Search Documents

By J. R. Batista

Leachates from gold heap-leaching mines contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina when using relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for full-scale activated alumina processes. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH > 5.0. Silica adversely affected the selenium adsorption capacity. At pH values < 4, silica was poorly adsorbed by alumina and selenium adsorption was improved.

Jan 1, 1994

By T. N. Singh

An evaluation was made on the cavability of the roof formation of Dishergarh seam including caving sequence, caving span, and load on powered support.

Jan 1, 1994

The Resource Management Act 1991 (RMA) and the Crown Minerals Act 1991 (CMA) both came into force on 1 October 1991. The purpose behind RMA was to integrate the existing laws dealing with town and country planning, land subdivision, water and soil, minerals and energy resources, coastal management, air pollution and noise control into one omnibus Act. Originally, there was a section in RMA dealing with minerals. However, this section was taken out of RMA and a companion piece of legislation - namely CMA - was passed with RMA.

Jan 1, 1994

By F. Ajersch, P: Tsantrizos, K: Shanker

"TiN films have been deposited on various substrates by a novel reactive plasma technology. In this process, a nitrogen source (NH3 or N2) and TiCl4 are reacted in the jet of a plasma torch, and are deposited onto a substrate forming TiN films at a high growth rate ( > 2µm/min). It was found that the process parameters strongly affect the microstructure, thickness, density, and growth rate of the TiN films. These parameters include source of nitrogen (NH3 or N2, N/Ti ratio, temperature of substrate, and spray distance. In general, it was found that thick and dense coatings were deposited when the N:Ti ratio was kept low, and the substrate temperature was high. Also, for the series of conditions investigated, NH3 was found to give much better results than N2•. The limitations and advantages of this technique are also discussed in this paper.IntroductionTiN is an extremely hard material and is used in many wear applications, particularly as a protective coating on cutting tools to extend their Iife(1.2). Owing to its excellent chemical stability, TiN is also frequently used as a diffusion barrier in the electronics industry for sub-micron Al/TiN/Si ohmic contact systems (3) or as a coating on high-temperature resistant alloys in gas turbine applications (4), based on its good resistance to oxidation. Other applications include decorative coatings in the jewelry industry, and specialized applications such as solar energy absorbers and transparent heat mirrors(5).TiN films can be deposited/formed using various techniques. The main techniques of deposition are CVD (Chemical Vapour Deposition) and PVD (Physical Vapour Deposition). Each of these techniques can have many variations in equipment characteristics, reactants as well as a range of process parameters (pressure and temperature). In the CVD process, TiN is generally deposited onto a heated substrate where a chemical reaction takes place. The reaction can be one of reduction(6) (e.g.: TiCI4 + 0.5N2 + 2H2 --> TiN + 4HCI), of thermal decomposition(7) (e.g. decomposition of titanium dialkylamide), or of displacement (e.g. TiCI4 + NH3 --> TiN + 3HCI + 0.5CI2)' The displacement and reduction reactions are the most common."

Jan 1, 1994

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites that contain mineral assemblages derived from the crystallization of post- magmatic fluids or from the metasomatic action of residual peg- matitic fluids. They have been the traditional sources of raw material for ceramic and chemical industries. With the discovery of the Searles Lake deposits, brines became new sources of lithium, and, today, two brine deposits satisfy nearly one-half of the free world demand for lithium chemicals. Indeed, lithium production from pegmatites has been superseded by brines sources. In the United States, the brines of Clayton Valley, NV, have been exploited since 1964 by Cyprus Foote Mineral Company, a subsidiary of Cyprus Minerals Company. In Chile, Sociedad Chilena de Litio Ltda., an affiliate of Cyprus Minerals Company, is now producing lithium carbonate from the brines of the Salar de Atacama. Recently identified brine deposits suggest that these may well become the prime sources of lithium chemicals. In Bolivia, the government is negotiating the rights to exploit the brines of the Salar de Uyuni. The Salar del Hombre Muerto in Argentina is being evaluated as a future center of chemical production. The brines of the Great Salt Lake of Utah, the Smackover Formation, and the Imperial Valley geothermal field have been defined as important resources of lithium. In Tibet, high concentrations of lithium have been reported in several saline lakes. In the People&apos;s Republic of China, lithium may be produced from the brines of the Dabusan playa in the Qinghai Basin. The 1950s saw a great number of lithium companies develop. However, following the termination of the Atomic Energy Commission purchase program in 1959, several companies, such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp., were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminumpotlines), the lithium industry grew steadily. With the potential application of lithium metal in batteries, nuclear reactors, and fuel cells, a steady growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Presently identified reserves and production capacity are sufficient to satisfy the conventional market growth of lithium.

Jan 1, 1994

By Connie Postupack

The purpose of the workshop is to show the effect of various blasting factors on the overall results.

Jan 1, 1994

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant&apos;s -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene. &nbsp; Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

By J. G. Groppo

Lowering of filter cake moisture of ultra-fine coal to a 20 percent level using conventional vacuum filtration could be achieved using a combination of metal ion and surfactants. Pretreating coal slurry with about 0.2 Kg/ton of a surfactant and 50 ppm of copper or 10 ppm of aluminum ions provided filter cake containing 22.8 percent moisture. The lowering of moisture is explained due to formation of hydrophobic micro-agglomerates which facilitates dewatering.

