Search Documents

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By Caelli T, Robey M

Most research into planning of open pit mines has been based on evaluation of volume-element block models in terms of their net present value. The major issues revolve around two interdependent problems the optimum ultimate pit and time-based scheduling. Despite feedback between the two problems, they are usually treated as separate tasks.The ultimate open pit is defined by the removal of whole blocks so that their net present value is maximised. This gives planners an estimate of the total worth of the venture in present terms, and is crucial to obtaining funding. All cost and profit values are assumed to be static throughout the mine life, and the only physical constraint usually taken into account is that of safe, average, wall slopes, which must be approximated by the removal of whole blocks. Modelling of any further constraints (for example, access roads and true wall slopes) is usually achieved by adding them to the optimal pit by hand. Typically this degrades the model by between five and 20 per cent of its value - which then brings into question whether it is still the true optimum.This paper reviews the dominant methods in use for this first task the ultimate open-pit planning problem. Some new optimisations are given, and the algorithms are examined in terms of their efficiency and accuracy. Finally, suggestions are made for improvement of model accuracy and eventual expansion into solutions of the more complete dual problem - that of simultaneously finding the optimum ultimate pits and dynamic schedules for the venture.

Jan 1, 1996

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By Rosie Moore, Harvey Keats, Kerry Sparkes, A. J. Naldrett

"Abstract-The Voisey’s Bay Ni-Cu-Co deposit was discovered in late 1994 as the result of prospecting initiated in the summer of 1993. By July 1995, proven mineable reserves were 31.7 x 106 tonnes grading 2.83% Ni, 1.68% Cu and 0.12% Co, and current total resources in all categories are quoted to be in the order of 150 X 106 tonnes. The deposit is associated with a body of troctolite belonging to the Nain Anorthosite (1.35 Ga - 1.29 Ga) suite, which was emplaced across the boundary between the Proterozoic "Rae" Province to the west and Archean "Nain" Province to the east.The deposit can be described in terms of three geological settings. The "Ovoid" is a 600 m long by 350 m wide by 100 m deep lens of massive sulfide, covered by 10 m to 20 m of glacial overburden, and separated from the underlying country rock quartz-plagioclase-biotite gneiss by a breccia of gneissic fragments in troctolite known as the Basal Breccia Sequence. To the west of the Ovoid lies the "Western Extension", comprising disseminated and massive sulfides in a north-dipping sheet of troctolite which ranges from upper unmineralized troctolite down through troctolite with increasing amounts of sulfide (up to 50%), to massive sulfide (in some places only), and then to Basal Breccia Sequence. East of the Ovoid, the troctolite sheet broadens out into a troctolite intrusion, within which occurs the "Eastern Deeps", a zone of massive and disseminated sulfide up to 100 m thick that is currently being explored. The mineralization of the Eastern Deeps lies along the line of intersection of a feeder sheet with the base of the intrusion. The current interpretation is that the three geological environments represent different erosional levels through a single mineralized intrusion. In this model, the deepest erosional level lies to the west and exposes the feeder to surface, whereas the Ovoid represents the base of the intrusion at surface, and the Eastern Deeps the base of the intrusion overlain by 600 m to 900 m of troctolite. Sulfides and gneissic fragments were brought up by magma flowing quickly through the feeder, and settled out where the flow rate decreased as the sulfide-bearing magma mixed with magma already emplaced in the intrusive body."

Jan 1, 1996

By N. T. Rempe

Proper use of natural resources is multiple use. Underground space resulting from mineral extraction offers opportunities for deep geologic waste disposal (DGWD) which can solve many environmental problems. U.S. government projects plan to use specially mined excavations to dispose of radiotoxic and mixed waste. DGWD takes careful planning, technology transfer, and true partnership between waste generators and mine/repository operators. Using the experience, accumulated by domestic projects in preparation, and by foreign repositories in operation, U.S. mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1996

By J. C. Norman

The United States was the world’s largest producer and consumer of boron compounds during 1995. According to estimates from the US Geological Survey(USGS), boron mineral concentrate and chemical production in the United States totaled an estimated 1.1 Mt(1.2 million st) yielding 602 kt (663,000 st) of B2O3 for an estimated value of $462 million. This level of production exceeded 1994 revised production figures by about 9%. The United States continued to provide nearly all its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid to foreign markets. During 1995, about 900 people worked in domestic boron mines and plants, about the same as in1994. USGS estimated total world production of boron during 1995 to be about 3 Mt (3.3 million st), yielding about 1.6 Mt (1.8 million st) of B2O3. World production in 1995 was about equal to revised 1994 levels.

