Search Documents

By Johan K. Rodenburg

A major bauxite belt was discovered and evaluated from 1969 to 1974 by P. T. Alcoa Minerals of Indonesia in West Kalimantan, Indonesia. The proven reserves of beneficiated bauxite are 800 million tons averaging 38.6% AA1203 and 3.0% RSiO2. Inferred reserves of washed bauxite are in excess of 2 billion tons. The bauxite occurs as capping of low lying hills which were formed during the post Paleogene peneplaination stage. The overburden varies from 0.6 to 3.8 meters and the nodular bauxite horizon from 2.2 to 5.2 meters. The deposits were formed by the in situ weathering of predominantly acidic and basic intrusive rocks.

Jan 1, 1984

The captions to Figs. 1 and 2 of the paper by B. J. Parry entitled 'High-strength cold-rolled steels' should read as follows:

Jan 1, 1984

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

By Hassan El-Shall

Treatment of plant effluent including waste water and associated soluble and insoluble substances, is of a primary concern of many process industries including mineral processing operations. The major objective of such treatment is the removal of such impurities which can interfere with the process through the use of recycled water, and/or to comply with environmental ordinances. For example, Ramirez and Clements (1978) state that molybdenum contents in the range of 19 mg/1 eventually poison ion exchange resigns used for the extraction of uranium. In addition, recent restrictions by the EPA on molybdenum discharge values for mining waste water necessitate removal of this metal to (0.5-1.0 mg/1).

Jan 1, 1984

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By Armstrong AB

It has been identified that particulate matter in the form of suspended solids and bed load has the ability to adsorb heavy metals. Each year Ranger Uranium Mines Pty Ltd (RUM) identifies potential danger areas which could become major sediment sources during the wet season. Methods of suppressing sediment uptake such as hydromulching and coating areas with Poly Vinyl Acetate (PVA) glue are used. Other methods of reducing the sediment load after uptake such as diversion bunds, filters across drains, stone filters, minor sumps and settling ponds are also used. The 1983/84 wet season saw drain sediment loads reduced to acceptable levels before the water reached the outside environment. Studies to qualify and quantify flows from minor drains are still underway.

Jan 1, 1984

By A. W. Khair

Surface subsidence is a phenomenon mainly associated with longwall mining, although it can also occur if the coal pillar left to protect the surface deteriorates with time and results in the collapse of the room and pillar system. A method has been developed that utilizes physical mine models and laser holographic interferometry. This method is capable of measuring displacements as small as 5 micro- inches by means of generating displacement contours on a surface, even that of granular materials. Analysis of subsidence in room and pillar mining using models of various extraction ratios ad overburden depths along with two different types of overburden model material (sand and gelatin) has been made. The sand represented the extreme brittle conditions of geologic material while the gelatin represented visco-elastic behavior of geologic material. This paper deals with the analysis of data which has been gathered up to date, and mainly associated with the use of sand as an overburden model material. The analysis included the effect of variation of geometric parameters on surface subsidence. Among these parameters are: variation in seam depth and thickness, surface and seam inclination, and extraction ratio.

Jan 1, 1984

This publication summarizes the in-house and contract research projects programmed for fiscal year 1984 by the Bureau of Mines under its Conservation and Development activity. The document provides a mechanism for interested parties to gain insight into projects of the Bureau's Conservation and Development research program. The objective of the Conservation and Development Program is to provide the technological advances needed to stimulate the mining of domestic deposits containing critical, strategic, and other essential minerals in compliance with existing regulations and at costs sufficiently low to be competitive in world markets. Research efforts are directed toward improving the fundamental understanding of processes and procedures involved in the production of minerals. The overall goals will be accomplished by investigating alternative mining methods to increase domestic production of critical and strategic minerals from low-grade deposits; expanding the technology for the economic and efficient extraction of minerals consistent with cost-effective compliance with environmental regulations; and advancing the technologies needed to insure an adequate supply of coal.

