Search Documents

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By L. Betteridge, A. Marks

"An OK 300 cu. ft. Skim - Air cell was installed at the HBM&S concentrator in Flin Flon in 1987. Since that time, 3 additional OK Skim - Air cells have been installed in HBM&S concentrators. The cell treats a coarse 70% solids slurry with a residence time of 2.5 minutes. The product from the cell (a unit cell type application) is a final grade copper concentrate with high precious metal values. Since its installation, the cell has improved gold recovery by 10 - 15%. Process variables such as circulating load, pH, froth depth, feed size, and reagent additions all have an effect on the operation of the cell. Maintenance on the cell has been minimal. Initial operating problems involving level control have been significantly reduced and operations are now relatively trouble free. Although very successful at Flin Flon, site specific operating circumstances will determine the suitability of this cell. INTRODUCTIONHudson Bay Mining and Smelting operates four concentrators in Northern Manitoba. Three treat copper-zinc ores, the fourth mills a copper-nickel ore. The Flin Flan concentrator operates two circuits in parallel which treat copper and zinc ores from the Trout Lake and Callinan mines. Both circuits in the Flin Flan mill have Skim-Air cells integrated into the grinding circuits.The Trout Lake cell was installed first and had a payback period of a few months. Required modifications to the cell were made to enhance its performance. These included changing the discharge valve size, tuning the level controller, and installing an insert into the rubber valve sleeve to increase its wear life. The payback period on the Callinan cell was significantly reduced because these modifications were completed prior to its installation.The cells produce a final grade copper concentrate and since their installation gold and silver recoveries to the final copper concentrate have increased significantly. Operating parameters such as coarseness of cell feed dictate the metal recoveries and froth depth determines the selectivity of the cell and therefore the grade of the concentrate.The Skim-Air cell can be suitable in applications where a final product is generated. However, when a bulk concentrate, which requires further separation, is produced, the coarseness of the product may not make it amenable to conventional flotation.The Flin Flan mills Skim-Air cells have worked exceptionally well with little maintenance required."

Jan 1, 1991

"The first SkimAir flash flotation cell was installed in Outokumpu’s Hammaslahti Copper Concentrator in 1982 to prevent overgrinding of soft sulphides in the milling circuit. Since this first installation the popularity of the flash flotation has fluctuated depending on metal market conditions and regional preferences. Units have been installed in many commodities including copper, lead, gold, PGMs, silver and nickel. Though it has been successfully employed in many operations around the world, flash flotation technology is still not well understood by many in the mining industry. This paper will discuss aspects of flash flotation flowsheet development along with some of the metallurgical and engineering considerations required to successfully incorporate flash flotation into new or existing milling circuits. This paper will also try and debunk some of the myths that exist around flash flotation cells and their operation. Case studies of flash flotation implementation will be discussed.IntroductionModern flash flotation technology was developed several decades ago by Outokumpu, with the first commercial installation of this technology being at the Hammaslahti concentrator in Finland in 1982 (Kallioinen & Niitti, 1985). This was a relatively modestly sized SK80 cell producing final grade copper concentrate directly from the flash flotation cell operating in the grinding circuit. Since that time the size and number of flash flotation cells installed globally has grown considerably to the point where today, it is a widely known application of flotation technology for amenable ores. Owing to their long history in developing the technology, Outotec are the market leader with their SkimAir range of flash flotation cells. Though there is a general awareness of flash flotation process in the mineral processing industry, there is a lack of detailed understanding of the process and the benefits it can provide to new and existing operations."

Jan 1, 2017

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By W. G. Davenport

A flash furnace can be run many different ways. It can, for example, be operated with: (a) highly 02"enriched, ambient temperature blast and no fossil fuel (b) considerable fossil fuel and hot, slightly Or enriched blast. It can also produce different grades of matte. With all these possibilities, the flash furnace operator can benefit from any technique that will indicate the 'best' way to operate his furnace. One such technique is Excel's 'Solver'optimizationroutine#. This chapter shows how our matrices and Excers optimization.abllity can be used to optimize a flash furnace operation. The chapter sets three optimization goals: (a) minimum industrial oxygen + oil cost, $ per tonne of concentrate (b) maximum smelting rate, tonnes of concentrate per hour (c) maximum profit, $ per hour.

