Search Documents

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By Corby G. Anderson

In the majority of industrial operations recovering gold and silver by hydrometallurgical means, cyanide is the predominant lixiviant. However, as an economic alternative, production of massive quantifies of silver chloride was done on an industrial scale in the nitrous-sulfuric acid pressure leaching of a refractory precious metals concentrate. This proven process required no cyanide. Thus, because of the large volumes encountered during day-to-day plant operation, the need for efficient and low cost methods of silver chloride precipitation, reduction and materials handling was mandatory. As such, this paper covers the evolution of plant scale precipitation, filtration, washing, reduction and control of silver chloride processing. As well, an in-depth description of the unique leaching system is included.

Jan 1, 1998

By Hideki Shimando

Periodic weighting and windblast which are caused by the dynamic effects of overburden in a longwall panel significantly affect longwall mining This study describes past experience with wind blast at Miike Colliery, proposes a new loosening system using hydraulic fracturing and moistening, and also discusses strength deterioration in hard-to-collapse roof rocks due to water in order to solve the problems caused by the effects of dynamic roof rocks behavior in a longwall face

Jan 1, 1998

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

This paper focuses on two sites in the Mount Pleasant - McCormacks Bay area of Christchurch where residential development has taken place either within or immediately adjacent to former quarries for the extraction of volcanic rock. At the Quarry Road site less overburden was dumped on adjoining land around the turn of the century, and c.1980 dwelling and related construction took place on approximately 6 m of relatively loose fill material without the recognition of its presence or geotechnical characteristics. Subsequent settlements led to abandonment of a swimming pool and the underpinning of the 3-storey architect-designed house, whilst litigation brought by the owner resulted in findings of negligence against both the architects and engineers. At the Tramways Quarry site the Council approved subdivision of the former quarry area in the early 1980s without requiring any geotechnical evaluation of batter stability or related issues. During development it became apparent that significant blast damage had occurred to rock faces, necessitating a variety of remedial measures, and that waste materials had been dumped down faces without regard to long-term stability. Both case studies confirm the requirement for careful documentation of former quarry sites by territorial local authorities as part of their administrative function, and for detailed engineering geology and geotechnical evaluation of such areas prior to any residential use of the land.

Jan 1, 1998

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By I Cameron

Simulation is increasingly being used to analyse mineral processing operations and explore efficiency options. Engineers that use simulation are rightly concerned with the quality and applicability of the underlying models. However, many of these models have a significant empirical component, and the best structure for this component may not be apparent. There is an opportunity to improve the quality and application range of these models by exploring potential structures for this empirical element. One approach to this problem is the use of structural optimisation, which is a formalisation of the model development process. This method searches through a family or hyper-structure of candidate models for a model that is optimal with respect to some measure of model quality. This method has been applied to the modelling of an industrial flotation circuit. The result was a model that was a significant improvement over a number of standard models reported in the literature. Structural optimisation provides a method to compare potential models in a systematic and efficient way, and hence to improve the structure of process models.

Jan 1, 1998

By Roger G. Sprague

With the passing of time, changing marketplaces and years of hard service, coupled with new machines, increased productivity, rapidly improving technology, equipment which used to be the latest in modern mining have now slipped into obsolence. Mining companies need reliable, productive equipment in order to compete in today's market. In Western coal mining, as coal seams become deeper, older equipment must be replaced with that which can do the job more efficiently.

