Search Documents

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

This chapter presents proportionate mortality ratios (PMRs) derived from death certificate data in the National Occupational Mortality Surveillance (NOMS) database for the years 1986 through 1993. At the time this report was prepared, 1993 was the latest year for which data were available. Industry is classified under the 1980 U.S. Bureau of the Census classification system [Bureau of the Census 1982]; cause of death, under the International Classification of Diseases, Ninth Revision (ICD-9) [World Health Organization 1977]. A PMR of 100 indicates a mortality risk for a particular industry group that is similar to that for all industry groups combined. A PMR over 100 suggests a higher risk; a PMR under 100 suggests a lower risk. PMRs are subject to many factors that affect their reliability and validity and may not be comparable across populations with very different causes of death. An elevated PMR for a specified cause of death among an occupational or industry group may indicate a relationship between a work exposure and the cause of death specified. However, there are many limitations of PMRs as a measure of risk; they are most useful for generating hypotheses about exposure-disease relationships, which can then be tested in other studies. Selected PMRs are presented separately for males and females for coal mining, metal mining, nonmetallic mineral mining and quarrying (which includes nonmetal, stone, and sand and gravel), and for oil and gas extraction. All PMRs have been adjusted for age and race. In general, PMRs are presented only if the lower 95% confidence limit exceeded 100. If a PMR in an ICD-9 subcategory was above 100, however, the PMR for the larger category into which the subcategory falls is always presented and may be less than 100. PMRs can be expected to be elevated for conditions that have a high prevalence in particular occupational groups. PMRs showed elevated values for conditions known to affect miners, such as coal workers' pneumoconiosis, pneumoconiosis due to silica, tuberculosis, chronic pulmonary heart disease, and injuries. Additional findings of interest were- • An elevated PMR for myocardial infarction among male coal miners (table 2-1); • Elevated PMRs for neurologic disease in general and anterior horn cell disease, in particular among male metal miners (table 2-3); • An elevated PMR for rheumatic heart disease in male metal miners (table 2-3); • Elevated PMRs for malignant neoplasms of the digestive organs and peritoneum and for malignant neoplasms of the colon and rectum in female nonmetal miners (table 2-6); and • Elevated PMRs for non-A, non-B hepatitis and arteriosclerotic heart disease among male oil and gas workers (table 2-7).

Jan 5, 2000

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers' ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By Fumio Hashiuchi, Yushiro Hirai, Masatoshi Maeda, Toshihiro Nagata

"Increase in the copper smelting capacity at Saganoseki Smelter & Refinery was attained through various improvements in the PSconverters and the flash furnace. Two of the major innovations in the converting process were: a new operational technology which avoids increase in the copper content in the converter slag even when higher copper grade matte (65%) are treated in the slag making stage and a technology which shortens the operational interruption time which is caused by coolant charging. The latter was realized by introducing a new automated coolant charging system with which it was made possible to charge the coolant without stopping the blowing into the converter. These improvements brought about a remarkable increase in · the production capacity per converter and an annual production of 450,000 tons of copper without adding new furnaces was made possible. In addition, good results have been obtained of the tests with modified tuyeres to further increase the production.IntroductionIn a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major restructuring efforts since 1994. One of its themes was the shift from· a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 tons per annum of copper). Then, the productivity was enhanced to 450,000 mtpy without adding new furnaces through technological and operational improvements. It is now planned to increase the smelting capacity further to 470,000 mtpy this year.Some technological and operational improvements in the matte converting process and the new plan resulted from the tests with modified tuyeres are presented in this paper."

Jan 1, 2000

By S. Paul Singh

Rock is a heterogeneous medium, a fact often ignored during blast design. In reality, the rock mass characteristics have a controlling influence on the outcome of a blast. If the optimum blasting results are to be achieved over a range of rock mass conditions, it is prudent to understand the role played by the geological features of a rock mass in producing overbreak around the periphery of an excavation. The field work was performed in a drift located in a geologically dominant rock mass and also included observations and assessment of blast damage at several operating mines. The blast damage was estimated on the basis of the half cast factor. The effect of rock strength, rock quality designation, orientation , frequency and aperture of joints, number and thickness of layers and hydrogeological conditions on blast damage has been described.