Jan 1, 2001

By Elliot B. J

Flash smelting is a complex and capital intensive technology. Although in use for 50 years the technology is still not well understood from a fundamental point of view and thus uncertainty is evident when significant change to the practice is necessitated. The application of effective design and process simulation tools has significant advantages when process change and improvement is required. Mathematical models have been used to simulate the processes occurring in the shafts of copper flash smelters. The present approach to flash furnace modelling differs from earlier work in that the burners were modelled in detail, the output from the burner model becoming the input to the shaft model. This paper serves as an introduction to the modelling process used to analyse the performance and provide a better understanding of the parameters applicable to the flash furnace at the Kalgoorlie Nickel Smelter.

Jan 1, 1992

By Nickolas J. Themelis

The flash oxidation and smelting of mineral sulfides is a very prominent metallurgical achievement of the second part of this century. Its initial industrial implementation owes much to the work of Petri Bryk, in Finland, and Paul Queneau, in Canada. However, attempts to develop flash reduction pro- cesses, such as the reduction of iron oxide concentrates with hydrogen, have not yet been successful. The author, on the basis of experimental studies on both kinds of flash reaction systems, examines the respective rate controlling phenomena and the relative rates of flash oxidation and flash reduction.

Jan 1, 1993

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Tom Gonzales

At San Manuel, AZ, Magma Metals Co. operates an Outokumpu flash furnace, four Peirce-Smith converters and two anode casting wheels that are supported by six anode vessels. Process gasses from the flash furnace and converters are treated in a two-train/ double-contact sulfuric acid plant. The plant captures 98% of the sulfur. A new flash furnace was commissioned in July 1988. It has since processed more than 2.7 Mt (3 million st) of sulfide concentrate without a major rebuild. The company has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. Process flow description At Magma's San Manuel plant, concentrates and other copper-bearing material are blended and conveyed from two separate areas of the plant to three 420 t (465 st) capacity wet charge bins located above the rotary dryer. Flash furnace silica flux is conveyed to a 227-t (250-st) capacity fine flux bin located adjacent to the wet charge bins. The concentrate and flux are blended in controlled amounts and fed into a 168-t/ h (185-stph) gas-fired rotary dryer. The wet charge enters the dryer at 8% moisture and is dried to 0.2% moisture. The dried charge is pneumatically conveyed to a 580-t/h (640-stph) dry charge bin located above the flash furnace. Flash furnace charge is drawn from the bin by two drag conveyors at a concentrate feed rate of 145 t/h (160 stph). The charge is mixed with enriched combustion air and injected into the furnace reaction shaft. In the reaction shaft, the charge is oxidized to form matte, slag and a rich SO, off-gas.

Jan 1, 1992

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By Tom W. Gonzales

Magma Metals Company commissioned a 3000 tpd Outokumpu flash smelting furnace in July 1988. Through September 1992 the PSP has smelted a first campaign record 4.1 million tons of concentrate. This paper discusses modifications made to the original process equipment to overcome design flaws as well as future design changes currently under consideration.

Jan 1, 1993

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Petri Bryk, John Ryselin, Rolf Malmstrom, Jorma Honkasalo

THE theoretical possibilities for the realization of flash smelting have been known for a long time. Calculations concerning the same can be found in previously published literature,1 and suggestions for its accomplishment in practice are described in patents on the subject. Likewise a smaller number of practical test results are known. Autogenous smelting is closely connected with flash smelting, since in flash smelting techniques it is possible to use the heat evolved by oxidation of the sulfides for the smelting process to such an extent that under certain conditions smelting can proceed without additional fuel. However, in the event that insufficient heat is available from the oxidation of the sulfide concentrates, then additional heat may be supplied by preheating the air, using oxygen enriched air, on burning additional fuel with the concentrate.

