Search Documents

In order to reach a large, untapped reserve of high-quality coal, D8 Cloverlick mine proposed to mine a corridor nearly 2,000 ft deep beneath the Benham Spur of Black Mountain, Kentucky’s highest peak. D8 Cloverlick mine was extracting the Owl seam, but the corridor’s route lay approximately 70 ft above century-old mine workings in the C–(Darby) seam. Adding to the concern, three serious coal bursts had recently occurred in nearby Owl seam workings.

Jan 7, 2020

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

Longwall mining has existed in Utah for more than half a century. Much of this mining occurred at depths of cover that significantly exceed those encountered by most other U.S. longwall operations. Deep cover causes high ground stress, which can combine with geology to create a coal burst hazard. Nearly every longwall mine operating within the Utah’s Book Cliffs coalfield has been affected by coal bursts.

Jan 7, 2020

To gather additional field data from the western United States, researchers from the National Institute for Occupational Safety and Health (NIOSH) installed an array of field instrumentation at a longwall coal mine in Central Utah. The purpose of this field site was to monitor ground movement and changes in pressure during mining where conditions include massive, stiff overburden and relatively deep cover. To accomplish this, field instrumentation was installed in the two-entry gate road between the fifth and sixth longwall panel in the current mining district.

Jan 7, 2020

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By R. Jacobs, R. E. L. Pobe

The Moab Khotsong Metallurgical Complex comprises a gold recovery circuit (Noligwa Gold Plant) and a uranium recovery circuit (South Uranium Plant). The metallurgical complex employs the reverse leach technology for the recovery of uranium; specifically, uranium extraction prior to gold using acid leaching processing. The inherent uranium species in the ore are uraninite, coffinite and brannerite. The slurry that has been subjected to the uranium leach is further subjected to solid-liquid separation to separate the uranium in a solution through counter-current decantation and the solids (solids carrying all the gold), which are repulped and returned to the gold plant for gold processing. The uranium leaching process is critical to the uranium playing a pivotal role as a value adding by-product to the gold operation. The benefit of adopting this reverse leach process, for improved gold recovery, is that it exposes gold particles occluded within the uranium matrices and avails them for cyanidation. However, the drive for operational efficiency in uranium extraction must be weighed against the incremental operating cost against the backdrop of depressed spot uranium market prices. Over the years, efforts were directed at maintaining the benefit of extracting uranium to enhance gold recovery and simultaneously, optimising the operating cost model for the uranium operation to remain relevant to the gold operation. The aim of this paper and the corresponding presentation is to give an account of the uranium processing optimisation journey embarked on over the years; namely, the operational tradeoffs made in the process of ensuring that uranium continues to add value to the gold operation. These challenges were faced while striking a fine balance between processing cost and operational efficiencies against the prevailing depressed uranium spot market prices. Mineralogical- and laboratory tests conducted form the support basis for the results and observations articulated in the paper. Keywords: By-products, gold extraction, reverse leach benefit, uranium extraction

Jan 1, 2020

By L Dyer, G. J. Wilkie, P. Walters, B Tadesse, L. Keeney

Grade Engineering® is a term trademarked by the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and includes five key levers for upgrading ores and rejecting waste prior to expensive downstream comminution and mineral processing. These five levers include natural deportment, induced deportment, bulk sorting, particle sorting and gravity separation. Over the past ten years, CRC ORE has progressed a range of technologies that exploit these levers from laboratory proof of concept through to large scale demonstration and validation. This paper details the work carried out by CRC ORE and Curtin University for assessing the amenability of an ore for its natural deportment and particle sorting attributes in an Integrated Screening and Particle Sorting (ISPS) Grade Engineering® process. ISPS is seen as a preferred method for Grade Engineering® as compared to individually operated unit operations as the benefits of each can be complementary. Furthermore, it is suggested that integrating the two levers has two important impacts: 1. Firstly, there is a risk that isolated particle sorting test results will be misinterpreted as being representative of the full sample without considering the mass balance impact of high-grade material that might have been lost in the fines fraction. This fine fraction will not be detected through the particle sorter. 2. Secondly, and potentially of more valuable impact, is that the opportunity may exist to upgrade the feed first through determining if there is a concentration of high grade to the fine (or coarse) fraction which can be separated through screening. Undertaking screening in the preparation stage of the particle sorting process will enable analysis and separation of the fine or coarse fractions of a rock mass. The result of this study provides the mining industry with an independent framework for undertaking an Order of Magnitude (ISPS) Grade Engineering® assessment on a range of constituent ore types. Keywords: Grade engineering, particle sorting, grade by size fractionation

Jan 1, 2020

By E. Tabosa, S. Vianna, K. Duffy, W. Valery, B. Andrade, L. Pyle, P. Holtham

Pneumatic flotation cells are high-intensity flotation machines with rapid kinetics, resulting in short residence times. Examples include the Jameson, PneuFlot and ImhoFlot cells. These cells do not use impeller-like mechanical cells. Rather, the air and pulp are mixed in a continuous stream of high fluid velocity through a downcomer or venturi to disperse the air into fine (approximately 0.5 mm) bubbles and maintain particle suspension. Froth wash water is often used to enhance concentrate grade, minimising recovery by entrainment. With the growing application of these types of cells, not only in cleaner stages (their traditional use) but also in pre-flotation and scalping duties, there is a need to predict their performance more accurately for circuit design and optimisation. No widely accepted model for pneumatic flotation cells is available and their metallurgical performance is often scaled up from laboratory and/or pilot plant testing by assuming fixed values for metal recovery, concentrate grade and concentrate percent solids. This paper describes a new approach to simulate pneumatic flotation cell performance and presents case studies demonstrating its applicability. Keywords: Pneumatic flotation, flotation modelling, flotation circuit design, flotation circuit optimisation, Jameson cell