Jan 1, 2000

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By Thierry Bernard, Jean Marc Laboz

This paper explains why and how integration of EIS (Electronic Initiation System) with dedicated software tools can increase benefits to blasters and at the same time simplify the design of blast sequence

Jan 1, 2000

By Fuxing Yin, Akira Sato, Yoshiaki Ohsawa, Kohji Kawaharai

"INCRAMUTE alloy (nominally 45Mn-53Cu-2Al wt. %) has a specific damping capacity as high as 0.4, through a solid-solution and aging treatment. The damping behavior of the alloy is highly temperature-dependent and shows a peak near room temperature. The inadequate strength in the high damping condition restrains the practical application of the alloy, as structural components. Ferromagnetic MnB particles are dispersed in the alloy during induction remelting the matrix alloy in an argon atmosphere. Surface modification of the MnB particles by mechanical alloying (MA) and suitable control of the addition process cause a homogeneous distribution of MnB particles in the alloy. In the composite containing 2 wt. % MnB particles, temperature dependence of damping capacity is improved, and higher damping capacity is still retained in the temperatures over 60 °C. Meanwhile, the Young's modulus and tensile strength were also increased by about 20%. The roles of the MnB particles in improving both damping behavior and mechanical properties were also discussed.IntroductionMany viscoelastic materials, such as rubbers, polymers and plastics, have the superior ability to damp vibration and noise. However, in the applications as structural materials the high damping capacities of materials are pursued upon the satisfactory mechanical properties, especially those at elevated temperatures. Damping alloys are finding more and more applications in structures where noise and vibration ·should be ·eliminated. Specific damping capacity (SDC), defined as the ratio of the energy dissipated to the maximum vibration energy stored per cycle, is usually used to evaluate the damping capacity of alloys. INCRAMUTE damping alloy, developed by the International Copper Research Association, Inc., has a nominal composition of 45Mn-53Cu-2Al in weight percent. The high damping· microstructure of this alloy is obtained through the solution treatment at 820 °C followed by a water quench and aging at 400°C for 10 hours followed by cooling to room temperature [1]. With the heat treatment, a SDC peak ·vs. temperature of as high as 0.4 was observed in the alloy at the strain amplitude of about 10-3 while a tensile strength of about 500MPa was sustained."

Jan 1, 2000

By Eddie C. Chou

Phelps Dodge, Inc. (PD) is currently developing a lateritic nicke/Vcobalt deposit in Madagascar. Hazen Research, Inc. provides technical assistance to PD to investigate recovery processes for nickel and cobalt. Various process options were evaluated in laboratory experiments and pilot plant operations. The process selected for the feasibility study consists of feed preparation, high-pressure acid leach, countercurrent decantation wash, sulfide precipitation, sulfide dissolution, solvent extraction, ion exchange, and electrowinning. Among these unit processes, high-pressure acid leach, sulfide precipitation, and sulfide dissolution are applications of pressure technologies. Process development work and design criteria for commercial operations of these unit processes are presented in this paper. Concerns related to scaling in the high-pressure acid leach and the sulfide precipitation processes are discussed. Corrosion of various metal coupons under these environments was examined.

