Search Documents

By H G. Bosmare, G Bedser, C V. B Cunningham

Peak Quany has achieved substantial improvements to its bottom lie by giving close attention to blasting practice, and in pr@icnlar by introducing electronic delay detonators for routine production blasting. The precision and flexibility provided by these units has enabled the quarry to gain control over fmes and curtail oversize without increasing explosive usage. In addition, the extent of nuisance from blasting vibrations has been reduced.

Jan 1, 1998

By D Crequer

A Peer Review Panel for the Golden Cross Mine in the upperWaitekauri Valley, Coromandel was initiated in December 1989, before mining, as a requirement of the conditions of the Mining Licence and Water Rights. The panel's function is as a technical audit and advisory team - to provide independent technical review of design, construction, and execution of mining operations, slope remediation works, and reclamation/mine closure activities. The primary role of the panel is to act in the public interest by providing assurance to regulating authorities that the design and application of on-site mining operations accords with 'good industry practice'. Panellists are not involved in design nor as advisers, although until 1997 when explicit terms of reference were written, the panellists were a sounding board for some operational proposals. The panel functions to ensure that best mining industry technical standards are met. The costs of the peer review process are met by the mining company. Review of mining operations includes environmental matters such as land rehabilitation and water quality. The focus of this paper is on the process of peer review for environmental management factors rather than for structural and mine engineering.

Jan 1, 1998

Coal washery wastes comprise tailings, finer than 0.5 to 0.1 mm depending on the sophistication of the washery, and coarse reject, typically finer than 50 mm. Subaerial disposal of coal tailings slurry at about 30 per cent solids by mass results in the formation of a delta with an average slope of about 1 in 100, representing one extreme. The ravelling of coarse reject on loose-dumping, results in an angle of repose slope with an angle of about 37o (1 in 1.3), representing the other extreme. The pumped co-disposal of coal tailings and coarse reject results in the formation of an upper delta with an average slope of about to one in ten, between the two extremes. The depositional behaviour of these three waste streams is discussed and compared in this paper. The important depositional and material parameters, and a theoretical description of the processes involved, are also presented. Comparisons are made between the depositional behaviour of the various coal washery waste streams, and natural depositional systems, such as rivers, alluvial fans, and scree slopes.

Jan 1, 1998

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous ones because of their fatality records. Statistical testing of 1993 West Virginia safety and production data indicated that the most efficient WV mines were not the safest ones, considering correlations between the severity measure and tons per employee-hour, except for very small mines. This paper will present the results of an extended analysis of WV mine safety using 1993 and 1996 data, concluding with the method used to suggest current priorities for focusing interventions.

Jan 1, 1998

By K B. Quast

During the prefeasibility stage of the mining cycle for a gold deposit, an evaluation of the ore leaching characteristics from various defined areas is essential prior to plant design. There are a number of simple laboratory tests which have proven successful in establishing gold and silver leaching kinetics, carbon adsorption and fouling, as well as elution characteristics. A number of case studies of carbon-in-pulp (CIP) simulation are presented which show excellent agreement between calculated and assayed gold and silver grades in feed and adsorbed on carbon which validate the methods used.

Jan 1, 1998

By Richard H. T. Garnett

Marine mining on the continental shelf was first attempted in 1900 for gold off the beaches of Nome, Alaska. Attempts continued until 1990 with cutter-suction, airlift and bucket-ladder dredges. Offshore Thailand profitable production of tin resulted from clamshell, bucket-ladder and trailing suction hopper dredges. Today in Indonesia numerous bucket-ladder dredges continue to mine tin. Off the coast of Namibia and South Africa nearly a dozen large and medium sized vessels are engaged in diamond production. The obvious risk results from the working environment. Vessels and lives have been lost in the past. At best the availability of mining equipment is reduced. Leaving aside the marketing and financing aspects, otherwise the most important risks are technical. They manifest themselves as diamond production short-falls with obvious financial consequences. Bias and deficiencies in sampling equipment and procedures may result in misleading grade estimates, even serious under-estimation. Inadequate sampling in terms of sample support and density may result in over-optimistic grade determinations, especially if under-sized mining blocks are outlined. Quantitative measurement of the geotechnical characteristics of the sediments to be mined is an essential stage in a feasibility study. Without a full understanding of the bedrock profile and the overlying sediments the ease, completeness and speed of excavation during the mining process cannot be properly estimated. Both historically and at present the greatest negative discrepancies from production estimates result, not from grade shortfalls, but from significantly lower mining rates than thought possible by the operators. The learning curve in marine, production mining is steeper and longer than is generally recognised by newcomers to the industry. Examples are provided from tin, gold and diamond mining experiences.