Jan 1, 2020

By J. A. Sweet, T. BACHMANN, G. E. Sandoval, T. M. Hauyon, F. A. Contreras

In many respects a porphyry copper ore concentrator plant can be considered as a simple system. Chalcopyrite typically liberates well at relatively coarse sizes, and even low grade ores are amenable to upgrading 20 to 30 times to produce concentrate grades in excess of 25 % in very simple Rougher- Regrind-Cleaner+Scavenger flotation circuits. The flotation response of chalcopyrite has been well characterised in many fundamental and applied research studies and the conditions necessary to depress pyrite and other floating gangue species are well understood. But what happens to the particle surfaces when you have a 50 km pipeline between the grinding circuit and the flotation plant? How does the seasonal variation in water quality affect your ability to control pulp chemistry? What impact does the relative concentration of the different sulphide species have on their separability? Why do two plants that receive nominally the same ore produce consistently different results? And most importantly, what do you need to do to improve the performance of both plants? To answer these and other questions, a focussed sampling and analysis programme was carried out at the Las Tórtolas flotation plants in 2018 and 2019. The work included full down-the-bank sampling, hot floats, the use of radioactive tracers for determining residence time distribution profiles, gas dispersion measurements, detailed mineralogy by size across the circuits and multiple regrind surveys. This comprehensive study was augmented by analysis of historical mineralogy, geometallurgy and operating data using modern data science techniques, and has provided the foundation for current and future optimisation initiatives. Some of the findings and their implementation will be presented in this paper. Keywords: Circuit optimization, Residence time, Gas dispersion, Pulp chemistry

Jan 1, 2020

By F. S. Hoseinian, B. Rezai, E. Kowsari, M. Safari

In order to remove heavy metal ions from a large volume of wastewater with a low ion concentration, ion flotation appears to be promisingly effective. In the ion flotation process, because of the high ion removal percentage, the amount of water recovery percentage is a very important factor which determines the process efficiency. However, ion flotation suffers from relatively high collector concentration to achieve the high removal percentage to the desired limit, which subsequently increases the water recovery. In this study, functionalised graphene oxide (FGO) was synthesised, using a chemical method in the ion flotation process, applied as a collector for increasing process efficiency by reducing the collector consumption and water recovery. The high ion removal was achieved with both collectors of sodium dodecyl sulfate (SDS) and FGO, while the water recovery with a collector of SDS was 3.4% higher than that with a collector of FGO. The results indicated that the FGO could be effectively used for high ion removal and low water recovery in the ion flotation process. Keywords: Ion flotation, synthesised collector, ion removal, wastewater, water recovery

Jan 1, 2020

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By F. Nakhaei, A. Noury, S. Ghodrati

To achieve maximum efficiency in any purification stage, the flotation should be continued until the concentrate grade reaches the feed grade. During sampling from rougher cells of the Iranian Sarcheshmeh copper concentrator plant 1, it was revealed that the concentrate grade of the last five cells of rougher circuit was close to feed grade. Therefore, it was suggested that the concentrate of the aforementioned cells be mixed with rougher feed. In this study, one of eight rougher circuit rows was selected and evaluated. The floatability tests were performed to compare the flotation behaviour of rougher feed and mixture of concentrate of the last five cells with rougher feed in the laboratory scale by a tree analysis process. The results showed that mixing of rougher last five cell concentrate with feed has a detrimental effect on flotation efficiency that leads to a 3% decrease in recovery. It was also observed that with grinding of this concentrate, recovery can be improved. Keywords: Efficiency, flotation, rougher, tree analysis, floatability, concentrate, mixing

Jan 1, 2020

By Y. Yang, M. Zhang, X. Xia, S Shi, Z. Shen

A stepwise arrangement of flotation cells is the most common layout of a flotation circuit in the mineral processing industry. In such a design, slurry flows from upstream to downstream by means of gravity, and the middling products are returned to previous stages by pumps. This paper will introduce an alternative solution in which the forced-air and slurry-induced flotation cells are adopted so that all the flotation cells can be placed on the same horizontal platform and no pumps will be needed for middling product transferring. The technology of the forced-air and slurry-induced flotation cell will be described in detail, including unique features, the working principle and the related fundamental problems. The comparison of capital investment, operating cost and metallurgical performance will be made between the conventional stepwise arrangement and the samelevel arrangement technology based on industrial practice. Keywords: Forced-air and slurry-induced flotation cell, same-level arrangement, stepwise

Jan 1, 2020

By K. Duffy, W. Valery, L. Pyle, P. Holtham

A conceptual scoping study was conducted to investigate pre-concentration options for upgrading ore from an Ag-Pb-Zn deposit. The low grade of the ore would result in only modest economic returns, given current market conditions. Several pre-concentration options were considered. These included: selective mining, crushing and pre-screening (following either standard or high intensity selective blasting), bulk ore sorting, particle sorting, jigging, dense medium separation, or combinations of these approaches. Flowsheets were developed for each option, and the upgrade performance was modelled using Limn to determine mass balances and stream tables. Due to the limited availability of test work data, the models were based not only on what test data was available but also on case study data found in the literature. The Bazin technique was used to derive assay by size data for different streams following crushing. Equipment lists and preliminary layouts were established based on the stream tables, and capital and operating costs were estimated for each flowsheet. This information was used to carry out a preliminary economic evaluation using net present value and sensitivity analysis. In this case, the most economically attractive process was found to be particle sorting; although further benefits may be realised by combining with bulk sorting. This paper describes the methodology used and the key findings of the study. Keywords: Pre-concentration, pre-screening, ore sorting, jigging, Ag-Pb-Zn, particle sorting, bulk ore sorting

Jan 1, 2020

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020