Jan 1, 2000

By Kuniaki Murase, Tetsuji Hirato, Koji Nitta, Yasuhiro Awakura

"The redox behavior of copper species in an ""ammonium imide"" room temperature molten salt was examined in order to clarify the applicability of the salt to the electroplating media of various metals. Trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)- amide (TMHA-Tf2N), having an electrochemical window of 5.6 V (50 °C), and corresponding copper(II) salt were synthesized. In TMHA-Tf2N media monovalent copper ion, Cu(I), was stable and Cu metal was oxidized, or corroded, in the presence of Cu(II) species. Cathodic electrodeposition of copper metal and anodic dissolution of it were, thus, one-electron reaction and their current efficiencies were almost 100%.IntroductionElectrodeposition of metals from aqueous solutions is an important soft process for manufacturing thin-film materials, surface finishing, and extractive metallurgy. However, the electrodeposition of base metals, such as zinc, chromium, and nickel, from aqueous media inevitably accompanies hydrogen evolution, which lowers the cathodic current efficiency of metal deposition. Since the electrodeposition of aluminium, titanium, and rare earths from aqueous media is actually impossible due to their largely negative redox potentials, nonaqueous media such as aprotic organic solvent and high-temperature molten salts have been employed for the electrodeposition of these metals. Room temperature molten salts (RTMS),1, 2) or room temperature ionic liquids, have also been developed as a promising electrolytes for the electrodeposition of base metals. In this field, chloroaluminates of alkylpyridinium or alkylimidazolium cation have been well investigated for aluminium3) or alluminium-alloy4-5) electroplating media. On the other hand, in order to avoid high hygroscopicity arising from the use of aluminium chloride, attempts have been made to combine the alkylimidazolium cations with fluorine-containing hydrophobic anions, e.g. BF4-,6) CF3SO3- (TfO-),7) (CF3SO2)2N- (Tf2N-),8) and H(HF)n-ions,9) and investigated for electrodeposition media.'°) Recently, a new series of RTMS consisting of tetraalkylammonium cations and Tf2N- anion, sometimes abbreviated as TFSI- anion, was found independently by MacFarlane et al.11, 12) and Matsumoto et al. 13) This type of RTMS, which is commonly named ""ammoniumimide"" salt, has a wide electrochemical window of ca. 5 V and, thus, the RTMS seems to be suited for practical application as a solvent for the electrodeposition process. In this paper, we report the electrochemical behavior of copper species in an ammoniumimide RTMS, trimethyl-n-hexylammonium bis(trifluoromethanesulfonyl)amide (TMHA-Tf2N)."

Jan 1, 2000

By J. W. Neale

Mintek and BacTech have joined forces to provide the metallurgical industry with bacterial-oxidation processes for the treatment of sulphide ores. The processes are aimed at both refractory gold-bearing and base-metal concentrates. Previously, BacTech had commercially implemented the refractory gold process at the Youanmi Gold Mine in Western Australia. More recently, the process has been incorporated in the Sulphide Treatment Plant at the Beaconsfield Gold Mine in Tasmania, Australia. In addition, Mintek and BacTech have recently signed an agreement with the Laizhou Gold Metallurgy Plant in China?s Shandong Province, which will see the third commercial realization of the technology for refractory gold. Development of the base-metal technology is the subject of several papers in the proceedings of this colloquium. The implementation of the refractory gold technology at Beaconsfield is discussed in detail. Some important aspects that are covered include: ?Test work, and the choice of bacterial culture ?Process design choices, and the advantages of the Mintek-BacTech process ?Inoculum build-up ?Plant commissioning ?Plant performance. Besides the Laizhou project, Mintek and BacTech are currently investigating several other commercial prospects for the technology. These include the use of the technology for a gold-copper deposit, where the production of both gold and copper is envisaged.

Jan 1, 2000

Mineralisation was identified at Gladstone Hill as far back as the late 1870s-early 1880s, shortly after the initial discovery of mineralisation at what is now the Martha Mine. Indeed, early recovery problems associated with the Martha mineralisation led to the preferred development of ore bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, and Union to name a few. Gladstone Hill forms the basis of the Union Hill Joint Venture, a 50:50 joint venture managed by Au-Ag Resources Ltd (a fully owned subsidiary of Otter Gold Mines Ltd), and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Mine. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Mine, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with a number of vein sets throughout the tenement including the Gladstone Vein set, the Moonlight Lode and more recently along a north-easterly trend towards the historic Favona workings. A wide range of vein styles is apparent, ranging in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz and have been interpreted as representing multiple phases of emplacement. At shallower levels mineralisation is often hosted by vein clasts within vent breccias. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. Percentage levels of combined sphalerite-galena-(+/- chalcopyrite) have been intersected at depth however these have been gold poor to date. The potential for the Gladstone Hill area remains to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 2000