Jan 1, 1996

By G. H. Robbins

"Originally presented at TORONTO 94, CIM-AGM, this paper has been updated to reflect the present status of business development for theSO2/AIR process. The paper reviews the back-ground leading to the invention, discusses the process chemistry and historically tracks the commercial development. Engineering and cost considerations are presented.IntroductionThe year 1994 was particularly significant in terms of the technical and business development of the INCO SO2/AIR cyanide destruction process. The year marked a decade of service to the world mining community since INCO acquired the Canadian patent in 1984. In that time period, the technology had become widely recognized as the state-of-the-art process in the field of cyanide detoxification and today we enjoy the distinction of having licensed the process at over 50 project sites worldwide. The application for the process has mostly been in the mining industry in precious metal recovery plants where it offers treatment for a wide range of waste streams such as: CIP/CIL slurries, Merrill-Crowe barren bleed solutions and/or re-pulped filter cakes, tailings pond water recycle or discharge, make-up water to flotation circuits and feed to underground backfill plants. The process also applies to the treatment of high cyanide rinsewaters from metal plating shops. More recently the process is being applied to the rinsing and abandonment of heap leach pads where it has proven to be a very cost-effective application of the INCO process. The distinct advantages that have led to the success of the process are the ability to work on slurries as well as solutions and the significantly low cost of sulphur dioxide products. The process is safe and easy to manage and uses all forms of SO2(liquid, gas or salts) which gives the process tremendous versatility with respect to geographic application. Having more than ten years of service"

Jan 1, 1996

By P. Somasundaran, S. Venkatachalam, N. K. Khosla, K. Khosla

Froth flotation of alumina particles was studied by employing and hydrogen gas bubbles. The effect of current density was studied over a range of 0.1 to1.6 kA/m2. Compared to hydrogen, the use of oxygen bubbles at any given gas evolution rate resulted in a higher flotation recovery. The existence of an optimum current density, for each given particle size was indicated. Flotation at higher current densities resulted in better flotation kinetics, while flotation at lower current densities resulted in better Spas utilization.

Jan 1, 1996

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996

By Catharine E. G. Farrow, David H. Watkinson

Abstract-The Ni-rich Epidote Zone of the Fraser Mine at Sudbury is characterized by alteration assemblages rich in epidote, actinolite and magnetite which are roughly concentrically zoned and up to hundreds of meters in length. These zones form discrete areas within the igneous Footwall Breccia below the Sudbury Igneous Complex. The assemblages grade from epidotized Footwall Breccia matrix, through actinolite-bearing rocks with few vestiges of original Footwall Breccia textures, into the most intensely altered rock, a magnetite-rich facies. Pentlandite, pyrrhotite and pyrite are the dominant sulfide minerals; chalcopyrite is minor. The strongest geochemical differences compared to original Footwall Breccia occur where epidote and actinolite dominate the alteration assemblage (EPDZact facies). The most intense alteration facies are typified by low Cu/(Cu+Ni) values of <0.1. Strong positive correlations exist between Ni and Co, Cu and Au, and among Ir, Os, Ru and Rh. Chondrite-normalized Ni - PGE - Au - Cu plots display an overall increase in all elements from the least to the most intensely altered facies except for Au and Cu. As the proportion of actinolite increases in the EPDZact facies, the chondrite-normalized profiles flatten considerably due to low Au and Cu contents. Abundances of Ni, Ir, Ru and Rh almost ubiquitously increase with degree of alteration. In contrast, Cu, Zn, Ag and Au contents are low in almost all facies. It is suggested that saline hydrothermal fluids moved through the Epidote Zone formation and became more oxidized as they reacted with the Footwall Breccia and with footwall units, including ultramafic rocks. As this trend continued, magnetite-rich zones eventually developed. The occurrence of calcite locally in these magnetite-rich zones suggests that the pH of the fluid increased, causing Cu solubility to drop as activity in the hydrothermal system waned. Sudden changes in fluid composition such as this may have been due to an influx of fluid from bounding ultramafic rocks. Hydrothermal activity was focused along the margins of footwall ultramafic units. Individual hydrothermal cells may have formed in the Footwall Breccia along pre-existing structures or sulfide concentrations. Metals may have been scavenged from sulfide-bearing Footwall Breccia and possibly Sublayer rocks. Nickel and some PGE were deposited in the Epidote Zone, whereas Cu, Au and Ag continued outward into the footwall where they were deposited as Cu-rich footwall veins.