Jan 6, 1958

By N. S. Dalal, Xianglin Shi

"The mechanism of vanadium(V) V ) toxicity is still not fully understood in spite of extensive current effort (1-3). The presence of a vanadium(V) V ) -dependent NAD ( P )H oxidase in cell membranes suggests that at least one of the pathways involves oxidation of NAD(P)H (1-3). Considerable effort has therefore been devoted to finding the mechanism of NAD ( P ) H-oxidation by va¬nadium( V ) (1-19). Recently Liochev and Fridovich (4, 16) provided a critical review of vanadium( V) -stimulated NAD (P )H oxidation by plasma membranes. They out¬lined a mechanism in which vanadium(V) V )-stimulated oxidation of NAD ( P )H by biomembranes involves an O2 - initiated free radical chain reaction (4 ). While the above may be the major pathway for the vanadium-me¬diated NAD (P )H oxidation in membrane-related sys¬tems, some recent results suggest that in the presence of NADPH the flavoenzyme glutathione reductase can function as a vanadium(V) V ) reductase (18). Because of the significance of this result in relationship to the mech¬anism of vanadium( V) metabolism and the novelty of the metal-reductase behavior of a flavoenzyme, we have car¬ried out additional studies on one-electron reduction of vanadium( V) by two other, related flavoenzymes: lipoyl dehydrogenase and ferredoxin-NADPH oxidoreductase. These two enzymes were selected because they are known to catalyze a one-electron reduction of Cr ( VI ) (19-21 ), which is isoelectronic with vanadium( V ).The present study also reports on the generation of hydroxyl ( • OH) radicals in the vanadium( V) -flavoen-zyme redox system without exogenous H2O2. The • OH study was undertaken because • OH radicals are known to be generated in reactions of vanadium( IV) with H2O2 (17,18,22-27). For example, Piette and co-workers (17, 22) have studied effects of vanadium(IV) IV ) on lipid per-oxidation and NADPH oxidation and suggested that va-nadium( IV) -induced • OH radical formation may play an important role in vanadium( V) toxicity. Carmichael (25, 26) investigated the reaction between a RNA /VO 2' complex and H2O2 with a view to probe the possible re-lationship between vanadium( IV) -mediated • OH radical generation and DNA damage. He has suggested that in this reaction the • OH radical adds to the C (5) carbon of uracil, causing nucleotide damage, similar to what occurs in the nucleotide /Fe2+ / H2O2 reaction (28) and in y-irradiated aqueous solutions of nucleic acids (29 ). To our knowledge, however, there is as yet no report on ·OH radical generation in any reaction involving the reduction of vanadium ( V) by a well-characterized enzyme, without exogenous H20 2 • The present study provides evidence that ·OH radicals can form in a flavoenzyme-mediated reduction of vanadium( V) to vanadium( IV) and that this process involves also the reduction of molecular oxygen ( 0 2 ) to H20 2 • The H20 2 thus generated reacts with vanadium( IV) to produce ·OH radical, in analogy with the Fenton reaction ( Fe2 + + H20 2 - Fe3 + + OH- + ·OH)."

Mar 1, 1992

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By R. Grimard, M. Gamache, L. -P. Bigras, P. Cohen

This paper describes a real-time fleet management system for an undergroun mine. Dispatching, routing and scheduling are handled simultaneously, taking into account the mine status, operational constraints and vehicle location information. Each assignment decision takes into account the traffic on the road segments of the mine network, whether road segments are bi-directional or uni-directional, and ensures that each LHD (load-haul-dump) vehicle arrives at loading and dumping points with the correct orientation. Such a system can be used either as a simulation tool for strategic planning or as a real-time managing and optimizing system for operations. In the simulation mode, the system can accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. When used for real-time dispatching, routing and scheduling of vehicles, the system can optimize production with respect to various assignment criteria such as cycle-time minimization or deviation from a target production plan.

Jan 1, 2004

By Josef Arnold, Norbert Fuegenschuh

The “Eggequerung” is an important part of the German Railway’s (Deutsche BahnAG) modernized Dortmund—Kassel line. The heart of this 13-km-long (8 miles)construction lot is the double-track Egge Tunnel with a total length of 2,880 m(9,450 ft.). The tunnel was driven using the New Austrian Tunnelling Method (NATM).The construction contract also called for a reinforced concrete secondary lining, guaranteed for a full water pressure of 30 m (100 ft.) water column. Preliminary geological study already showed that very problematic geological-hydrological conditions would have to be expected. This talk describes the chosen NATM driving concept that was adapted to the prevailing geological and hydrological conditions, the special driving method applied in geologically difficult zones as well as the water control concept used during driving. The flexibility and the limits of the NATM under exceptional hydrological conditions are illustrated. Also described are reinforced concrete lining works for the watertight secondary vault (reinforced concrete secondary lining without water-proofing membrane).

Jan 1, 2003

By K. Eklund, T. Ahokainen

The Flash Smelting process is the most used production method for primary copper in the world. The basic idea of the Flash Smelting is to utilize the thermal value of sulfidic concentrates and melt the reaction product, in controlled conditions, without a need for external energy. This basic principle is utilized both in matte smelting and in Direct-to-Blister Flash Smelting Processes. In this paper, the behavior of normal (CuFeS2) concentrate of FSF-process is compared to the behavior of high grade feed material produced by Outokumpu Concentrate Upgrade Process with the aid of computational fluid dynamics (CPD) simulation using add-in subroutines developed by Outokumpu Technology. Results consist of the information concerning the behavior of the suspension, reaction efficiency and other parameters concerning the reactions of the feed material. It will be shown that, using the Upgrade Process, the throughput of copper from the Flash Furnace can be almost tripled.

Jan 1, 2007

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995