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By A. Dogan Paktunc

Abstract - The Mechanic Settlement pluton is a small body of mafic and ultramafic rocks of tholeiitic affinity, occurring in the Late Neoproterozoic volcanosedimentary rocks of the Avalon terrane of the Appalachian Orogen. The lenticular-shaped intrusion is layered and consists of ultramafic and mafic lithologies in at least six cyclic units that are relatively thin or short-lived. The lowermost exposed portion of the intrusion is characterized by the cumulate sequences of olivine and olivineclinopyroxene and display relatively flat rare earth element profiles. In the overlying lithologies, plagioclase is the dominant cumulus phase following olivine in the crystallization sequence. Olivine ranges in composition from Fo73 to Fo85 and plagioclase from An62 to An89. Variations in the compositions of orthopyroxene and clinopyroxene are within Wo0-4En52-87Fs11-45 and Wo39-50En23-50Fs3-19. These mineral compositional variations in part reflect cryptic patterns and correspond to normal fractionation trends in cyclic units. Elevated Pt and Pd concentrations of up to 2.6 ppm occur in ten zones within the central cyclic series in association with both the peridotitic and gabbronoritic rock types. The mineralized zones are about several meters thick and appear to have lateral continuities over several hundred meters, suggesting that they are stratiform. Platinum-group elements (PGE) occur as discrete platinum-group minerals (PGM) including vysotskite, merenskyite, michenerite, sperrylite, stillwaterite, and hollingworthite that are associated with magmatic sulfides composed of pentlandite, pyrrhotite, and chalcopyrite. PGM grains range in size from a few micrometers to well above 20 µm. Sulfur isotope ratios and the Se/S ratios of the mineralized rocks are typically higher than the mantle values. Sulfide saturation probably occurred as a result of assimilation of crustal rocks and magma mixing during emplacement of subsequent pulses of magma. Repetition of the PGE mineralization in rather thin cyclic units suggests that the replenishing magma probably had high PGE levels and was saturated with respect to sulfide during emplacement. Ingression of the replenishing magma into the chamber in a turbulent plume and its mixing with the resident magma was probably responsible for the formation of the PGE mineralizations in the Mechanic Settlement pluton.

Jan 1, 2000

By Barend Botha, Trevor Davids

The presence of an extensive soft siltstone layer in the middle of the inter-burden sequence of rocks at Syferfontein Colliery in the Republic of South Africa prompted tests to determine the effect of different mid-column decks of inert material in the siltstone layer. The objective was to achieve significant cost savings in explosives use whilst not degrading dragline productivity. An important factor that had to be considered was that the initiation systems available in South Africa are not accurate enough to ensure simultaneous initiation of explosives decks in a blasthole. A number of inert materials were tested including ash, drill cuttings, river sand and crushed stone. It was found that the ash, drill cuttings and river sand did not effectively attenuate the shock wave and that the risks of sympathetic detonation or partial disruption of one or the other explosives deck in a blasthole was high. This became much worse when the inert material was saturated with water. Crushed rock was the most effective in attenuating the shock wave, but this material was very expensive to use because it had to be imported onto the mine.

Jan 1, 2000

By F. Shahbazian

attempt to systematize the knowledge on slag viscosities, the present work was carried out. The Among the physical properties of slags, viscosity is very important in understanding the mass out in the temperature range 1438-1762 Q The rotating cylinder method was used in the viscosity measurements. Crucibles and spindles made out of pure iron were employed. The transfer phenomena in metallurgical processes. The viscosities of fayalitic slags are of great interest in the non-ferrous metal industry, with special reference to copper production. In an slags were prefused before the measurements. In order to take into account the vaporization reactions involving CaF2, pre- and post measurement samples of the slags were chemically analysed and the compositions were ascertained. The results show that in the case of the CaO-SiO2 system, CaF2 additions tend to decrease the viscosity, in accordance with the expectations. In the case of the "FeO"-SiO2 system, at higher "FeO" / SiO2 ratios in the slags, a reverse trend was observed. The results are discussed on the basis of a viscosity model for silicate melts developed in the present laboratory as well as the structural considerations of silicates.

Jan 1, 2000