Jan 1, 1994

What is `environmental risk&apos;? There are two possible perspectives: (a) The risk that mining activity will have an impact on the environment. (b) The risk that due to a perceived impact on the environment, the mining activity is at risk due to some legal consequence. This paper is concerned with the second of these perspectives, and particularly with the way in which mining companies can manage that risk. Environmental risk - possible legal consequences The risk is that the mining operation will be disrupted. Disruption may be: (a) Physical. The mining activity can be stopped, altered, or modified, or something additional can be required to be done. (b) Financial. Penalties (up to $1M) on corporations and in some states on both directors and managers. Land may also be included on a contaminated land register (significant impact on asset valuation).

Jan 1, 1994

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting&apos;s Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By S. K. Kawatra

It is common in coal-cleaning operations to produce a fine waste stream which contains a considerable amount of coal, but which is not economical to recover both because it is mixed with large amounts of difficult-to-remove clay slimes, and because the fines are often heavily oxidized. Conventional froth flotation machines cannot produce an acceptable product from such material in a single stage of flotation, and even flotation columns often have difficulty cleaning this type of feed. A new type of flotation column was designed specifically to deal with these problems, and was installed and tested in a coal-cleaning plant in Ohio. The feed coal contained 39.8% ash as fine clay, and 2.83% total sulfur, and was 80% passing 176 micrometers. The coal was a thickener product which had oxidized for some time, and was very difficult to float. However, using the new column it was possible to recover up to 85% of the calorific value in a product containing less than 11% ash, and up to 60% of the calorific value in a product of less that 8% ash. The bulk of the pyritic sulfur was rejected from the coal as well. Multistage flotation tests showed that the flotation column was able, in a single stage, to produce the best froth flotation product that it was possible to recover from this coal.

Jan 1, 1994

Structural geological information is widely used at the Mt Whaleback Mine, Newman, WA. Recent improvements in the structural understanding of Mt Whaleback are providing a very cost-effective way of reducing geological risk, improving the economics of mining, optimising pit design and addressing safety problems. The structure of the Mt Whaleback orebody is highly complex and has a significant influence not only on iron ore genesis but also on pit wall stability. A team approach between the Structural Geology and Geomechanics Groups has been providing excellent results to reduce geological risk at Mt Whaleback.

Jan 1, 1994

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By E G. Prado

We have confirmed on bench scale the removal of chlorides and alkalies (+95%) and over 2/3 of the zinc, lead and cadmium from EAF dusts. This has been achieved with arrononium acetate solutions alone, or with combinations of water wash, amonia-ammonium carbonate and ammonium acetate solutions. Also confirmed are the process routes for the recovery of the aforementioned elements into marketable products. The technology involves the complete recycling of the reagents. The FAF residue is returned to the electric furnace without risk of impurities buildup. Commercial scale testing with the recycled dust was satisfactory, including quality of the slag and its behavior during the melting stage. A cursory feasibility evaluation is presented.

Jan 1, 1994

By King D, Dickinson S. B, Matheson R. S

Commencing in 1956, Rio TInto Australian Exploration Pty Limited in association with Electrolytic Zinc Co of Australasia, Limited, has been carrying out a mineral prospecting program in North-West Tasmania over an area of about 4000 square miles.The program has comprised extensive airborne geophysical surveys, detailed geological mapping, ground geophysical and geochemical investigations. Out of the wealth of new data, and the examination of previous records, has emerged a new structural concept of regional ore control and distribution in North-West Tasmania. This roncept stems from the discovery of an ancient &apos;fossil&apos; rift valley (graben), named the Owen Rift Valley, along which are located the major mines of the area and numerous well-known prospects. The known mines and prospects from north to south include Mt Bischoff (tin); the Pinnacles (zinc, lead, ropper); the Chester (pyrites); Rosebery-Hercules (lead, zinc, ropper, silver, gold); Mt Tyndall (lead, ropper, zinc); Comstock and Tasman (copper, lead, zinc); Mt Lyell (copper, pyrites, gold); Mt Jukes and Mt Darwin (ropper). The identification of the West Coast (Owen Conglomerate) Range as a fossil rift valley is due to Or B Campana, who carried out extensive geological mapping and interpretation work, and who, with S B Dickinson, are the senior authors of this paper.S B Dickinson, who introduced B Campana to the geological problems of West Tasmania, had previously investigated the Mt Lyell and Rosebery mining fIeld, to which reference is made in this work.D King assisted in the regional mapping and in providing numerous data on the mineral distribution of the area.R S Matheson rontributed to the fmdings on ore emplacement and rontrol in the discussions held on this subject. They are accordingly included as joint authors of this paper.Credit is also due to E McCarthy, who interpreted the geophysical results, and to J H Rattigan, who compiled the preliminary geological maps from published documents and by photo-geological methods.G Hall and V H Cottle, of the Electrolytic Zinc Co in Rosebery, provided invaluable geological data and suggestions in the course of the survey, and made a constructive criticism of the manuscript of this work. The airborne geophysical survey carried out by the Adastra-Hunting Geophysics Ltd company, furnished useful data which substantiated many of the fIndings on the stratigraphic and structural relationship. The Mines Department of Tasmania and S W Carey, Professor of Geology at the University of Tasmania, were instrumental in initiating the regional survey and provided the published and unpublished geological literature on the area.The authors also wish to acknowledge the invaluable assistance received from the Mt Lyell Mining and Railway Co in Queenstown, which made available the more recent geological and mining documents rompiled by M L Wade and M Solomon.

Jan 1, 1994