafts have been proposed for multiple access to high level nuclear waste deep geologic repositories. Shaft construction is a critical path item in the commissioning of a repository. Other constraints on the shaft design and construction criteria include the lack of design precedence for long term performance and the importance of minimizing rock and groundwater disturbance. A comparative evaluation of conventional and mechanized shaft sinking techniques is presented in the context of the particular geologic and design constraints. Technical and non-technical factors for blind drilling, blind boring, raise-reaming, drill-and-blast and ream-and slash methods are reviewed for typically "hard rock" and "salt" type repository sites. Appropriate shaft designs are developed, the suitability of each method to the particular requirements evaluated and construction costs and schedules determined. The explicit appraisal of the significant design factors for each method serves as a rational basis for the preliminary selection of the most suitable sinking technique for a particular set of site/design conditions.

Jan 1, 1983

By WL Wagner

This report presents a quality control approach to the derivation of strategies for monitoring a work environment; specifically, the environment in underground mines where diesel-powered equipment and blasting agents are used. The approach is presented as a series of 22 steps called the Monitoring Strategy Development Scheme. The scheme is an orderly method for selecting from a number of options a strategy or tactics to cost effectively meet the requirements of a chosen objective related to the monitoring of breathing zone air quality. The scheme provides a format to quantify many of the factors that influence the selection of on strategy or tactic over another, and to ensure that important considerations are not neglected. The premise that breathing zone air in work environment can be considered to be manufactured product and that, therefore, conventional quality control approaches are applicable, is introduced. Typical approaches to the quality control of manufactured products and how these approaches can be applied to the selection of monitoring strategies are discussed.

Jan 1, 1983

By Charles A. Kliche

INTRODUCTION The Northern Great Plains Coal Province which occupies approximately 36.6 ha contains about one-half of the nation's total coal resources. About one million ha are underlain by coal that is considered to be mineable from the surface. The topography of the province is predominately plains, rolling hills, and some badland areas characterized by breaks or sharply eroded hills. Elevations range from about 1500 m above sea level on the west to about 600 m above sea level on the eastern boundary. The average slope of the ground is approximately 2 m per km. Streams in the province drain generally easterly and southeasterly (1). In the United States, the Northern Great Plains Province lies within the states of North Dakota, South Dakota, Montana, Wyoming, Nebraska, and Colorado. The coal within the province is located almost entirely in the states of North Dakota, Montana, and Wyoming. Although it is relatively low rank, the coal within the province encompasses a large portion of the total remaining U. S. reserves. The U. S. Geological Survey estimates the total remaining coal resources of the United States to be 2.6 trillion mt within 1000 m of the surface, and 2.9 trillion tons within 1830 m of the surface. Of this total, only about 177 billion mt are classified as reserves meaning that they are (1) known in location, quantity and quality from geologic evidence supported by engineering measurements, and (2) economically recoverable based on currently available technologies and current market value (2).

Jan 1, 1983

An exploration and preliminary mine design contract was undertaken in Thailand to establish whether adequate lignite resources existed for the addition of future power generation plant through to the year 2000. The lignite ranges in heat value from 14 to 24 MJ/Kg (air dry basis) and occurs in 2 major seams consistituting measured reserves of 536 Mt (with an ash cut-off level of 45 % on an air dry basis) and a strip ratio of 4.1 bank cm/t. The paper describes the pre-planning, programming, equipment used, project management, logistics and exploration methods adopted to undertake the contract in a monsoonal area using Australian drilling and geophysical contractors.

Jan 1, 1983

Traditionally, the development of a mineral resource project goes through a fairly set pattern of decisions from what commodities to search for; where to look; how to locate; what are the reserves; how can they be exploited with optimum returns for all stakeholders; where are the markets and what will be the price received; what financing arrangments? However, due to the unique nature of most mineral resource properties, the relative significance of individual parameters on the ultimate development decision will vary from project to project. Sensitivity analysis in its formal sense is most frequently related to the economic analysis of a project particularly in conjunction with the ultimate development decision making process, and acknowledges the uncertainty of the actual values with their impact on the corporate decision making yardsticks. In many cases, this analysis merely adds more values to confuse the decision makers who may well opt for some subjective rationale to overcome the numeric confusion. However, sensitivity analysis should be used more frequently to exploit the development dollar to its maximum, THROUGHOUT the phases leading to the development decision. It is essential to identify the critical inputs to the various decision tiers in a project as early as possible and direct the funds to ensure that these parameters are determined as accurately as possible. Examples are used to illustrate the need for an even-handed quantification of the parameters which affect the outcome of decisions en route to the final one while minimising the risk in making an optimum assessment in relation to development funds Available.

Jan 1, 1983

By Jacqueline H. Jansky

The Mine Safety and Health Administration (MSHA), U.S. Department of Labor, did a linear analysis for a new underground coal mine in Grant County, WV, through the interpretation of LANDSAT imagery and high-altitude, color-infrared aerial photography, to identify areas of potentially unstable roof in advance of mining. The Bureau of Mines included this mine in its ongoing study of the correlation between geologic features and linears. Three years after the analysis, after mining had progressed through the plotted linears, a cooperative Bureau-MSHA study evaluated the effectiveness of the linear plot in predicting areas of unstable roof and defined the geology associated with the linears. Adverse roof conditions at this mine include roof falls, potted-out roof, water inflow, and local areas requiring supplemental support. At the time of this study, 34 pct of the mine workings were within 200 ft of a plotted linear. Fifty percent of the adverse roof area in the mine occurred within this area. The primary geologic anomaly associated with the linears is an increased frequency of jointing. The majority of the plotted linears coincide with the prominent joint orientations. Additional features observed in the linear zones include roof rolls and a sandstone channel that cuts into the coal seam.

Jan 1, 1983