Jan 1, 1984

In sizing of wet coal by the horizontal vibrating screen, screen openings to be used is much restricted, because coal is sticky and its bulk density is little. The electrically heated screen and other various types of screen had been tried to screen raw coal and coal as raw materials at a few mm. However, they failed to realize satisfactory results. On the other hand, fine sizing of coal is requested by many fields. For example, raw coal is desired to be screened at the fine rate, before being fed to the coal preparation control system in order to transport undersizes as unprepared coal particles and to reduce load in coal preparation waste water treatment system.1) Coals fed to the fluidized bed boiler also should be sized at a few mm. Regardless of many requests on fine sizing of coal, it seems that there are many cases to omit the basic screening process, because the screening is very difficult on a industrial scale. Size control as pretreatment of coal as raw materials is presented as one of the basic screening processes. In 1979, Kinki Industrial Co., Ltd. and Nippon Steel Corporation jointly succeeded in developing the vertical centrifugal screen. Closed -circuit crushing system by the use of this screen has operated actually at N.S.C, Hirbhata .Works, and realized the anticipated result. Consequently, this system has established the position as the most basic technology in the coal preparation. 2), 3), 4) This system has been also introduced to Nakayama Steel Works, Ltd. in 1982. This system termed the CPC (Coal Preparation Control) Process has been operated smoothly in both N.S.C. and Nakayama. Reported herein is the practical application of the vertical centrifugal screen termed V3-Separator. (V3 means vertical, versatile and vibration.)

Jan 1, 1984

By Dyson NF

Nickel sulphide precipitated from waste liquors at the Yabulu plant of Queensland Nickel Pty Ltd was pressure leached under various conditions. Leaching at 130¦C and 700 kPa of air dissolved 95 per cent of the nickel as the sulphate in less than 2 h. Leaching at 130¦C and 350 kPa of oxygen dis- solved 95 per cent of the nickel in less than 1 h. Dissolution was faster with oxygen than with the equivalent pressure of air. Crystallization of hydrated nickel sul- phate from the resulting clarified leachate is readily achieved. Because the sulphide pre- cipitate also contains minor amounts of iron, copper and cobalt, the crystallization product contains these metals in excess of the amounts required for electrolytic-grade nickel sul- phate. This grade of product could only be produced if the contaminants were removed prior to crystallization. Alternatively, the "crude" nickel sulphate could find a market as a feed for the electrolytic production of Ni-Fe coatings.

Jan 1, 1984

By T. G. Rozgonyi

The basic goal of this investigation was to determine the degree of drying of high moisture lignite through the use of high temperature and pressure steam autoclaves. Specific items studied were: a) the effect of lignite particle size, b) steam temperature and pressure required, and c) the time of ahydration. Although removal of sodium, ash, sulfur and other ash-forming minerals was not the goal of this study, basic analysis of effluent water showed organic material and alkalai metal content. Removal of inherent moisture from run-of-mine lignite was tested by lock-feeding the lignite, which was previously sized by screening into 25 kg autoclaves. High pressure, up to 4.053 MPa (588 psi), saturated steam was then introduced into the pressure reactor. Reaction time, pressure, temperature, and depressurization rates were strictly controlled for each reactor test run. Results indicate that about 80% of lignite total moisture was removed, including some of the inherent moisture, yielding a non-oxidized, and thus stable, lignite product. As stated, a side benefit occurred as some reduction of non-combustible portions of the lignite also took place. The conclusion reached as a result of the tests is that the steam-drying process can be successfully applied to reducing moisture in lignite, and may be considered for additional studies on acceleration of the coalification process. On the basis of the data presented, the author believes that lignite can be economically upgraded in steam autoclaves by simultaneously reducing the moisture content by 80 percent and the sulfur content by at least 50 percent. Upgrading the lignite by this method will result in large energy and financial savings.

Jan 1, 1984

By R. E. Green

The Bureau of Mines undertook a bench-scale study of three different types of oxidized taconites3 from the Lake Superior district to improve the dispersion-selective flocculation-desliming process for beneficiating these materials. The response-surface contours of the effects of dissolved ionic species in the water and of three dispersion systems on the selective flocculation process were studied. Results of metallurgical data and chemical analyses of the aqueous phase showed that the water quality affects the performance of the selective flocculation process.