Jan 1, 1998

By A. Coulombe

"RésuméL’analyse des séquences d’exploitation, actuellement en usage pour les gisements très inclinés, a démontré qu’elles ne sont pas toujours optimales du point de vue du contrôle des terrains et de la concentration des travaux d’abattage (nombre de chantiers simultanément en opération). Effectivement plusieurs séquences sont très propices à la création des nombreuses zones de hautes contraintes, qui sont à l’origine des effets de pilier. L’étude de cas de la mine Lac Shortt a démontré que certaines séquences d’exploitation, actuellement en usage, ne sont surtout pas adéquates dans le cas d’un état élevé des contraintes naturelles. En effet la mine a eu de sérieuses problèmes avec le contrôle des terrains (coups de terrains et les effondrements des épontes). Ces effondrements étaient responsables de la dilution excessive et des pertes importantes des réserves minières. Les deux nouvelles séquences proposées, visent la meilleure redistribution des contraintes d’exploitation en vue d’éliminer la création des effets de pilier. En plus elles permettent une concentration plus élevée des travaux d’abattage.À notre avis les séquences proposées pourraient améliorer substantiellement la stabilité des chantiers d’abattage et par la suite les performances technique et économique des opérations souterraines. ABSTRACTThe planning of underground mining sequences represents an important aspect of the mining operation. The analysis of mining sequences actually in use for very steep orebodies has demonstrated that they are not always optimal, considering ground control and the number of stopes simultaneously in extraction. These sequences are conducive to the creation in the rockmass of several stressed zones caused by pillar effects. The case study of Lac Shortt mine showed that the sequences of exploitation currently in use are not adequate especially in the case of a high state of the natural constraints. Indeed, the mine had serious problems with ground control (rock bursts and collapse of walls). These collapses were responsible for excessive dilution and significant losses of mining reserves. The two new sequences suggested aim for the best redistribution of exploitation constraints in order to eliminate creation of pillar effects. Moreover, they allow a higher number of stopes to be extracted simultaneously. In the opinion of the authors, the sequences suggested could substantially improve the stability of working areas and, thereafter, technical and economical performances of the underground operations."

Jan 1, 1998

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By Kiyoshi Shibata

A new assessment model has been proposed for metal production and its recycling system. The model consists of three processes, smelting of ore, cascading and upgrading of metal scrap. The present approach is to assess the total energy consumption of the system, by introducing two equations for describing the relationships between critical impurity content and the mass of production or scrap recycling. The total energy consumption in the system can be described as a function of recycling rate and performance of the upgrading process. The present model suggests that the impurity removal efficiency and yield in the upgrading process are essential to reduce the energy consumption in the systems. Especially, such points should be explicitly controlled in recycling of aluminum. The potential capability of this model was also discussed by obtaining several quantitative information required for the process design and the operational control of beneficial recycling of metals.

Jan 1, 1998

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By B. J. Madden

Over 206 million tons of hard coal were mined in South African collieries in 1996. Some 132.5 millions tons came from underground operations and approximately 120 million tons came from bord-and-pillar workings resulting in between 100 000 and 150 000pillars being formed. Coal pillar design remains a significant feature of South African mining. This paper reviews South African coal pillar design procedures in the light of 90 pillar collapses that have occurred since 1904. It shows that, while the current pillar strength formula is still valid within the original empirical range of Salamon1,cognisance must be taken of local conditions. Current South African coal pillar research is attempting to account for the variations in local conditions with the emphasis on the effect of discontinuities and pillar deterioration. It is suggested that a more holistic approach to pillar design be adopted to include a design methodology that examines the stability of the roof, pillar and floor of the underground workings. Using this approach, deviations from the empirical database used by Salamon and Munro will be incorporated into the design methodology resulting in more stable underground workings.

Jan 1, 1998

By Patrick Ph. D. Kennedy, Osvaldo A. Ph. D. Bascur

With the revolutionary progress in information and computer technologies, applying the latest information technologies in metallurgical complexes has become a serious challenge to both a major opportunity and a serious challenge to both management and technical teams. The emerging component and object technologies are changing the way everyone can beneficially use their computer and networks to add to their corporate bottom lines. Most mining and metallurgical plants use predictive maintenance policies based on statistical analysis and special techniques, like vibration analysis and oil and lube analysis for critical equipment. Process control strategies are installed in several metallurgical sites. All process equipment and control strategies require maintenance from local personnel at the mine. Integrated use of existing and emerging technologies is making it possible to implement an overall process effectiveness control index. This index is based on key indices such as losses due to plant availability, performance efficiency and rate of quality. The availability of real time and process history to identify the most critical part of the processing system from mechanical integrity is highlighted. An emerging plant integration paradigm is described to simplify the implementation of business enterprise resources management and distributed plant management systems.

Jan 1, 1998