Jan 1, 1998

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By Alexander Malahoff

The summit of L_ihi submarine volcano changed dramatically after seismic activity beneath L_ihi during the month of August 1996. Bathymetric re-surveys of the L_ihi edifice using SeaBeam, Simrad and deep-towed Reson-Focus multibeam systems showed the presence of new north-south striking fissures, normal faults and a new pit crater located at the site of a former 300-meter high volcanic cone. Comparisons between the pre-1996 SeaBeam data and the new bathymetry show a net loss of about 100 million cubic meters of rock volume on the summit. This loss is localized at a new pit crater -- the 300-meter deep by 1,300-meter wide Pele's Pit. Submersible observations with Pisces V show the northern edge of Pele's Pit to be bounded by a normal fault located north of the site of the former Pele's Vents cone that has disappeared into the new pit crater. A new hydrothermal field, the Ikaika Vents, extending from a water depth of 1,311 meters to 1,287 meters has formed at the northeastern edge of the floor of Pele's Pit. Submersible observations of these new Ikaika Vents during September 1996 showed vigorous venting at the site with extensive white-colored bacterial mats hanging off the rock face above the vents. Follow-up mapping and sampling of the vent sites during August 1997 showed vent temperatures of up to 198°C, dense populations of vent shrimps around the vents and a centimeters-thick veneer of fine-grained polymetallic sulfide mineralization along the rock walls above individual vents. The mineralogy of the sulfides shows a barite, chalcopyrite, sphalerite, and pyrite composition.

Jan 1, 1998

By D Morrison

Backfill is usually considered a necessary evil that contributes little to the principal objective of the operation, ore production. Consequently, it is relegated to an auxiliary role in the operation with minimal equipment and resource allocation in planning and is only superficially considered during feasibility studies. In many mines, the inadequacy of the design and operation of the backfill system ultimately leads to frequent delays, excessive costs and, in the worst cases, major instabilities which result in reduced ore production and lost or unrecoverable ore reserves. The primary objective of backfill is to prevent the progressive deterioration of mined out excavations. With the exception of narrow vein operations, it is too weak to alter the mining induced stress regime and control stress concentrations caused by stope extractions. However, the direct benefits of backfill include the possibility to consider a wider range of mining methods, recovery of 100 per cent of the planned resource and the selection of a stoping sequence that minimises the regional stability problems that cause production shortfalls in the later years of mine production. Indirectly, backfill is a practical means of solving other issues, such as waste disposal, that impact the viability of mining. In Australia, the geotechnical conditions of many mines are becoming more difficult and increased attention to the importance of backfill is warranted. This paper describes realistic aspects of backfilling and the positive impacts a well co-ordinated fill system can have on mining activities as a whole. Examples are presented where an integrated approach to backfill systems have offered significant benefits to the operation.

Jan 1, 1998

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By D. D. Runnells, G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology, including such factors as thermal and chemical stratification, turnover and the development of anoxic conditions with depth. Limnologic data collected from four existing pit lakes in Montana and Saskatchewan indicate that pit lakes develop a thermocline (temperature stratification) in the upper 10 to 30 m (33 to 100 ft) of the water column. Two of the pit lakes, 26- and 55-m (85and 180 ft) deep, undergo seasonal turnover of the entire water column, whereas two deeper pit lakes, 110- and 240-m (360- to 790 ft) deep, undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column, and a distinct chemocline develops with depth.