Jan 1, 1984

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

"The Archaean komatiite-associated nickel sulphide deposits at Kambalda, Western Australia, exhibit a number of stratigraphic features that are indicative of a strong volcanic control on ore localization, including (1) a restriction to specific basal cumulate metakomatiite host units, (2) confinement within distinctive synvolcanic embayments in the footwall and (3) variations in the internal structure and composition of overlying and adjacent barren metakomatiite flow's and the distribution of interflow metasediments with proximity to the ore zones.The high magnesium content of the host units (up to 45% MgO volatile-free) in comparison with that of aphyric or spinifex- textured lavas (16-32% MgO) has been considered previously to indicate either magmas/lavas rich in intratelluric olivine or selective accumulation of olivine phenocrysts. The marked linear trend of the oreshoots, basal host units, footwall embayments and the volcanic stratigraphic relationships have been used as evidence for local linear feeding fissures. Rare relict igneous olivine in some host units is, however, demonstrably not intratelluric, and there is no direct or indirect evidence of a proximal eruptive site (e.g. footwall feeders, pyroclastic breccias, ultramafic intrusives) at Kambalda such as at some other deposits of this type. Kambalda is interpreted as a distal rather than proximal volcanic environment.Emplacement of the komatiite sequence at Kambalda was probably controlled by the locations of a few specific eruptive sites relative to regional topographic gradients and influenced by the topography of the pre-existing volcanic surface. Olivine enrichment in the basal host units occurred by in-situ fractionation and cumulus crystallization of olivine during longitudinal lava flow within linear lava conduits, possibly centralized on depressions between non-overlapping footwall basalt flows. The distinctive stratigraphic relationships are attributed to localization of lava conduits along the volcanic pitchline, flanked by more slowly moving parts of the flows. There are analogies with the physical volcanology of Modern basaltic and Proterozoic komatiitic lava flows.A corollary of this model is that the lava conduits thermally eroded and assimilated sulphidic sediments, contributing additional sulphur to sulphur-saturated komatiites or possibly inducing sulphide separation in originally sulphur-undersaturated komatiites. The latter would account for the restriction of ores to linear cumulate komatiite host units (thermally active lava conduits) and the locally mutually exclusive, but stratigraphically equivalent, relationship between the ores and sulphidic metasediments at Kambalda."

Jan 1, 1984

By Lung Cheng

The Bureau of Mines has installed passive water explosion barriers in two operating mines to determine their usefulness in U.S. coal mines. The primary objective of this field trial was to determine the effect of the explosion barriers on mining operations. Data were also obtained on the ability of the barriers to withstand the mine environment and on the effect of the barriers on belt operation, ventilation, worker travel, and rock dusting. Fifty barriers were installed at three separate beltway locations, and periodic inspections were made. A year after installation, no defects of the barriers or support hardware were detected, nor was any complaint as to the presence of the barriers made by the mine personnel. To date, 2-1/2 years after installation, the barriers have had no detrimental ef-fect on rock dusting, belt operation, or ventilation. Costs of material, fabrication, and installation are reported herein.

Jan 1, 1984

By V. Lakshmanan, Dan Mackie, J. Melnbardis

"Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market, with plans to begin production of a 500 TPD operation in 1984.Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogeneous grinding. In addition to producing marketable coarse graphite by such autogeneous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies. INTROOUCTIONWhen the Black Oonald mine at Calabogie Ontario ceased production in 1954 nearly all North American crystalline flake graphite had to be imported from offshore. Orebodies in the United States were too small or too low in grade to be exploited economically.The Houthillier Township near Mont Laurier in Quebec (Figure 1) was a known graphite-bearing area The Orrwell property in that area was delineated in 1957 Some test work including minor footage of diamond drilling was carried out by Italia Copper and the MHM Syndicate prior to 1981 when Orrwell acquired the property"

Jan 1, 1984

By J. W. Sterner

The Bureau of Mines conducted studies on four makes of Japanese automobiles, three 1981 and one 1982 model years, received from three manufacturers to determine if their materials composition would present problems to the current technology used to process junk automobiles for metal recovery. One of each make of automobile was hand-dismantled to determine the materials composition. In addition, two nearly identical automobiles of each make were shredded at a commercial operation where all metal products and rejects were collected for analysis to determine metal and nonmetal distribution. The average weight of the four automobiles to be dismantled, less batteries, tools, and fluids, was 1,938.3 lb. The weight was distributed as 1,472.9 lb. ferrous and 115.6 lb nonferrous metals, 275.2 lb combustibles, 72.3 lb noncombustibles, and 2.3 lb electrical components. The dismantled automobiles, less gas tanks, fluids, tools, wheels, tires, and batteries, which were all removed from the automobiles that were shredded, contained an average of 1,389.1 lb ferrous and 101.6 lb nonferrous metals, 305.7 lb nonmetals, and 2.3 lb electrical components. In comparison, materials collected from the shredded automobiles averaged 1,304 lb ferrous metals, 80 lb nonferrous metals, and 341 lb landfill materials. There were no materials used in the manufacture of the late model Japanese automobiles that should present handling or processing problems to the steelmaking or secondary metal recyclers.

Jan 1, 1984

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984