Jan 1, 1996

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

South Africa?s now a member of this body, tailored on the World Bank, and headquartered in Abidjan-Cote d&apos;Ivoire. As a funding agency for capital projects within 59 member countries of the ADB it is to be expected that there are guidelines to the requirements for funding application and for project management and control.

Jan 1, 1996

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By R. Cavanagh

Studies relating to the fixation of sulfur by reaction of 4 to 8 mm diameter cylinders of calcined limestone or dolomite with high strength sulfur dioxide in the temperature range 880°C to 1020°C were undertaken. Dolomites are far superior in sulfate capacity and reactivity than dense limestones even at high strength SO2. The sulfation reaction was first order with respect to SO2 concentration below 100 percent. Zero reaction rate at 100 percent SO2 concentration indicates that sulfate was the exclusive reaction product and that sulfite had no role in the reaction. At relatively low SO2 concentrations gaseous diffusion through the reaction product layer has a marked effect on the rate. As SO2 concentrations were increased up to 100 percent more complex rate controlling mechanisms unfold. By sectioning partially reacted dolomitic limestone pellets a moving interface was observed. Reaction ceased because of pore plugging for dense non-porous limestones at 30% conversion. With dolomitic material virtually complete sulfation of the calcium was observed. S.E.M. analysis showed that the average atom ratio Ca:S was 1.01, thus supporting the argument that little if any of the magnesium was sulfated.

Jan 1, 1996

By Donald R. Sadoway

"Molten salt electrolysis is a proven technology for the extraction of metals -- all· the world's primary aluminum is produced in this manner. The unique properties of molten salts also make them excellent media in which to treat a variety of forms of waste. Of special note in this regard is electrolysis in molten oxides, a concept put forward by the author, initially as a ""clean technology"" for producing primary metal. However, in the context of waste treatment, electrolysis in molten oxides is a process offering the prospect of changing the-valence of dissolved heavy metals while making pure oxygen gas as the main by-product. Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3, SiO2; CaO, and MgO have confirmed electrochemical production of oxygen on a carbon-free anode. IntroductionMolten salt electrolysis is the electrolytic decomposition of a compound dissolved in an ionic melt. The prime example of this process can be found in the production of aluminum. The compound, alumina (Al2O3)' derived from the mineral bauxite, is dissolved in an ionic melt comprising a multicomponent solution of cryolite (Na3AlF6)' aluminum fluoride (AlF3)' and calcium fluoride (CaF2,). The products of electrolysis are molten aluminum and carbon dioxide, the latter due to the attendant consumption of the carbon anode. Primary aluminum is produced in a reactor known as the Hall cell.' Alternatively, the compound undergoing electrolytic decomposition can be derived from waste. Processing in molten salts, with their capacity to dissolve materials to very high concentrations compared to those attainable in aqueous solutions, can be rather advantageous. High solubilities lead to high limiting current densities, and this, in tum, results in high productivities: For a primer on molten salt electrolysis and a review of the basic literature in the field of molten salts the reader is directed to an earlier publication of the author (1)."

Jan 1, 1996