Jan 1, 1998

By Robertson AC

Studies by Tennent, Isokangas Pty Ltd (TIP) have indicated that underground quarrying of backfill may be a cost competitive option for providing backfill for specialised situations in underground mining. Situations where suitable bulk fill material may not be available on the surface, and where the total cost of setting up a fill distribution system are prohibitive, could favour the mining of fill material underground adjacent to the stopes being mined. Considerations include environmental impact, scheduling, surface constraints and total costs. The examples quoted in this paper, and the case studies are based on the authors' personal observations and experience.

Jan 1, 1998

By R. E. Robinson

A novel variation of the GYPCIX process for the treatment of the acid mine effluent water from Grootvlei is described, in which a number of valuable by products can be obtained and the product water can be used for a variety of different purposes. A conceptual case study is presented in which the important cost parameters are described and certain critical path activities are indicated in order to derive a Return on Investment evaluation according to methods previously published. The study indicates that the treatment costs can be dramatically reduced, provided that proper utilization of the by products is taken into account. There are many possible uses for the water. However, by far the most advantageous contribution to the RDP and the best return on capital is derived if the water is used to establish small-lot farming activities providing work opportunities for thousands of people and contributing several hundred million Rands to the GDP. Vastly improved social conditions will be generated in an area of Gauteng that is in danger of rapid deterioration and a contribution will be made to maintaining mining activities in this area. The environmental impact is positive.

Jan 1, 1998

By S. Illendula, B. Q. Li, R. A. Mirshams

"An integrated mathematical model is developed to represent the thermomechanical behavior of the materials and microstructure evolution during metal forging. The model development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The procedures for the integration of the microstructure model into the macro finite element model are described. Computed results for both macro and micro phenomena during metal forging, such thermomechanical deformation such as velocity field and effective strain rate and materials characteristics such as distribution of grain size and recrystallization volume fraction, are presented.1. IntroductionThermomechanical behavior and material microstructural evolution are two critical, interrelated aspects associated with metal workpiece undergoing large plastic deformations such as encountered in forging processes. In much of the modeling work up to date, these two aspects have been addressed separately. Die designs and forging processes are investigated using finite element based thermomechanical models while material dynamics during forging is studied, more often than not, as a separate subject. For many industrial applications, especially those involving novel, light and high strength materials, it is critical to combine these two aspects into a single, integrated model so that materials dynamics and thermomechanical deformation during forging processes can be considered simultaneously [1], thereby providing required information for intelligent process design and optimal process control."

Jan 1, 1998

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

The history of the rail and mining industry in Queensland over the past century is inseparable. Indeed it was mining that led to the construction of the line west from Townsville and that shaped its current alignment. The discovery of gold at Charters Towers started construction of the Great Northern Railway west from Townsville in 1879, with completion to Charters Towers in 1882. The line was extended to Hughenden in 1887 and to Cloncurry in 1907 - driven by copper mines both to the south west and the north west of Cloncurry. The mining industryÆs association with funding the construction of rail lines to service their individual mines began in this area when the Hampden and Mount Elliot mine companies agreed to pay 50 per cent of the cost of the line from Cloncurry. The line to Selwyn was completed in 1910. Copper mining saw the construction of many other rail lines in the Cloncurry area in the 1910 - 20 period before copper prices slumped. Included in these lines were the Malbon to Duchess line and the line to Kajabbi and beyond.

Jan 1, 1998

By Jussi Vaamol

A commercial CFD-code was used to solve isothermal flow fields of gas and liquid in a Peirce-Smith converter. The model was validated with a 1/4 scale water model, and parametric study. Limits of the modeling technique used were recognized, but calculated results indicate that the present model predicts the general flow field with reasonable accuracy. The model was used to examine general flow conditions in an industrial scale PS-converter. Typical scaling factors of physical models were also evaluated with the aid of predicted bubble distribution, patterns of the flow fields and magnitude of flow velocities. The numerical simulations were found to open new viewpoints to the fluid dynamic related phenomena in the PS-process.

Jan 1, 1998

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998